ADSL2-LINE-TC-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, transmission FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC; adsl2TCMIB MODULE-IDENTITY LAST-UPDATED "200610040000Z" -- October 4th, 2006 ORGANIZATION "ADSLMIB Working Group" CONTACT-INFO "WG-email: [email protected] Info: https://www1.ietf.org/mailman/listinfo/adslmib Chair: Mike Sneed Sand Channel Systems Postal: P.O. Box 37324 Raleigh NC 27627-732 Email: [email protected] Phone: +1 206 600 7022 Co-Chair & Co-editor: Menachem Dodge ECI Telecom Ltd. Postal: 30 Hasivim St. Petach Tikva 49517, Israel. Email: [email protected] Phone: +972 3 926 8421 Co-editor: Moti Morgenstern ECI Telecom Ltd. Postal: 30 Hasivim St. Petach Tikva 49517, Israel. Email: [email protected] Phone: +972 3 926 6258 Co-editor: Scott Baillie NEC Australia Postal: 649-655 Springvale Road, Mulgrave, Victoria 3170, Australia. Email: [email protected] Phone: +61 3 9264 3986 Co-editor: Umberto Bonollo NEC Australia Postal: 649-655 Springvale Road, Mulgrave, Victoria 3170, Australia. Email: [email protected] Phone: +61 3 9264 3385 " DESCRIPTION "This MIB Module provides Textual Conventions to be used by the ADSL2-LINE-MIB module for the purpose of managing ADSL, ADSL2, and ADSL2+ lines. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4706: see the RFC itself for full legal notices." REVISION "200610040000Z" -- October 4th, 2006 DESCRIPTION "Initial version, published as RFC 4706." ::= { transmission 238 2 } -- adsl2MIB 2 ------------------------------------------------ -- Textual Conventions -- ------------------------------------------------ Adsl2Unit ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Identifies a transceiver as being either an ATU-C or an ATU-R. An ADSL line consists of two transceivers, an ATU-C and an ATU-R. Attributes with this syntax reference the two sides of a line. Specified as an INTEGER, the two values are: atuc(1) -- Central office ADSL terminal unit (ATU-C). atur(2) -- Remote ADSL terminal unit (ATU-R)." SYNTAX INTEGER { atuc(1), atur(2) } Adsl2Direction ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Identifies the direction of a band as being either upstream or downstream. Specified as an INTEGER, the two values are: upstream(1), and downstream(2)." SYNTAX INTEGER { upstream(1), downstream(2) } Adsl2TransmissionModeType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A set of ADSL2 line transmission modes, with one bit per mode. The notes (F) and (L) denote Full-Rate and Lite/splitterless, respectively: Bit 00 : Regional Std. (ANSI T1.413) (F) Bit 01 : Regional Std. (ETSI DTS/TM06006) (F) Bit 02 : G.992.1 POTS non-overlapped (F) Bit 03 : G.992.1 POTS overlapped (F) Bit 04 : G.992.1 ISDN non-overlapped (F) Bit 05 : G.992.1 ISDN overlapped (F) Bit 06 : G.992.1 TCM-ISDN non-overlapped (F) Bit 07 : G.992.1 TCM-ISDN overlapped (F) Bit 08 : G.992.2 POTS non-overlapped (L) Bit 09 : G.992.2 POTS overlapped (L) Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L) Bit 11 : G.992.2 with TCM-ISDN overlapped (L) Bit 12 : G.992.1 TCM-ISDN symmetric (F) -- not in G.997.1 Bit 13-17: Reserved Bit 18 : G.992.3 POTS non-overlapped (F) Bit 19 : G.992.3 POTS overlapped (F) Bit 20 : G.992.3 ISDN non-overlapped (F) Bit 21 : G.992.3 ISDN overlapped (F) Bit 22-23: Reserved Bit 24 : G.992.4 POTS non-overlapped (L) Bit 25 : G.992.4 POTS overlapped (L) Bit 26-27: Reserved Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F) Bit 29 : G.992.3 Annex I All-Digital overlapped (F) Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F) Bit 31 : G.992.3 Annex J All-Digital overlapped (F) Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L) Bit 33 : G.992.4 Annex I All-Digital overlapped (L) Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1, wide U/S (F) Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2, narrow U/S(F) Bit 36 : G.992.3 