DOCS-IETF-BPI2-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, Counter32, mib-2 FROM SNMPv2-SMI -- [RFC2578] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411] TEXTUAL-CONVENTION, MacAddress, RowStatus, TruthValue, DateAndTime, StorageType FROM SNMPv2-TC -- [RFC2579] OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF -- [RFC2580] ifIndex FROM IF-MIB -- [RFC2863] InetAddressType, InetAddress FROM INET-ADDRESS-MIB; -- [RFC4001] docsBpi2MIB MODULE-IDENTITY LAST-UPDATED "200507200000Z" -- July 20, 2005 ORGANIZATION "IETF IP over Cable Data Network (IPCDN) Working Group" CONTACT-INFO "--------------------------------------- Stuart M. Green E-mail: [email protected] --------------------------------------- Kaz Ozawa Automotive Systems Development Center TOSHIBA CORPORATION 1-1, Shibaura 1-Chome Minato-ku, Tokyo 105-8001 Japan Phone: +81-3-3457-8569 Fax: +81-3-5444-9325 E-mail: [email protected] --------------------------------------- Alexander Katsnelson Postal: Tel: +1-303-680-3924 E-mail: [email protected] --------------------------------------- Eduardo Cardona Postal: Cable Television Laboratories, Inc. 858 Coal Creek Circle Louisville, CO 80027- 9750 U.S.A. Tel: +1 303 661 9100 Fax: +1 303 661 9199 E-mail: [email protected] --------------------------------------- IETF IPCDN Working Group General Discussion: [email protected] Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn. Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn. Co-chairs: Richard Woundy, [email protected] Jean-Francois Mule, [email protected]" DESCRIPTION "This is the MIB module for the DOCSIS Baseline Privacy Plus Interface (BPI+) at cable modems (CMs) and cable modem termination systems (CMTSs). Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 4131; see the RFC itself for full legal notices." REVISION "200507200000Z" -- July 20, 2005 DESCRIPTION "Initial version of the IETF BPI+ MIB module. This version published as RFC 4131." ::= { mib-2 126 } -- Textual conventions DocsX509ASN1DEREncodedCertificate ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An X509 digital certificate encoded as an ASN.1 DER object." SYNTAX OCTET STRING (SIZE (0..4096)) DocsSAId ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "Security Association identifier (SAID)." REFERENCE "DOCSIS Baseline Privacy Plus Interface specification, Section 2.1.3, BPI+ Security Associations" SYNTAX Integer32 (1..16383) DocsSAIdOrZero ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "Security Association identifier (SAID). The value zero indicates that the SAID is yet to be determined." REFERENCE "DOCSIS Baseline Privacy Plus Interface specification, Section 2.1.3, BPI+ Security Associations" SYNTAX Unsigned32 (0 | 1..16383) DocsBpkmSAType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of security association (SA). The values of the named-numbers are associated with the BPKM SA-Type attributes: 'primary' corresponds to code '1', 'static' to code '2', and 'dynamic' to code '3'. The 'none' value must only be used if the SA type has yet to be determined." REFERENCE "DOCSIS Baseline Privacy Plus Interface specification, Section 4.2.2.24" SYNTAX INTEGER { none(0), primary(1), static(2), dynamic(3) } DocsBpkmDataEncryptAlg ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The list of data encryption algorithms defined for the DOCSIS interface in the BPKM cryptographic-suite parameter. The value 'none' indicates that the SAID being referenced has no data encryption." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.20." SYNTAX INTEGER { none(0), des56CbcMode(1), des40CbcMode(2), t3Des128CbcMode(3), aes128CbcMode(4), aes256CbcMode(5) } DocsBpkmDataAuthentAlg ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The list of data integrity algorithms defined for the DOCSIS interface in the BPKM cryptographic-suite parameter. The value 'none' indicates that no data integrity is used for the SAID being referenced." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.20." SYNTAX INTEGER { none(0), hmacSha196(1) } docsBpi2MIBObjects OBJECT IDENTIFIER ::= { docsBpi2MIB 1 } -- Cable Modem Group docsBpi2CmObjects OBJECT IDENTIFIER ::= { docsBpi2MIBObjects 1 } -- -- The BPI+ base and authorization table for CMs, -- indexed by ifIndex -- docsBpi2CmBaseTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmBaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the basic and authorization- related Baseline Privacy Plus attributes of each CM MAC interface." ::= { docsBpi2CmObjects 1 } docsBpi2CmBaseEntry OBJECT-TYPE SYNTAX DocsBpi2CmBaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing attributes of one CM MAC interface. An entry in this table exists for each ifEntry with an ifType of docsCableMaclayer(127)." INDEX { ifIndex } ::= { docsBpi2CmBaseTable 1 } DocsBpi2CmBaseEntry ::= SEQUENCE { docsBpi2CmPrivacyEnable TruthValue, docsBpi2CmPublicKey OCTET STRING, docsBpi2CmAuthState INTEGER, docsBpi2CmAuthKeySequenceNumber Integer32, docsBpi2CmAuthExpiresOld DateAndTime, docsBpi2CmAuthExpiresNew DateAndTime, docsBpi2CmAuthReset TruthValue, docsBpi2CmAuthGraceTime Integer32, docsBpi2CmTEKGraceTime Integer32, docsBpi2CmAuthWaitTimeout Integer32, docsBpi2CmReauthWaitTimeout Integer32, docsBpi2CmOpWaitTimeout Integer32, docsBpi2CmRekeyWaitTimeout Integer32, docsBpi2CmAuthRejectWaitTimeout Integer32, docsBpi2CmSAMapWaitTimeout Integer32, docsBpi2CmSAMapMaxRetries Integer32, docsBpi2CmAuthentInfos Counter32, docsBpi2CmAuthRequests Counter32, docsBpi2CmAuthReplies Counter32, docsBpi2CmAuthRejects Counter32, docsBpi2CmAuthInvalids Counter32, docsBpi2CmAuthRejectErrorCode INTEGER, docsBpi2CmAuthRejectErrorString SnmpAdminString, docsBpi2CmAuthInvalidErrorCode INTEGER, docsBpi2CmAuthInvalidErrorString SnmpAdminString } docsBpi2CmPrivacyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies whether this CM is provisioned to run Baseline Privacy Plus." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.1.1." ::= { docsBpi2CmBaseEntry 1 } docsBpi2CmPublicKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..524)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is a DER-encoded RSAPublicKey ASN.1 type string, as defined in the RSA Encryption Standard (PKCS #1), corresponding to the public key of the CM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.4." ::= { docsBpi2CmBaseEntry 2 } docsBpi2CmAuthState OBJECT-TYPE SYNTAX INTEGER { start(1), authWait(2), authorized(3), reauthWait(4), authRejectWait(5), silent(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the state of the CM authorization FSM. The start state indicates that FSM is in its initial state." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.1.2.1." ::= { docsBpi2CmBaseEntry 3 } docsBpi2CmAuthKeySequenceNumber OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the most recent authorization key sequence number for this FSM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.2 and 4.2.2.10." ::= { docsBpi2CmBaseEntry 4 } docsBpi2CmAuthExpiresOld OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the immediate predecessor of the most recent authorization key for this FSM. If this FSM has only one authorization key, then the value is the time of activation of this FSM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.2 and 4.2.2.9." ::= { docsBpi2CmBaseEntry 5 } docsBpi2CmAuthExpiresNew OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the most recent authorization key for this FSM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.2 and 4.2.2.9." ::= { docsBpi2CmBaseEntry 6 } docsBpi2CmAuthReset OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'true' generates a Reauthorize event in the authorization FSM. Reading this object always returns FALSE. This object is for testing purposes only, and therefore it is not required to be associated with a last reset object." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.1.2.3.4." ::= { docsBpi2CmBaseEntry 7 } docsBpi2CmAuthGraceTime OBJECT-TYPE SYNTAX Integer32 (1..6047999) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the grace time for an authorization key in seconds. A CM is expected to start trying to get a new authorization key beginning AuthGraceTime seconds before the most recent authorization key actually expires." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.1.1.1.3." ::= { docsBpi2CmBaseEntry 8 } docsBpi2CmTEKGraceTime OBJECT-TYPE SYNTAX Integer32 (1..302399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the grace time for the TEK in seconds. The CM is expected to start trying to acquire a new TEK beginning TEK GraceTime seconds before the expiration of the most recent TEK." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.1.1.1.6." ::= { docsBpi2CmBaseEntry 9 } docsBpi2CmAuthWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..30) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Authorize Wait Timeout in seconds." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.1.1.1.1." ::= { docsBpi2CmBaseEntry 10 } docsBpi2CmReauthWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..30) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Reauthorize Wait Timeout in seconds." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.1.1.1.2." ::= { docsBpi2CmBaseEntry 11 } docsBpi2CmOpWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..10) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Operational Wait Timeout in seconds." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.1.1.1.4." ::= { docsBpi2CmBaseEntry 12 } docsBpi2CmRekeyWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..10) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Rekey Wait Timeout in seconds." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.1.1.1.5." ::= { docsBpi2CmBaseEntry 13 } docsBpi2CmAuthRejectWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..600) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Authorization Reject Wait Timeout in seconds." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.1.1.1.7." ::= { docsBpi2CmBaseEntry 14 } docsBpi2CmSAMapWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..10) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the retransmission interval, in seconds, of SA Map Requests from the MAP Wait state." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.1.1.1.8." ::= { docsBpi2CmBaseEntry 15 } docsBpi2CmSAMapMaxRetries OBJECT-TYPE SYNTAX Integer32 (0..10) UNITS "count" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the maximum number of Map Request retries allowed." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.1.1.1.9." ::= { docsBpi2CmBaseEntry 16 } docsBpi2CmAuthentInfos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has transmitted an Authentication Information message. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.9." ::= { docsBpi2CmBaseEntry 17 } docsBpi2CmAuthRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has transmitted an Authorization Request message. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.1." ::= { docsBpi2CmBaseEntry 18 } docsBpi2CmAuthReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has received an Authorization Reply message. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.2." ::= { docsBpi2CmBaseEntry 19 } docsBpi2CmAuthRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has received an Authorization Reject message. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.3." ::= { docsBpi2CmBaseEntry 20 } docsBpi2CmAuthInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CM has received an Authorization Invalid message. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.7." ::= { docsBpi2CmBaseEntry 21 } docsBpi2CmAuthRejectErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedCm(3), unauthorizedSaid(4), permanentAuthorizationFailure(8), timeOfDayNotAcquired(11) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent Authorization Reject message received by the CM. This has the value unknown(2) if the last Error-Code value was 0 and none(1) if no Authorization Reject message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.3 and 4.2.2.15." ::= { docsBpi2CmBaseEntry 22 } docsBpi2CmAuthRejectErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the text string in the most recent Authorization Reject message received by the CM. This is a zero length string if no Authorization Reject message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.3 and 4.2.2.6." ::= { docsBpi2CmBaseEntry 23 } docsBpi2CmAuthInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedCm(3), unsolicited(5), invalidKeySequence(6), keyRequestAuthenticationFailure(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent Authorization Invalid message received by the CM. This has the value unknown(2) if the last Error-Code value was 0 and none(1) if no Authorization Invalid message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.7 and 4.2.2.15." ::= { docsBpi2CmBaseEntry 24 } docsBpi2CmAuthInvalidErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the text string in the most recent Authorization Invalid message received by the CM. This is a zero length string if no Authorization Invalid message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.7 and 4.2.2.6." ::= { docsBpi2CmBaseEntry 25 } -- -- The CM TEK Table, indexed by ifIndex and SAID -- docsBpi2CmTEKTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmTEKEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the attributes of each CM Traffic Encryption Key (TEK) association. The CM maintains (no more than) one TEK association per SAID per CM MAC interface." ::= { docsBpi2CmObjects 2 } docsBpi2CmTEKEntry OBJECT-TYPE SYNTAX DocsBpi2CmTEKEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing the TEK association attributes of one SAID. The CM MUST create one entry per SAID, regardless of whether the SAID was obtained from a Registration Response message, from an Authorization Reply message, or from any dynamic SAID establishment mechanisms." INDEX { ifIndex, docsBpi2CmTEKSAId } ::= { docsBpi2CmTEKTable 1 } DocsBpi2CmTEKEntry ::= SEQUENCE { docsBpi2CmTEKSAId DocsSAId, docsBpi2CmTEKSAType DocsBpkmSAType, docsBpi2CmTEKDataEncryptAlg DocsBpkmDataEncryptAlg, docsBpi2CmTEKDataAuthentAlg DocsBpkmDataAuthentAlg, docsBpi2CmTEKState INTEGER, docsBpi2CmTEKKeySequenceNumber Integer32, docsBpi2CmTEKExpiresOld DateAndTime, docsBpi2CmTEKExpiresNew DateAndTime, docsBpi2CmTEKKeyRequests Counter32, docsBpi2CmTEKKeyReplies Counter32, docsBpi2CmTEKKeyRejects Counter32, docsBpi2CmTEKInvalids Counter32, docsBpi2CmTEKAuthPends Counter32, docsBpi2CmTEKKeyRejectErrorCode INTEGER, docsBpi2CmTEKKeyRejectErrorString SnmpAdminString, docsBpi2CmTEKInvalidErrorCode INTEGER, docsBpi2CmTEKInvalidErrorString SnmpAdminString } docsBpi2CmTEKSAId OBJECT-TYPE SYNTAX DocsSAId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object is the DOCSIS Security Association ID (SAID)." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.12." ::= { docsBpi2CmTEKEntry 1 } docsBpi2CmTEKSAType OBJECT-TYPE SYNTAX DocsBpkmSAType MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the type of security association." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 2.1.3." ::= { docsBpi2CmTEKEntry 2 } docsBpi2CmTEKDataEncryptAlg OBJECT-TYPE SYNTAX DocsBpkmDataEncryptAlg MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data encryption algorithm for this SAID." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.20." ::= { docsBpi2CmTEKEntry 3 } docsBpi2CmTEKDataAuthentAlg OBJECT-TYPE SYNTAX DocsBpkmDataAuthentAlg MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data authentication algorithm for this SAID." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.20." ::= { docsBpi2CmTEKEntry 4 } docsBpi2CmTEKState OBJECT-TYPE SYNTAX INTEGER { start(1), opWait(2), opReauthWait(3), operational(4), rekeyWait(5), rekeyReauthWait(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the state of the indicated TEK FSM. The start(1) state indicates that the FSM is in its initial state." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.1.3.1." ::= { docsBpi2CmTEKEntry 5 } docsBpi2CmTEKKeySequenceNumber OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the most recent TEK key sequence number for this TEK FSM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.2.10 and 4.2.2.13." ::= { docsBpi2CmTEKEntry 6 } docsBpi2CmTEKExpiresOld OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the immediate predecessor of the most recent TEK for this FSM. If this FSM has only one TEK, then the value is the time of activation of this FSM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.5 and 4.2.2.9." ::= { docsBpi2CmTEKEntry 7 } docsBpi2CmTEKExpiresNew OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the most recent TEK for this FSM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.5 and 4.2.2.9." ::= { docsBpi2CmTEKEntry 8 } docsBpi2CmTEKKeyRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has transmitted a Key Request message. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.4." ::= { docsBpi2CmTEKEntry 9 } docsBpi2CmTEKKeyReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has received a Key Reply message, including a message whose authentication failed. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.5." ::= { docsBpi2CmTEKEntry 10 } docsBpi2CmTEKKeyRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has received a Key Reject message, including a message whose authentication failed. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.6." ::= { docsBpi2CmTEKEntry 11 } docsBpi2CmTEKInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has received a TEK Invalid message, including a message whose authentication failed. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.8." ::= { docsBpi2CmTEKEntry 12 } docsBpi2CmTEKAuthPends OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times an Authorization Pending (Auth Pend) event occurred in this FSM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.1.3.3.3." ::= { docsBpi2CmTEKEntry 13 } docsBpi2CmTEKKeyRejectErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedSaid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent Key Reject message received by the CM. This has the value unknown(2) if the last Error-Code value was 0 and none(1) if no Key Reject message has been received since registration." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.1.2.6 and 4.2.2.15." ::= { docsBpi2CmTEKEntry 14 } docsBpi2CmTEKKeyRejectErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the text string in the most recent Key Reject message received by the CM. This is a zero length string if no Key Reject message has been received since registration." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.1.2.6 and 4.2.2.6." ::= { docsBpi2CmTEKEntry 15 } docsBpi2CmTEKInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), invalidKeySequence(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent TEK Invalid message received by the CM. This has the value unknown(2) if the last Error-Code value was 0 and none(1) if no TEK Invalid message has been received since registration." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.1.2.8 and 4.2.2.15." ::= { docsBpi2CmTEKEntry 16 } docsBpi2CmTEKInvalidErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the text string in the most recent TEK Invalid message received by the CM. This is a zero length string if no TEK Invalid message has been received since registration." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.1.2.8 and 4.2.2.6." ::= { docsBpi2CmTEKEntry 17 } -- -- The CM Multicast Objects Group -- docsBpi2CmMulticastObjects OBJECT IDENTIFIER ::= { docsBpi2CmObjects 3 } -- -- The CM Dynamic IP Multicast Mapping Table, indexed by -- docsBpi2CmIpMulticastIndex and by ifIndex -- docsBpi2CmIpMulticastMapTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmIpMulticastMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table maps multicast IP addresses to SAIDs per CM MAC Interface. It is intended to map multicast IP addresses associated with SA MAP Request messages." ::= { docsBpi2CmMulticastObjects 1 } docsBpi2CmIpMulticastMapEntry OBJECT-TYPE SYNTAX DocsBpi2CmIpMulticastMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing the mapping of one multicast IP address to one SAID, as well as associated state, message counters, and error information. An entry may be removed from this table upon the reception of an SA Map Reject." INDEX { ifIndex, docsBpi2CmIpMulticastIndex } ::= { docsBpi2CmIpMulticastMapTable 1 } DocsBpi2CmIpMulticastMapEntry ::= SEQUENCE { docsBpi2CmIpMulticastIndex Unsigned32, docsBpi2CmIpMulticastAddressType InetAddressType, docsBpi2CmIpMulticastAddress InetAddress, docsBpi2CmIpMulticastSAId DocsSAIdOrZero, docsBpi2CmIpMulticastSAMapState INTEGER, docsBpi2CmIpMulticastSAMapRequests Counter32, docsBpi2CmIpMulticastSAMapReplies Counter32, docsBpi2CmIpMulticastSAMapRejects Counter32, docsBpi2CmIpMulticastSAMapRejectErrorCode INTEGER, docsBpi2CmIpMulticastSAMapRejectErrorString SnmpAdminString } docsBpi2CmIpMulticastIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this row." ::= { docsBpi2CmIpMulticastMapEntry 1 } docsBpi2CmIpMulticastAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of Internet address for docsBpi2CmIpMulticastAddress." ::= { docsBpi2CmIpMulticastMapEntry 2 } docsBpi2CmIpMulticastAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the IP multicast address to be mapped. The type of this address is determined by the value of the docsBpi2CmIpMulticastAddressType object." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 5.4." ::= { docsBpi2CmIpMulticastMapEntry 3 } docsBpi2CmIpMulticastSAId OBJECT-TYPE SYNTAX DocsSAIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the SAID to which the IP multicast address has been mapped. If no SA Map Reply has been received for the IP address, this object should have the value 0." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.12." ::= { docsBpi2CmIpMulticastMapEntry 4 } docsBpi2CmIpMulticastSAMapState OBJECT-TYPE SYNTAX INTEGER { start(1), mapWait(2), mapped(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the state of the SA Mapping FSM for this IP." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 5.3.1." ::= { docsBpi2CmIpMulticastMapEntry 5 } docsBpi2CmIpMulticastSAMapRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has transmitted an SA Map Request message for this IP. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.10." ::= { docsBpi2CmIpMulticastMapEntry 6 } docsBpi2CmIpMulticastSAMapReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has received an SA Map Reply message for this IP. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.11." ::= { docsBpi2CmIpMulticastMapEntry 7 } docsBpi2CmIpMulticastSAMapRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CM has received an SA MAP Reject message for this IP. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.12." ::= { docsBpi2CmIpMulticastMapEntry 8 } docsBpi2CmIpMulticastSAMapRejectErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), noAuthForRequestedDSFlow(9), dsFlowNotMappedToSA(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent SA Map Reject message sent in response to an SA Map Request for This IP. It has the value none(1) if no SA MAP Reject message has been received since entry creation." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.12 and 4.2.2.15." ::= { docsBpi2CmIpMulticastMapEntry 9 } docsBpi2CmIpMulticastSAMapRejectErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the text string in the most recent SA Map Reject message sent in response to an SA Map Request for this IP. It is a zero length string if no SA Map Reject message has been received since entry creation." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.12 and 4.2.2.6." ::= { docsBpi2CmIpMulticastMapEntry 10 } -- -- CM Cert Objects -- docsBpi2CmCertObjects OBJECT IDENTIFIER ::= { docsBpi2CmObjects 4 } -- -- CM Device Cert Table -- docsBpi2CmDeviceCertTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmDeviceCertEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the Baseline Privacy Plus device certificates for each CM MAC interface." ::= { docsBpi2CmCertObjects 1 } docsBpi2CmDeviceCertEntry OBJECT-TYPE SYNTAX DocsBpi2CmDeviceCertEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the device certificates of one CM MAC interface. An entry in this table exists for each ifEntry with an ifType of docsCableMaclayer(127)." INDEX { ifIndex } ::= { docsBpi2CmDeviceCertTable 1 } DocsBpi2CmDeviceCertEntry ::= SEQUENCE { docsBpi2CmDeviceCmCert DocsX509ASN1DEREncodedCertificate, docsBpi2CmDeviceManufCert DocsX509ASN1DEREncodedCertificate } docsBpi2CmDeviceCmCert OBJECT-TYPE SYNTAX DocsX509ASN1DEREncodedCertificate MAX-ACCESS read-write STATUS current DESCRIPTION "The X509 DER-encoded cable modem certificate. Note: This object can be set only when the value is the zero-length OCTET STRING; otherwise, an error of 'inconsistentValue' is returned. Once the object contains the certificate, its access MUST be read-only and persists after re-initialization of the managed system." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.1." ::= { docsBpi2CmDeviceCertEntry 1 } docsBpi2CmDeviceManufCert OBJECT-TYPE SYNTAX DocsX509ASN1DEREncodedCertificate MAX-ACCESS read-only STATUS current DESCRIPTION "The X509 DER-encoded manufacturer certificate that signed the cable modem certificate." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.1." ::= { docsBpi2CmDeviceCertEntry 2 } -- -- CM Crypto Suite Table -- docsBpi2CmCryptoSuiteTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmCryptoSuiteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the Baseline Privacy Plus cryptographic suite capabilities for each CM MAC interface." ::= { docsBpi2CmObjects 5 } docsBpi2CmCryptoSuiteEntry OBJECT-TYPE SYNTAX DocsBpi2CmCryptoSuiteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains a cryptographic suite pair that this CM MAC supports." INDEX { ifIndex, docsBpi2CmCryptoSuiteIndex } ::= { docsBpi2CmCryptoSuiteTable 1 } DocsBpi2CmCryptoSuiteEntry ::= SEQUENCE { docsBpi2CmCryptoSuiteIndex Unsigned32, docsBpi2CmCryptoSuiteDataEncryptAlg DocsBpkmDataEncryptAlg, docsBpi2CmCryptoSuiteDataAuthentAlg DocsBpkmDataAuthentAlg } docsBpi2CmCryptoSuiteIndex OBJECT-TYPE SYNTAX Unsigned32 (1..1000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for a cryptographic suite row." ::= { docsBpi2CmCryptoSuiteEntry 1 } docsBpi2CmCryptoSuiteDataEncryptAlg OBJECT-TYPE SYNTAX DocsBpkmDataEncryptAlg MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data encryption algorithm for this cryptographic suite capability." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.20." ::= { docsBpi2CmCryptoSuiteEntry 2 } docsBpi2CmCryptoSuiteDataAuthentAlg OBJECT-TYPE SYNTAX DocsBpkmDataAuthentAlg MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data authentication algorithm for this cryptographic suite capability." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.20." ::= { docsBpi2CmCryptoSuiteEntry 3 } -- Cable Modem Termination System Group docsBpi2CmtsObjects OBJECT IDENTIFIER ::= { docsBpi2MIBObjects 2 } -- -- SPECIAL NOTE: For the following CMTS tables, when a CM is -- running in BPI mode, replace SAID (Security Association ID) -- with SID (Service ID). The CMTS is required to map SAIDs and -- SIDs to one contiguous space. -- -- -- The BPI+ base table for CMTSs, indexed by ifIndex -- docsBpi2CmtsBaseTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmtsBaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the basic Baseline Privacy attributes of each CMTS MAC interface." ::= { docsBpi2CmtsObjects 1 } docsBpi2CmtsBaseEntry OBJECT-TYPE SYNTAX DocsBpi2CmtsBaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing attributes of one CMTS MAC interface. An entry in this table exists for each ifEntry with an ifType of docsCableMaclayer(127)." INDEX { ifIndex } ::= { docsBpi2CmtsBaseTable 1 } DocsBpi2CmtsBaseEntry ::= SEQUENCE { docsBpi2CmtsDefaultAuthLifetime Integer32, docsBpi2CmtsDefaultTEKLifetime Integer32, docsBpi2CmtsDefaultSelfSignedManufCertTrust INTEGER, docsBpi2CmtsCheckCertValidityPeriods TruthValue, docsBpi2CmtsAuthentInfos Counter32, docsBpi2CmtsAuthRequests Counter32, docsBpi2CmtsAuthReplies Counter32, docsBpi2CmtsAuthRejects Counter32, docsBpi2CmtsAuthInvalids Counter32, docsBpi2CmtsSAMapRequests Counter32, docsBpi2CmtsSAMapReplies Counter32, docsBpi2CmtsSAMapRejects Counter32 } docsBpi2CmtsDefaultAuthLifetime OBJECT-TYPE SYNTAX Integer32 (1..6048000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the default lifetime, in seconds, that the CMTS assigns to a new authorization key. This object value persists after re-initialization of the managed system." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.2." DEFVAL { 604800 } ::= { docsBpi2CmtsBaseEntry 1 } docsBpi2CmtsDefaultTEKLifetime OBJECT-TYPE SYNTAX Integer32 (1..604800) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the default lifetime, in seconds, that the CMTS assigns to a new Traffic Encryption Key (TEK). This object value persists after re-initialization of the managed system." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Appendix A.2." DEFVAL { 43200 } ::= { docsBpi2CmtsBaseEntry 2 } docsBpi2CmtsDefaultSelfSignedManufCertTrust OBJECT-TYPE SYNTAX INTEGER { trusted (1), untrusted (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object determines the default trust of self-signed manufacturer certificate entries, contained in docsBpi2CmtsCACertTable, and created after this object is set. This object need not persist after re-initialization of the managed system." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.4.1" ::= { docsBpi2CmtsBaseEntry 3 } docsBpi2CmtsCheckCertValidityPeriods OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'true' causes all chained and root certificates in the chain to have their validity periods checked against the current time of day, when the CMTS receives an Authorization Request from the CM. A 'false' setting causes all certificates in the chain not to have their validity periods checked against the current time of day. This object need not persist after re-initialization of the managed system." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.4.2" ::= { docsBpi2CmtsBaseEntry 4 } docsBpi2CmtsAuthentInfos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has received an Authentication Information message from any CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.9." ::= { docsBpi2CmtsBaseEntry 5 } docsBpi2CmtsAuthRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has received an Authorization Request message from any CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.1." ::= { docsBpi2CmtsBaseEntry 6 } docsBpi2CmtsAuthReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted an Authorization Reply message to any CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.2." ::= { docsBpi2CmtsBaseEntry 7 } docsBpi2CmtsAuthRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted an Authorization Reject message to any CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.3." ::= { docsBpi2CmtsBaseEntry 8 } docsBpi2CmtsAuthInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted an Authorization Invalid message to any CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.7." ::= { docsBpi2CmtsBaseEntry 9 } docsBpi2CmtsSAMapRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has received an SA Map Request message from any CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.10." ::= { docsBpi2CmtsBaseEntry 10 } docsBpi2CmtsSAMapReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted an SA Map Reply message to any CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.11." ::= { docsBpi2CmtsBaseEntry 11 } docsBpi2CmtsSAMapRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted an SA Map Reject message to any CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.12." ::= { docsBpi2CmtsBaseEntry 12 } -- -- The CMTS Authorization Table, indexed by ifIndex and CM MAC -- address -- docsBpi2CmtsAuthTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmtsAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the attributes of each CM authorization association. The CMTS maintains one authorization association with each Baseline Privacy- enabled CM, registered on each CMTS MAC interface, regardless of whether the CM is authorized or rejected." ::= { docsBpi2CmtsObjects 2 } docsBpi2CmtsAuthEntry OBJECT-TYPE SYNTAX DocsBpi2CmtsAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing attributes of one authorization association. The CMTS MUST create one entry per CM per MAC interface, based on the receipt of an Authorization Request message, and MUST not delete the entry until the CM loses registration." INDEX { ifIndex, docsBpi2CmtsAuthCmMacAddress } ::= { docsBpi2CmtsAuthTable 1 } DocsBpi2CmtsAuthEntry ::= SEQUENCE { docsBpi2CmtsAuthCmMacAddress MacAddress, docsBpi2CmtsAuthCmBpiVersion INTEGER, docsBpi2CmtsAuthCmPublicKey OCTET STRING, docsBpi2CmtsAuthCmKeySequenceNumber Integer32, docsBpi2CmtsAuthCmExpiresOld DateAndTime, docsBpi2CmtsAuthCmExpiresNew DateAndTime, docsBpi2CmtsAuthCmLifetime Integer32, docsBpi2CmtsAuthCmReset INTEGER, docsBpi2CmtsAuthCmInfos Counter32, docsBpi2CmtsAuthCmRequests Counter32, docsBpi2CmtsAuthCmReplies Counter32, docsBpi2CmtsAuthCmRejects Counter32, docsBpi2CmtsAuthCmInvalids Counter32, docsBpi2CmtsAuthRejectErrorCode INTEGER, docsBpi2CmtsAuthRejectErrorString SnmpAdminString, docsBpi2CmtsAuthInvalidErrorCode INTEGER, docsBpi2CmtsAuthInvalidErrorString SnmpAdminString, docsBpi2CmtsAuthPrimarySAId DocsSAIdOrZero, docsBpi2CmtsAuthBpkmCmCertValid INTEGER, docsBpi2CmtsAuthBpkmCmCert DocsX509ASN1DEREncodedCertificate, docsBpi2CmtsAuthCACertIndexPtr Unsigned32 } docsBpi2CmtsAuthCmMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object is the physical address of the CM to which the authorization association applies." ::= { docsBpi2CmtsAuthEntry 1 } docsBpi2CmtsAuthCmBpiVersion OBJECT-TYPE SYNTAX INTEGER { bpi (0), bpiPlus (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the version of Baseline Privacy for which this CM has registered. The value 'bpiplus' represents the value of BPI-Version Attribute of the Baseline Privacy Key Management BPKM attribute BPI-Version (1). The value 'bpi' is used to represent the CM registered using DOCSIS 1.0 Baseline Privacy." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.22; ANSI/SCTE 22-2 2002(formerly DSS 02-03) Data-Over-Cable Service Interface Specification DOCSIS 1.0 Baseline Privacy Interface (BPI)" ::= { docsBpi2CmtsAuthEntry 2 } docsBpi2CmtsAuthCmPublicKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..524)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is a DER-encoded RSAPublicKey ASN.1 type string, as defined in the RSA Encryption Standard (PKCS #1), corresponding to the public key of the CM. This is the zero-length OCTET STRING if the CMTS does not retain the public key." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.4." ::= { docsBpi2CmtsAuthEntry 3 } docsBpi2CmtsAuthCmKeySequenceNumber OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the most recent authorization key sequence number for this CM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.2 and 4.2.2.10." ::= { docsBpi2CmtsAuthEntry 4 } docsBpi2CmtsAuthCmExpiresOld OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the immediate predecessor of the most recent authorization key for this FSM. If this FSM has only one authorization key, then the value is the time of activation of this FSM. Note: This object has no meaning for CMs running in BPI mode; therefore, this object is not instantiated for entries associated to those CMs." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.2 and 4.2.2.9." ::= { docsBpi2CmtsAuthEntry 5 } docsBpi2CmtsAuthCmExpiresNew OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the most recent authorization key for this FSM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.2 and 4.2.2.9." ::= { docsBpi2CmtsAuthEntry 6 } docsBpi2CmtsAuthCmLifetime OBJECT-TYPE SYNTAX Integer32 (1..6048000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the lifetime, in seconds, that the CMTS assigns to an authorization key for this CM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.2 and Appendix A.2." ::= { docsBpi2CmtsAuthEntry 7 } docsBpi2CmtsAuthCmReset OBJECT-TYPE SYNTAX INTEGER { noResetRequested(1), invalidateAuth(2), sendAuthInvalid(3), invalidateTeks(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to invalidateAuth(2) causes the CMTS to invalidate the current CM authorization key(s), but not to transmit an Authorization Invalid message nor to invalidate the primary SAID's TEKs. Setting this object to sendAuthInvalid(3) causes the CMTS to invalidate the current CM authorization key(s), and to transmit an Authorization Invalid message to the CM, but not to invalidate the primary SAID's TEKs. Setting this object to invalidateTeks(4) causes the CMTS to invalidate the current CM authorization key(s), to transmit an Authorization Invalid message to the CM, and to invalidate the TEKs associated with this CM's primary SAID. For BPI mode, substitute all of the CM's unicast TEKs for the primary SAID's TEKs in the previous paragraph. Reading this object returns the most recently set value of this object or, if the object has not been set since entry creation, returns noResetRequested(1)." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.1.2.3.4, 4.1.2.3.5, and 4.1.3.3.5." ::= { docsBpi2CmtsAuthEntry 8 } docsBpi2CmtsAuthCmInfos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has received an Authentication Information message from this CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.9." ::= { docsBpi2CmtsAuthEntry 9 } docsBpi2CmtsAuthCmRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has received an Authorization Request message from this CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.1." ::= { docsBpi2CmtsAuthEntry 10 } docsBpi2CmtsAuthCmReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted an Authorization Reply message to this CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.2." ::= { docsBpi2CmtsAuthEntry 11 } docsBpi2CmtsAuthCmRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted an Authorization Reject message to this CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.3." ::= { docsBpi2CmtsAuthEntry 12 } docsBpi2CmtsAuthCmInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted an Authorization Invalid message to this CM. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.7." ::= { docsBpi2CmtsAuthEntry 13 } docsBpi2CmtsAuthRejectErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedCm(3), unauthorizedSaid(4), permanentAuthorizationFailure(8), timeOfDayNotAcquired(11) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent Authorization Reject message transmitted to the CM. This has the value unknown(2) if the last Error-Code value was 0 and none(1) if no Authorization Reject message has been transmitted to the CM since entry creation." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.3 and 4.2.2.15." ::= { docsBpi2CmtsAuthEntry 14 } docsBpi2CmtsAuthRejectErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the text string in the most recent Authorization Reject message transmitted to the CM. This is a zero length string if no Authorization Reject message has been transmitted to the CM since entry creation." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.3 and 4.2.2.6." ::= { docsBpi2CmtsAuthEntry 15 } docsBpi2CmtsAuthInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedCm(3), unsolicited(5), invalidKeySequence(6), keyRequestAuthenticationFailure(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent Authorization Invalid message transmitted to the CM. This has the value unknown(2) if the last Error-Code value was 0 and none(1) if no Authorization Invalid message has been transmitted to the CM since entry creation." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.7 and 4.2.2.15." ::= { docsBpi2CmtsAuthEntry 16 } docsBpi2CmtsAuthInvalidErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the text string in the most recent Authorization Invalid message transmitted to the CM. This is a zero length string if no Authorization Invalid message has been transmitted to the CM since entry creation." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.7 and 4.2.2.6." ::= { docsBpi2CmtsAuthEntry 17 } docsBpi2CmtsAuthPrimarySAId OBJECT-TYPE SYNTAX DocsSAIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Primary Security Association identifier. For BPI mode, the value must be any unicast SID." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 2.1.3." ::= { docsBpi2CmtsAuthEntry 18 } docsBpi2CmtsAuthBpkmCmCertValid OBJECT-TYPE SYNTAX INTEGER { unknown (0), validCmChained (1), validCmTrusted (2), invalidCmUntrusted (3), invalidCAUntrusted (4), invalidCmOther (5), invalidCAOther (6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the reason why a CM's certificate is deemed valid or invalid. Return unknown(0) if the CM is running BPI mode. ValidCmChained(1) means the certificate is valid because it chains to a valid certificate. ValidCmTrusted(2) means the certificate is valid because it has been provisioned (in the docsBpi2CmtsProvisionedCmCert table) to be trusted. InvalidCmUntrusted(3) means the certificate is invalid because it has been provisioned (in the docsBpi2CmtsProvisionedCmCert table) to be untrusted. InvalidCAUntrusted(4) means the certificate is invalid because it chains to an untrusted certificate. InvalidCmOther(5) and InvalidCAOther(6) refer to errors in parsing, validity periods, etc., which are attributable to the CM certificate or its chain, respectively; additional information may be found in docsBpi2AuthRejectErrorString for these types of errors." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.4.2." ::= { docsBpi2CmtsAuthEntry 19 } docsBpi2CmtsAuthBpkmCmCert OBJECT-TYPE SYNTAX DocsX509ASN1DEREncodedCertificate MAX-ACCESS read-only STATUS current DESCRIPTION "The X509 CM Certificate sent as part of a BPKM Authorization Request. Note: The zero-length OCTET STRING must be returned if the Entire certificate is not retained in the CMTS." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.2." ::= { docsBpi2CmtsAuthEntry 20 } docsBpi2CmtsAuthCACertIndexPtr OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "A row index into docsBpi2CmtsCACertTable. Returns the index in docsBpi2CmtsCACertTable to which CA certificate this CM is chained to. A value of 0 means it could not be found or not applicable." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.2." ::= { docsBpi2CmtsAuthEntry 21 } -- -- The CMTS TEK Table, indexed by ifIndex and SAID -- docsBpi2CmtsTEKTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmtsTEKEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the attributes of each Traffic Encryption Key (TEK) association. The CMTS Maintains one TEK association per SAID on each CMTS MAC interface." ::= { docsBpi2CmtsObjects 3 } docsBpi2CmtsTEKEntry OBJECT-TYPE SYNTAX DocsBpi2CmtsTEKEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing attributes of one TEK association on a particular CMTS MAC interface. The CMTS MUST create one entry per SAID per MAC interface, based on the receipt of a Key Request message, and MUST not delete the entry before the CM authorization for the SAID permanently expires." INDEX { ifIndex, docsBpi2CmtsTEKSAId } ::= { docsBpi2CmtsTEKTable 1 } DocsBpi2CmtsTEKEntry ::= SEQUENCE { docsBpi2CmtsTEKSAId DocsSAId, docsBpi2CmtsTEKSAType DocsBpkmSAType, docsBpi2CmtsTEKDataEncryptAlg DocsBpkmDataEncryptAlg, docsBpi2CmtsTEKDataAuthentAlg DocsBpkmDataAuthentAlg, docsBpi2CmtsTEKLifetime Integer32, docsBpi2CmtsTEKKeySequenceNumber Integer32, docsBpi2CmtsTEKExpiresOld DateAndTime, docsBpi2CmtsTEKExpiresNew DateAndTime, docsBpi2CmtsTEKReset TruthValue, docsBpi2CmtsKeyRequests Counter32, docsBpi2CmtsKeyReplies Counter32, docsBpi2CmtsKeyRejects Counter32, docsBpi2CmtsTEKInvalids Counter32, docsBpi2CmtsKeyRejectErrorCode INTEGER, docsBpi2CmtsKeyRejectErrorString SnmpAdminString, docsBpi2CmtsTEKInvalidErrorCode INTEGER, docsBpi2CmtsTEKInvalidErrorString SnmpAdminString } docsBpi2CmtsTEKSAId OBJECT-TYPE SYNTAX DocsSAId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object is the DOCSIS Security Association ID (SAID)." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.12." ::= { docsBpi2CmtsTEKEntry 1 } docsBpi2CmtsTEKSAType OBJECT-TYPE SYNTAX DocsBpkmSAType MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the type of security association. 'dynamic' does not apply to CMs running in BPI mode. Unicast BPI TEKs must utilize the 'primary' encoding, and multicast BPI TEKs must utilize the 'static' encoding." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 2.1.3." ::= { docsBpi2CmtsTEKEntry 2 } docsBpi2CmtsTEKDataEncryptAlg OBJECT-TYPE SYNTAX DocsBpkmDataEncryptAlg MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data encryption algorithm for this SAID." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.20." ::= { docsBpi2CmtsTEKEntry 3 } docsBpi2CmtsTEKDataAuthentAlg OBJECT-TYPE SYNTAX DocsBpkmDataAuthentAlg MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the data authentication algorithm for this SAID." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.20." ::= { docsBpi2CmtsTEKEntry 4 } docsBpi2CmtsTEKLifetime OBJECT-TYPE SYNTAX Integer32 (1..604800) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the lifetime, in seconds, that the CMTS assigns to keys for this TEK association." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.5 and Appendix A.2." ::= { docsBpi2CmtsTEKEntry 5 } docsBpi2CmtsTEKKeySequenceNumber OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the most recent TEK key sequence number for this SAID." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.2.10 and 4.2.2.13." ::= { docsBpi2CmtsTEKEntry 6 } docsBpi2CmtsTEKExpiresOld OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the immediate predecessor of the most recent TEK for this FSM. If this FSM has only one TEK, then the value is the time of activation of this FSM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.5 and 4.2.2.9." ::= { docsBpi2CmtsTEKEntry 7 } docsBpi2CmtsTEKExpiresNew OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the most recent TEK for this FSM." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.5 and 4.2.2.9." ::= { docsBpi2CmtsTEKEntry 8 } docsBpi2CmtsTEKReset OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'true' causes the CMTS to invalidate all currently active TEKs and to generate new TEKs for the associated SAID; the CMTS MAY also generate unsolicited TEK Invalid messages, to optimize the TEK synchronization between the CMTS and the CM(s). Reading this object always returns FALSE." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.1.3.3.5." ::= { docsBpi2CmtsTEKEntry 9 } docsBpi2CmtsKeyRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has received a Key Request message. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.4." ::= { docsBpi2CmtsTEKEntry 10 } docsBpi2CmtsKeyReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted a Key Reply message. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.5." ::= { docsBpi2CmtsTEKEntry 11 } docsBpi2CmtsKeyRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted a Key Reject message. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.6." ::= { docsBpi2CmtsTEKEntry 12 } docsBpi2CmtsTEKInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted a TEK Invalid message. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.8." ::= { docsBpi2CmtsTEKEntry 13 } docsBpi2CmtsKeyRejectErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedSaid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent Key Reject message sent in response to a Key Request for this SAID. This has the value unknown(2) if the last Error-Code value was 0 and none(1) if no Key Reject message has been received since registration." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.6 and 4.2.2.15." ::= { docsBpi2CmtsTEKEntry 14 } docsBpi2CmtsKeyRejectErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the text string in the most recent Key Reject message sent in response to a Key Request for this SAID. This is a zero length string if no Key Reject message has been received since registration." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.6 and 4.2.2.6." ::= { docsBpi2CmtsTEKEntry 15 } docsBpi2CmtsTEKInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), invalidKeySequence(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent TEK Invalid message sent in association with this SAID. This has the value unknown(2) if the last Error-Code value was 0 and none(1) if no TEK Invalid message has been received since registration." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.8 and 4.2.2.15." ::= { docsBpi2CmtsTEKEntry 16 } docsBpi2CmtsTEKInvalidErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the text string in the most recent TEK Invalid message sent in association with this SAID. This is a zero length string if no TEK Invalid message has been received since registration." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.8 and 4.2.2.6." ::= { docsBpi2CmtsTEKEntry 17 } -- -- The CMTS Multicast Objects Group -- docsBpi2CmtsMulticastObjects OBJECT IDENTIFIER ::= { docsBpi2CmtsObjects 4 } -- -- The CMTS IP Multicast Mapping Table, indexed by -- docsBpi2CmtsIpMulticastIndex, and by ifIndex -- docsBpi2CmtsIpMulticastMapTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmtsIpMulticastMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table maps multicast IP addresses to SAIDs. If a multicast IP address is mapped by multiple rows in the table, the row with the lowest docsBpi2CmtsIpMulticastIndex must be utilized for the mapping." ::= { docsBpi2CmtsMulticastObjects 1 } docsBpi2CmtsIpMulticastMapEntry OBJECT-TYPE SYNTAX DocsBpi2CmtsIpMulticastMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing the mapping of a set of multicast IP address and the mask to one SAID associated to a CMTS MAC Interface, as well as associated message counters and error information." INDEX { ifIndex, docsBpi2CmtsIpMulticastIndex } ::= { docsBpi2CmtsIpMulticastMapTable 1 } DocsBpi2CmtsIpMulticastMapEntry ::= SEQUENCE { docsBpi2CmtsIpMulticastIndex Unsigned32, docsBpi2CmtsIpMulticastAddressType InetAddressType, docsBpi2CmtsIpMulticastAddress InetAddress, docsBpi2CmtsIpMulticastMask InetAddress, docsBpi2CmtsIpMulticastSAId DocsSAIdOrZero, docsBpi2CmtsIpMulticastSAType DocsBpkmSAType, docsBpi2CmtsIpMulticastDataEncryptAlg DocsBpkmDataEncryptAlg, docsBpi2CmtsIpMulticastDataAuthentAlg DocsBpkmDataAuthentAlg, docsBpi2CmtsIpMulticastSAMapRequests Counter32, docsBpi2CmtsIpMulticastSAMapReplies Counter32, docsBpi2CmtsIpMulticastSAMapRejects Counter32, docsBpi2CmtsIpMulticastSAMapRejectErrorCode INTEGER, docsBpi2CmtsIpMulticastSAMapRejectErrorString SnmpAdminString, docsBpi2CmtsIpMulticastMapControl RowStatus, docsBpi2CmtsIpMulticastMapStorageType StorageType } docsBpi2CmtsIpMulticastIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row." ::= { docsBpi2CmtsIpMulticastMapEntry 1 } docsBpi2CmtsIpMulticastAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of Internet address for docsBpi2CmtsIpMulticastAddress and docsBpi2CmtsIpMulticastMask." DEFVAL { ipv4 } ::= { docsBpi2CmtsIpMulticastMapEntry 2 } docsBpi2CmtsIpMulticastAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the IP multicast address to be mapped, in conjunction with docsBpi2CmtsIpMulticastMask. The type of this address is determined by the value of the object docsBpi2CmtsIpMulticastAddressType." ::= { docsBpi2CmtsIpMulticastMapEntry 3 } docsBpi2CmtsIpMulticastMask OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the IP multicast address mask for this row. An IP multicast address matches this row if the logical AND of the address with docsBpi2CmtsIpMulticastMask is identical to the logical AND of docsBpi2CmtsIpMulticastAddr with docsBpi2CmtsIpMulticastMask. The type of this address is determined by the value of the object docsBpi2CmtsIpMulticastAddressType. Note: For IPv6, this object need not represent a contiguous netmask; e.g., to associate a SAID to a multicast group matching 'any' multicast scope. The TC InetAddressPrefixLength is not used, as it only represents contiguous netmask." ::= { docsBpi2CmtsIpMulticastMapEntry 4 } docsBpi2CmtsIpMulticastSAId OBJECT-TYPE SYNTAX DocsSAIdOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the multicast SAID to be used in this IP multicast address mapping entry." ::= { docsBpi2CmtsIpMulticastMapEntry 5 } docsBpi2CmtsIpMulticastSAType OBJECT-TYPE SYNTAX DocsBpkmSAType MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object is the type of security association. 'dynamic' does not apply to CMs running in BPI mode. Unicast BPI TEKs must utilize the 'primary' encoding, and multicast BPI TEKs must utilize the 'static' encoding. By default, SNMP created entries set this object to 'static' if not set at row creation." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 2.1.3." ::= { docsBpi2CmtsIpMulticastMapEntry 6 } docsBpi2CmtsIpMulticastDataEncryptAlg OBJECT-TYPE SYNTAX DocsBpkmDataEncryptAlg MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object is the data encryption algorithm for this IP." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.20." DEFVAL { des56CbcMode } ::= { docsBpi2CmtsIpMulticastMapEntry 7 } docsBpi2CmtsIpMulticastDataAuthentAlg OBJECT-TYPE SYNTAX DocsBpkmDataAuthentAlg MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object is the data authentication algorithm for this IP." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.2.20." DEFVAL { none } ::= { docsBpi2CmtsIpMulticastMapEntry 8 } docsBpi2CmtsIpMulticastSAMapRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has received an SA Map Request message for this IP. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.10." ::= { docsBpi2CmtsIpMulticastMapEntry 9 } docsBpi2CmtsIpMulticastSAMapReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted an SA Map Reply message for this IP. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.11." ::= { docsBpi2CmtsIpMulticastMapEntry 10 } docsBpi2CmtsIpMulticastSAMapRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of times the CMTS has transmitted an SA Map Reject message for this IP. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 4.2.1.12." ::= { docsBpi2CmtsIpMulticastMapEntry 11 } docsBpi2CmtsIpMulticastSAMapRejectErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), noAuthForRequestedDSFlow(9), dsFlowNotMappedToSA(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent SA Map Reject message sent in response to an SA Map Request for this IP. It has the value unknown(2) if the last Error-Code Value was 0 and none(1) if no SA MAP Reject message has been received since entry creation." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.12 and 4.2.2.15." ::= { docsBpi2CmtsIpMulticastMapEntry 12 } docsBpi2CmtsIpMulticastSAMapRejectErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the text string in the most recent SA Map Reject message sent in response to an SA Map Request for this IP. It is a zero length string if no SA Map Reject message has been received since entry creation." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections 4.2.1.12 and 4.2.2.6." ::= { docsBpi2CmtsIpMulticastMapEntry 13 } docsBpi2CmtsIpMulticastMapControl OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object controls and reflects the IP multicast address mapping entry. There is no restriction on the ability to change values in this row while the row is active. A created row can be set to active only after the Corresponding instances of docsBpi2CmtsIpMulticastAddress, docsBpi2CmtsIpMulticastMask, docsBpi2CmtsIpMulticastSAId, and docsBpi2CmtsIpMulticastSAType have all been set." ::= { docsBpi2CmtsIpMulticastMapEntry 14 } docsBpi2CmtsIpMulticastMapStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-only STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row." ::= { docsBpi2CmtsIpMulticastMapEntry 15 } -- -- The CMTS Multicast SAID Authorization Table, -- indexed by ifIndex by -- multicast SAID by CM MAC address -- docsBpi2CmtsMulticastAuthTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmtsMulticastAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the multicast SAID authorization for each CM on each CMTS MAC interface." ::= { docsBpi2CmtsMulticastObjects 2 } docsBpi2CmtsMulticastAuthEntry OBJECT-TYPE SYNTAX DocsBpi2CmtsMulticastAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing the key authorization of one cable modem for one multicast SAID for one CMTS MAC interface. Row entries persist after re-initialization of the managed system." INDEX { ifIndex, docsBpi2CmtsMulticastAuthSAId, docsBpi2CmtsMulticastAuthCmMacAddress } ::= { docsBpi2CmtsMulticastAuthTable 1 } DocsBpi2CmtsMulticastAuthEntry ::= SEQUENCE { docsBpi2CmtsMulticastAuthSAId DocsSAId, docsBpi2CmtsMulticastAuthCmMacAddress MacAddress, docsBpi2CmtsMulticastAuthControl RowStatus } docsBpi2CmtsMulticastAuthSAId OBJECT-TYPE SYNTAX DocsSAId MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the multicast SAID for authorization." ::= { docsBpi2CmtsMulticastAuthEntry 1 } docsBpi2CmtsMulticastAuthCmMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the MAC address of the CM to which the multicast SAID authorization applies." ::= { docsBpi2CmtsMulticastAuthEntry 2 } docsBpi2CmtsMulticastAuthControl OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row for the authorization of multicast SAIDs to CMs." ::= { docsBpi2CmtsMulticastAuthEntry 3 } -- -- CMTS Cert Objects -- docsBpi2CmtsCertObjects OBJECT IDENTIFIER ::= { docsBpi2CmtsObjects 5 } -- -- CMTS Provisioned CM Cert Table -- docsBpi2CmtsProvisionedCmCertTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmtsProvisionedCmCertEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of CM certificate trust entries provisioned to the CMTS. The trust object for a certificate in this table has an overriding effect on the validity object of a certificate in the authorization table, as long as the entire contents of the two certificates are identical." ::= { docsBpi2CmtsCertObjects 1 } docsBpi2CmtsProvisionedCmCertEntry OBJECT-TYPE SYNTAX DocsBpi2CmtsProvisionedCmCertEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the CMTS's provisioned CM certificate table. Row entries persist after re-initialization of the managed system." REFERENCE "Data-Over-Cable Service Interface Specifications: Operations Support System Interface Specification SP-OSSIv2.0-I05-040407, Section 6.2.14" INDEX { docsBpi2CmtsProvisionedCmCertMacAddress } ::= { docsBpi2CmtsProvisionedCmCertTable 1 } DocsBpi2CmtsProvisionedCmCertEntry ::= SEQUENCE { docsBpi2CmtsProvisionedCmCertMacAddress MacAddress, docsBpi2CmtsProvisionedCmCertTrust INTEGER, docsBpi2CmtsProvisionedCmCertSource INTEGER, docsBpi2CmtsProvisionedCmCertStatus RowStatus, docsBpi2CmtsProvisionedCmCert DocsX509ASN1DEREncodedCertificate } docsBpi2CmtsProvisionedCmCertMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this row." ::= { docsBpi2CmtsProvisionedCmCertEntry 1 } docsBpi2CmtsProvisionedCmCertTrust OBJECT-TYPE SYNTAX INTEGER { trusted(1), untrusted(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Trust state for the provisioned CM certificate entry. Note: Setting this object need only override the validity of CM certificates sent in future authorization requests; instantaneous effect need not occur." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.4.1." DEFVAL { untrusted } ::= { docsBpi2CmtsProvisionedCmCertEntry 2 } docsBpi2CmtsProvisionedCmCertSource OBJECT-TYPE SYNTAX INTEGER { snmp(1), configurationFile(2), externalDatabase(3), other(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates how the certificate reached the CMTS. Other(4) means that it originated from a source not identified above." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.4.1." ::= { docsBpi2CmtsProvisionedCmCertEntry 3 } docsBpi2CmtsProvisionedCmCertStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. Values in this row cannot be changed while the row is 'active'." ::= { docsBpi2CmtsProvisionedCmCertEntry 4 } docsBpi2CmtsProvisionedCmCert OBJECT-TYPE SYNTAX DocsX509ASN1DEREncodedCertificate MAX-ACCESS read-create STATUS current DESCRIPTION "An X509 DER-encoded Certificate Authority certificate. Note: The zero-length OCTET STRING must be returned, on reads, if the entire certificate is not retained in the CMTS." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.2." ::= { docsBpi2CmtsProvisionedCmCertEntry 5 } -- -- CMTS CA Cert Table -- docsBpi2CmtsCACertTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpi2CmtsCACertEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of known Certificate Authority certificates acquired by this device." ::= { docsBpi2CmtsCertObjects 2 } docsBpi2CmtsCACertEntry OBJECT-TYPE SYNTAX DocsBpi2CmtsCACertEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Certificate Authority certificate table. Row entries with the trust status 'trusted', 'untrusted', or 'root' persist after re-initialization of the managed system." REFERENCE "Data-Over-Cable Service Interface Specifications: Operations Support System Interface Specification SP-OSSIv2.0-I05-040407, Section 6.2.14" INDEX { docsBpi2CmtsCACertIndex } ::= {docsBpi2CmtsCACertTable 1 } DocsBpi2CmtsCACertEntry ::= SEQUENCE { docsBpi2CmtsCACertIndex Unsigned32, docsBpi2CmtsCACertSubject SnmpAdminString, docsBpi2CmtsCACertIssuer SnmpAdminString, docsBpi2CmtsCACertSerialNumber OCTET STRING, docsBpi2CmtsCACertTrust INTEGER, docsBpi2CmtsCACertSource INTEGER, docsBpi2CmtsCACertStatus RowStatus, docsBpi2CmtsCACert DocsX509ASN1DEREncodedCertificate, docsBpi2CmtsCACertThumbprint OCTET STRING } docsBpi2CmtsCACertIndex OBJECT-TYPE SYNTAX Unsigned32 (1.. 4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for this row." ::= { docsBpi2CmtsCACertEntry 1 } docsBpi2CmtsCACertSubject OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The subject name exactly as it is encoded in the X509 certificate. The organizationName portion of the certificate's subject name must be present. All other fields are optional. Any optional field present must be prepended with <CR> (carriage return, U+000D) <LF> (line feed, U+000A). Ordering of fields present must conform to the following: organizationName <CR> <LF> countryName <CR> <LF> stateOrProvinceName <CR> <LF> localityName <CR> <LF> organizationalUnitName <CR> <LF> organizationalUnitName=<Manufacturing Location> <CR> <LF> commonName" REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.2.4" ::= { docsBpi2CmtsCACertEntry 2 } docsBpi2CmtsCACertIssuer OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The issuer name exactly as it is encoded in the X509 certificate. The commonName portion of the certificate's issuer name must be present. All other fields are optional. Any optional field present must be prepended with <CR> (carriage return, U+000D) <LF> (line feed, U+000A). Ordering of fields present must conform to the following: CommonName <CR><LF> countryName <CR><LF> stateOrProvinceName <CR><LF> localityName <CR><LF> organizationName <CR><LF> organizationalUnitName <CR><LF> organizationalUnitName=<Manufacturing Location>" REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.2.4" ::= { docsBpi2CmtsCACertEntry 3 } docsBpi2CmtsCACertSerialNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This CA certificate's serial number, represented as an octet string." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.2.2" ::= { docsBpi2CmtsCACertEntry 4 } docsBpi2CmtsCACertTrust OBJECT-TYPE SYNTAX INTEGER { trusted (1), untrusted (2), chained (3), root (4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object controls the trust status of this certificate. Root certificates must be given root(4) trust; manufacturer certificates must not be given root(4) trust. Trust on root certificates must not change. Note: Setting this object need only affect the validity of CM certificates sent in future authorization requests; instantaneous effect need not occur." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.4.1" DEFVAL { chained } ::= { docsBpi2CmtsCACertEntry 5 } docsBpi2CmtsCACertSource OBJECT-TYPE SYNTAX INTEGER { snmp (1), configurationFile (2), externalDatabase (3), other (4), authentInfo (5), compiledIntoCode (6) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates how the certificate reached the CMTS. Other(4) means that it originated from a source not identified above." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.4.1" ::= { docsBpi2CmtsCACertEntry 6 } docsBpi2CmtsCACertStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. An attempt to set writable columnar values while this row is active behaves as follows: - Sets to the object docsBpi2CmtsCACertTrust are allowed. - Sets to the object docsBpi2CmtsCACert will return an error of 'inconsistentValue'. A newly created entry cannot be set to active until the value of docsBpi2CmtsCACert is being set." ::= { docsBpi2CmtsCACertEntry 7 } docsBpi2CmtsCACert OBJECT-TYPE SYNTAX DocsX509ASN1DEREncodedCertificate MAX-ACCESS read-create STATUS current DESCRIPTION "An X509 DER-encoded Certificate Authority certificate. To help identify certificates, either this object or docsBpi2CmtsCACertThumbprint must be returned by a CMTS for self-signed CA certificates. Note: The zero-length OCTET STRING must be returned, on reads, if the entire certificate is not retained in the CMTS." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.2." ::= { docsBpi2CmtsCACertEntry 8 } docsBpi2CmtsCACertThumbprint OBJECT-TYPE SYNTAX OCTET STRING (SIZE (20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SHA-1 hash of a CA certificate. To help identify certificates, either this object or docsBpi2CmtsCACert must be returned by a CMTS for self-signed CA certificates. Note: The zero-length OCTET STRING must be returned, on reads, if the CA certificate thumb print is not retained in the CMTS." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section 9.4.3" ::= { docsBpi2CmtsCACertEntry 9 } -- -- Authenticated Software Download Objects -- -- -- Note: the authenticated software download objects are a -- CM requirement only. -- docsBpi2CodeDownloadControl OBJECT IDENTIFIER ::= { docsBpi2MIBObjects 4 } docsBpi2CodeDownloadStatusCode OBJECT-TYPE SYNTAX INTEGER { configFileCvcVerified (1), configFileCvcRejected (2), snmpCvcVerified (3), snmpCvcRejected (4), codeFileVerified (5), codeFileRejected (6), other (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value indicates the result of the latest config file CVC verification, SNMP CVC verification, or code file verification." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Sections D.3.3.2 and D.3.5.1." ::= { docsBpi2CodeDownloadControl 1 } docsBpi2CodeDownloadStatusString OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the additional information to the status code. The value will include the error code and error description, which will be defined separately." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section D.3.7" ::= { docsBpi2CodeDownloadControl 2 } docsBpi2CodeMfgOrgName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the device manufacturer's organizationName." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section D.3.2.2." ::= { docsBpi2CodeDownloadControl 3 } docsBpi2CodeMfgCodeAccessStart OBJECT-TYPE SYNTAX DateAndTime (SIZE(11)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the device manufacturer's current codeAccessStart value. This value will always refer to Greenwich Mean Time (GMT), and the value format must contain TimeZone information (fields 8-10)." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section D.3.2.2." ::= { docsBpi2CodeDownloadControl 4 } docsBpi2CodeMfgCvcAccessStart OBJECT-TYPE SYNTAX DateAndTime (SIZE(11)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the device manufacturer's current cvcAccessStart value. This value will always refer to Greenwich Mean Time (GMT), and the value format must contain TimeZone information (fields 8-10)." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section D.3.2.2." ::= { docsBpi2CodeDownloadControl 5 } docsBpi2CodeCoSignerOrgName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the co-signer's organizationName. The value is a zero length string if the co-signer is not specified." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section D.3.2.2." ::= { docsBpi2CodeDownloadControl 6 } docsBpi2CodeCoSignerCodeAccessStart OBJECT-TYPE SYNTAX DateAndTime (SIZE(11)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the co-signer's current codeAccessStart value. This value will always refer to Greenwich Mean Time (GMT), and the value format must contain TimeZone information (fields 8-10). If docsBpi2CodeCoSignerOrgName is a zero length string, the value of this object is meaningless." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section D.3.2.2." ::= { docsBpi2CodeDownloadControl 7 } docsBpi2CodeCoSignerCvcAccessStart OBJECT-TYPE SYNTAX DateAndTime (SIZE(11)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the co-signer's current cvcAccessStart value. This value will always refer to Greenwich Mean Time (GMT), and the value format must contain TimeZone information (fields 8-10). If docsBpi2CodeCoSignerOrgName is a zero length string, the value of this object is meaningless." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section D.3.2.2." ::= { docsBpi2CodeDownloadControl 8 } docsBpi2CodeCvcUpdate OBJECT-TYPE SYNTAX DocsX509ASN1DEREncodedCertificate MAX-ACCESS read-write STATUS current DESCRIPTION "Setting a CVC to this object triggers the device to verify the CVC and update the cvcAccessStart values. The content of this object is then discarded. If the device is not enabled to upgrade codefiles, or if the CVC verification fails, the CVC will be rejected. Reading this object always returns the zero-length OCTET STRING." REFERENCE "DOCSIS Baseline Privacy Plus Interface Specification, Section D.3.3.2.2." ::= { docsBpi2CodeDownloadControl 9 } -- -- The BPI+ MIB Conformance Statements (with a placeholder for -- notifications) -- docsBpi2Notification OBJECT IDENTIFIER ::= { docsBpi2MIB 0 } docsBpi2Conformance OBJECT IDENTIFIER ::= { docsBpi2MIB 2 } docsBpi2Compliances OBJECT IDENTIFIER ::= { docsBpi2Conformance 1 } docsBpi2Groups OBJECT IDENTIFIER ::= { docsBpi2Conformance 2 } docsBpi2CmCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "This is the compliance statement for CMs that implement the DOCSIS Baseline Privacy Interface Plus." MODULE -- docsBpi2MIB -- unconditionally mandatory group MANDATORY-GROUPS { docsBpi2CmGroup, docsBpi2CodeDownloadGroup } -- constrain on Encryption algorithms OBJECT docsBpi2CmTEKDataEncryptAlg SYNTAX DocsBpkmDataEncryptAlg { none(0), des56CbcMode(1), des40CbcMode(2) } DESCRIPTION "It is compliant to support des56CbcMode(1) and des40CbcMode(2) for data encryption algorithms." -- constrain on Integrity algorithms OBJECT docsBpi2CmTEKDataAuthentAlg SYNTAX DocsBpkmDataAuthentAlg { none(0) } DESCRIPTION "It is compliant to not support data message authentication algorithms." -- constrain on IP addressing OBJECT docsBpi2CmIpMulticastAddressType SYNTAX InetAddressType { ipv4(1) } DESCRIPTION "An implementation is only required to support IPv4 addresses. Support for other address types may be defined in future versions of this MIB module." -- constrain on IP addressing OBJECT docsBpi2CmIpMulticastAddress SYNTAX InetAddress (SIZE(4)) DESCRIPTION "An implementation is only required to support IPv4 addresses Other address types support may be defined in future versions of this MIB module." -- constrain on Encryption algorithms OBJECT docsBpi2CmCryptoSuiteDataEncryptAlg SYNTAX DocsBpkmDataEncryptAlg { none(0), des56CbcMode(1), des40CbcMode(2) } DESCRIPTION "It is compliant to only support des56CbcMode(1) and des40CbcMode(2) for data encryption algorithms." -- constrain on Integrity algorithms OBJECT docsBpi2CmCryptoSuiteDataAuthentAlg SYNTAX DocsBpkmDataAuthentAlg { none(0) } DESCRIPTION "It is compliant to not support data message authentication algorithms." ::= { docsBpi2Compliances 1 } docsBpi2CmtsCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "This is the compliance statement for CMTSs that implement the DOCSIS Baseline Privacy Interface Plus." MODULE -- docsBpi2MIB -- unconditionally mandatory group MANDATORY-GROUPS { docsBpi2CmtsGroup } -- unconditionally optional group GROUP docsBpi2CodeDownloadGroup DESCRIPTION "This group is optional for CMTSes. The implementation decision of this group is left to the vendor" -- constrain on mandatory range OBJECT docsBpi2CmtsDefaultAuthLifetime SYNTAX Integer32 (86400..6048000) DESCRIPTION "The refined range corresponds to the minimum and maximum values in operational networks." -- constrain on mandatory range OBJECT docsBpi2CmtsDefaultTEKLifetime SYNTAX Integer32 (1800..604800) DESCRIPTION "The refined range corresponds to the minimum and maximum values in operational networks." -- constrain on mandatory range OBJECT docsBpi2CmtsAuthCmLifetime SYNTAX Integer32 (86400..6048000) DESCRIPTION "The refined range corresponds to the minimum and maximum values in operational networks." -- constrain on Encryption algorithms OBJECT docsBpi2CmtsTEKDataEncryptAlg SYNTAX DocsBpkmDataEncryptAlg { none(0), des56CbcMode(1), des40CbcMode(2) } DESCRIPTION "It is compliant to only support des56CbcMode(1) and des40CbcMode(2) for data encryption." -- constrain on Integrity algorithms OBJECT docsBpi2CmtsTEKDataAuthentAlg SYNTAX DocsBpkmDataAuthentAlg { none(0) } DESCRIPTION "It is compliant to not support data message authentication algorithms." -- constrain on mandatory range OBJECT docsBpi2CmtsTEKLifetime SYNTAX Integer32 (1800..604800) DESCRIPTION "The refined range corresponds to the minimum and maximum values in operational networks." -- constrain on access -- constrain on IP Addressing OBJECT docsBpi2CmtsIpMulticastAddressType SYNTAX InetAddressType { ipv4(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support IPv4 addresses. Support for other address types may be defined in future versions of this MIB module." OBJECT docsBpi2CmtsIpMulticastAddress SYNTAX InetAddress (SIZE(4)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support IPv4 addresses. Support for other address types may be defined in future versions of this MIB module." OBJECT docsBpi2CmtsIpMulticastMask SYNTAX InetAddress (SIZE(4)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support IPv4 addresses. Support for other address