Annex L POTS overlapped, mode 3, wide U/S (F) Bit 37 : G.992.3 Annex L POTS overlapped, mode 4, narrow U/S (F) Bit 38 : G.992.3 Annex M POTS non-overlapped (F) Bit 39 : G.992.3 Annex M POTS overlapped (F) Bit 40 : G.992.5 POTS non-overlapped (F) Bit 41 : G.992.5 POTS overlapped (F) Bit 42 : G.992.5 ISDN non-overlapped (F) Bit 43 : G.992.5 ISDN overlapped (F) Bit 44-45: Reserved Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F) Bit 47 : G.992.5 Annex I All-Digital overlapped (F) Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F) Bit 49 : G.992.5 Annex J All-Digital overlapped (F) Bit 50 : G.992.5 Annex M POTS non-overlapped (F) Bit 51 : G.992.5 Annex M POTS overlapped (F) Bit 52-55: Reserved" SYNTAX BITS { ansit1413(0), etsi(1), g9921PotsNonOverlapped(2), g9921PotsOverlapped(3), g9921IsdnNonOverlapped(4), g9921isdnOverlapped(5), g9921tcmIsdnNonOverlapped(6), g9921tcmIsdnOverlapped(7), g9922potsNonOverlapped(8), g9922potsOverlapped(9), g9922tcmIsdnNonOverlapped(10), g9922tcmIsdnOverlapped(11), g9921tcmIsdnSymmetric(12), reserved1(13), reserved2(14), reserved3(15), reserved4(16), reserved5(17), g9923PotsNonOverlapped(18), g9923PotsOverlapped(19), g9923IsdnNonOverlapped(20), g9923isdnOverlapped(21), reserved6(22), reserved7(23), g9924potsNonOverlapped(24), g9924potsOverlapped(25), reserved8(26), reserved9(27), g9923AnnexIAllDigNonOverlapped(28), g9923AnnexIAllDigOverlapped(29), g9923AnnexJAllDigNonOverlapped(30), g9923AnnexJAllDigOverlapped(31), g9924AnnexIAllDigNonOverlapped(32), g9924AnnexIAllDigOverlapped(33), g9923AnnexLMode1NonOverlapped(34), g9923AnnexLMode2NonOverlapped(35), g9923AnnexLMode3Overlapped(36), g9923AnnexLMode4Overlapped(37), g9923AnnexMPotsNonOverlapped(38), g9923AnnexMPotsOverlapped(39), g9925PotsNonOverlapped(40), g9925PotsOverlapped(41), g9925IsdnNonOverlapped(42), g9925isdnOverlapped(43), reserved10(44), reserved11(45), g9925AnnexIAllDigNonOverlapped(46), g9925AnnexIAllDigOverlapped(47), g9925AnnexJAllDigNonOverlapped(48), g9925AnnexJAllDigOverlapped(49), g9925AnnexMPotsNonOverlapped(50), g9925AnnexMPotsOverlapped(51), reserved12(52), reserved13(53), reserved14(54), reserved15(55) } Adsl2RaMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the rate adaptation behavior for the line. The three possible behaviors are: manual(1) - No Rate-Adaptation. The initialization process attempts to synchronize to a specified rate. raInit(2) - Rate-Adaptation during initialization process only, which attempts to synchronize to a rate between minimum and maximum specified values. dynamicRa(3) - Dynamic Rate-Adaptation during initialization process as well as during SHOWTIME." SYNTAX INTEGER { manual(1), raInit(2), dynamicRa(3) } Adsl2InitResult ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the result of a full initialization attempt; the six possible result values are: noFail(0) - Successful initialization. configError(1) - Configuration failure. configNotFeasible(2) - Configuration details not supported. commFail(3) - Communication failure. noPeerAtu(4) - Peer ATU not detected. otherCause(5) - Other initialization failure reason. The values used are as defined in ITU-T G.997.1, paragraph 7.5.1.3" SYNTAX INTEGER { noFail(0), configError(1), configNotFeasible(2), commFail(3), noPeerAtu(4), otherCause(5) } Adsl2OperationModes ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The ADSL2 management model specified includes an ADSL Mode attribute that identifies an instance of ADSL Mode-Specific PSD Configuration object in the ADSL Line Profile. The following classes of ADSL operating mode are defined. The notes (F) and (L) denote Full-Rate and Lite/splitterless respectively: +-------+--------------------------------------------------+ | Value | ADSL operation mode description | +-------+--------------------------------------------------+ 1 - The default/generic PSD configuration. Default configuration will be used when no other matching mode-specific configuration can be found. 2 - ADSL family. The attributes included in the Mode- Specific PSD Configuration are irrelevant for ITU-T G.992.1 and G.992.2 ADSL modes. Hence, it is possible to map those modes to this generic class. 3-7 - Unused. Reserved for future ITU-T specification. 8 - G.992.3 POTS non-overlapped (F) 9 - G.992.3 POTS overlapped (F) 10 - G.992.3 ISDN non-overlapped (F) 11 - G.992.3 ISDN overlapped (F) 12-13 - Unused. Reserved for future ITU-T specification. 14 - G.992.4 POTS non-overlapped (L) 15 - G.992.4 POTS overlapped (L) 16-17 - Unused. Reserved for future ITU-T specification. 18 - G.992.3 Annex I All-Digital non-overlapped (F) 19 - G.992.3 Annex I All-Digital overlapped (F) 20 - G.992.3 Annex J All-Digital non-overlapped (F) 21 - G.992.3 Annex J All-Digital overlapped (F) 22 - G.992.4 Annex I All-Digital non-overlapped (L) 23 - G.992.4 Annex I All-Digital overlapped (L) 24 - G.992.3 Annex L POTS non-overlapped, mode 1, wide U/S (F) 25 - G.992.3 Annex L POTS non-overlapped, mode 2, narrow U/S(F) 26 - G.992.3 Annex L POTS overlapped, mode 3, wide U/S (F) 27 - G.992.3 Annex L POTS overlapped, mode 4, narrow U/S (F) 28 - G.992.3 Annex M POTS non-overlapped (F) 29 - G.992.3 Annex M POTS overlapped (F) 30 - G.992.5 POTS non-overlapped (F) 31 - G.992.5 POTS overlapped (F) 32 - G.992.5 ISDN non-overlapped (F) 33 - G.992.5 ISDN overlapped (F) 34-35 - Unused. Reserved for future ITU-T specification. 36 - G.992.5 Annex I All-Digital non-overlapped (F) 37 - G.992.5 Annex I All-Digital overlapped (F) 38 - G.992.5 Annex J All-Digital non-overlapped (F) 39 - G.992.5 Annex J All-Digital overlapped (F) 40 - G.992.5 Annex M POTS non-overlapped (F) 41 - G.992.5 Annex M POTS overlapped (F) " SYNTAX INTEGER { defMode (1), adsl(2), g9923PotsNonOverlapped(8), g9923PotsOverlapped(9), g9923IsdnNonOverlapped(10), g9923isdnOverlapped(11), g9924potsNonOverlapped(14), g9924potsOverlapped(15), g9923AnnexIAllDigNonOverlapped(18), g9923AnnexIAllDigOverlapped(19), g9923AnnexJAllDigNonOverlapped(20), g9923AnnexJAllDigOverlapped(21), g9924AnnexIAllDigNonOverlapped(22), g9924AnnexIAllDigOverlapped(23), g9923AnnexLMode1NonOverlapped(24), g9923AnnexLMode2NonOverlapped(25), g9923AnnexLMode3Overlapped(26), g9923AnnexLMode4Overlapped(27), g9923AnnexMPotsNonOverlapped(28), g9923AnnexMPotsOverlapped(29), g9925PotsNonOverlapped(30), g9925PotsOverlapped(31), g9925IsdnNonOverlapped(32), g9925isdnOverlapped(33), g9925AnnexIAllDigNonOverlapped(36), g9925AnnexIAllDigOverlapped(37), g9925AnnexJAllDigNonOverlapped(38), g9925AnnexJAllDigOverlapped(39), g9925AnnexMPotsNonOverlapped(40), g9925AnnexMPotsOverlapped(41) } Adsl2PowerMngState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax uniquely identify each power management state defined for the ADSL/ADSL2 or ADSL2+ link. The possible values are: l0(1) - L0 - Full power management state. l1(2) - L1 - Low power management state (for G.992.2). l2(3) - L2 - Low power management state (for G.992.3, G.992.4, and G.992.5). l3(4) - L3 - Idle power management state." SYNTAX INTEGER { l0(1), l1(2), l2(3), l3(4) } Adsl2ConfPmsForce ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that reference the desired power management state for the ADSL/ADSL2 or ADSL2+ link: l3toL0(0) - Perform a transition from L3 to L0 (Full power management state). l0toL2(2) - Perform a transition from L0 to L2 (Low power management state). l0orL2toL3(3) - Perform a transition into L3 (Idle power management state). The values used are as defined in ITU-T G.997.1, paragraph 7.3.1.1.3" SYNTAX INTEGER { l3toL0(0), l0toL2(2), l0orL2toL3(3) } Adsl2LConfProfPmMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that reference the power modes/states into which the ATU-C or ATU-R may autonomously transit. It is a BITS structure that allows control of the following transit options: allowTransitionsToIdle(0) - XTU may autonomously transit to idle (L3) state. allowTransitionsToLowPower(1) - XTU may autonomously transit to low-power (L2) state." SYNTAX BITS { allowTransitionsToIdle(0), allowTransitionsToLowPower(1) } Adsl2LineLdsf ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that control the Loop Diagnostic mode for the ADSL/ADSL2 or ADSL2+ link. The possible values are: inhibit(0) - Inhibit Loop Diagnostic mode. force(1) - Force/Initiate Loop Diagnostic mode. The values used are as defined in ITU-T G.997.1, paragraph 7.3.1.1.8" SYNTAX INTEGER { inhibit(0), force(1) } Adsl2LdsfResult ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Possible failure reasons associated with performing a Dual Ended Loop Test (DELT) on a DSL line. Possible values are: none(1) - The default value in case LDSF was never requested for the associated line. success(2) - The recent command completed successfully. inProgress(3) - The Loop Diagnostics process is in progress. unsupported(4) - The NE or the line card doesn't support LDSF. cannotRun(5) - The NE cannot initiate the command, due to a nonspecific reason. aborted(6) - The Loop Diagnostics process aborted. failed(7) - The Loop Diagnostics process failed. illegalMode(8) - The NE cannot initiate the command, due to the specific mode of the relevant line. adminUp(9) - The NE cannot initiate the command, as the relevant line is administratively 'Up'. tableFull(10) - The NE cannot initiate the command, due to reaching the maximum number of rows in the results table. noResources(11) - The NE cannot initiate the command, due to lack of internal memory resources." SYNTAX INTEGER { none(1), success(2), inProgress(3), unsupported(4), cannotRun(5), aborted(6), failed(7), illegalMode(8), adminUp(9), tableFull(10), noResources(11) } Adsl2SymbolProtection ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that reference the minimum-length impulse noise protection (INP) in terms of number of symbols. The possible values are: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol." SYNTAX INTEGER { noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteeSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18) } Adsl2MaxBer ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that reference the maximum Bit Error Rate (BER). The possible values are: eminus3(1) - Maximum BER=E^-3 eminus5(2) - Maximum BER=E^-5 eminus7(3) - Maximum BER=E^-7" SYNTAX INTEGER { eminus3(1), eminus5(2), eminus7(3) } Adsl2ScMaskDs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each one of the 512 bits in this OCTET STRING array represents the corresponding bin in the downstream direction. A value of one indicates that the bin is not in use." SYNTAX OCTET STRING (SIZE(0..64)) Adsl2ScMaskUs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each one of the 64 bits in this OCTET STRING array represents the corresponding bin in the upstream direction. A value of one indicates that the bin is not in use." SYNTAX OCTET STRING (SIZE(0..8)) Adsl2RfiDs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each one of the 512 bits in this OCTET STRING array represents the corresponding bin in the downstream direction. A value of one indicates that the bin is part of a notch filter." SYNTAX OCTET STRING (SIZE(0..64)) Adsl2PsdMaskDs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This is a structure that represents up to 32 PSD Mask breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the sub-carrier associated with the breakpoint. The third octet holds the PSD reduction at the breakpoint from 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of 0.5 dBm/Hz." SYNTAX OCTET STRING (SIZE(0..96)) Adsl2PsdMaskUs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This is a structure that represents up to 4 PSD Mask breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the sub-carrier associated with the breakpoint. The third octet holds the PSD reduction at the breakpoint from 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of 0.5 dBm/Hz." SYNTAX OCTET STRING (SIZE(0..12)) Adsl2Tssi ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This is a structure that represents up to 32 transmit spectrum shaping (TSSi) breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the sub-carrier associated with the breakpoint. The third octet holds the shaping parameter at the breakpoint. It is a value from 0 to 127 (units of -0.5 dB). The special value 127 indicates that the sub-carrier is not transmitted." SYNTAX OCTET STRING (SIZE(0..96)) Adsl2LastTransmittedState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This parameter represents the last successfully transmitted initialization state in the last full initialization performed on the line. States are per the specific xDSL technology and are numbered from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime." SYNTAX INTEGER { atucG9941(0), atucQuiet1(1), atucComb1(2), atucQuiet2(3), atucComb2(4), atucIcomb1(5), atucLineprob(6), atucQuiet3(7), atucComb3(8), atucIComb2(9), atucMsgfmt(10), atucMsgpcb(11), atucQuiet4(12), atucReverb1(13), atucTref1(14), atucReverb2(15), atucEct(16), atucReverb3(17), atucTref2(18), atucReverb4(19), atucSegue1(20), atucMsg1(21), atucReverb5(22), atucSegue2(23), atucMedley(24), atucExchmarker(25), atucMsg2(26), atucReverb6(27), atucSegue3(28), atucParams(29), atucReverb7(30), atucSegue4(31), atucShowtime(32), -- aturG9941(100), aturQuiet1(101), aturComb1(102), aturQuiet2(103), aturComb2(104), aturIcomb1(105), aturLineprob(106), aturQuiet3(107), aturComb3(108), aturIcomb2(109), aturMsgfmt(110), aturMsgpcb(111), aturReverb1(112), aturQuiet4(113), aturReverb2(114), aturQuiet5(115), aturReverb3(116), aturEct(117), aturReverb4(118), aturSegue1(119), aturReverb5(120), aturSegue2(121), aturMsg1(122), aturMedley(123), aturExchmarker(124), aturMsg2(125), aturReverb6(126), aturSegue3(127), aturParams(128), aturReverb7(129), aturSegue4(130), aturShowtime(131) } Adsl2LineStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are status parameters that reflect the failure status for a given endpoint of ADSL/ADSL2 or ADSL2+ link. This BITS structure can report the following failures: noDefect(0) - This bit position positively reports that no defect or failure exists. lossOfFrame(1) - Loss of frame synchronization. lossOfSignal(2) - Loss of signal. lossOfPower(3) - Loss of power. Usually this failure may be reported for ATU-Rs only. initFailure(4) - Recent initialization process failed. Never active on ATU-R." SYNTAX BITS { noDefect(0), lossOfFrame(1), lossOfSignal(2), lossOfPower(3), initFailure(4) } Adsl2ChAtmStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are status parameters that reflect the failure status for Transmission Convergence (TC) layer of a given ATM interface (data path over an ADSL/ADSL2 or ADSL2+ link). This BITS structure can report the following failures: noDefect(0) - This bit position positively reports that no defect or failure exists. noCellDelineation(1) - The link was successfully initialized, but cell delineation was never acquired on the associated ATM data path. lossOfCellDelineation(2) - Loss of cell delineation on the associated ATM data path." SYNTAX BITS { noDefect(0), noCellDelineation(1), lossOfCellDelineation(2) } Adsl2ChPtmStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are status parameters that reflect the failure status for a given PTM interface (packet data path over an ADSL/ADSL2 or ADSL2+ link). This BITS structure can report the following failures: noDefect(0) - This bit position positively reports that no defect or failure exists. outOfSync(1) - Out of synchronization." SYNTAX BITS { noDefect(0), outOfSync(1) } END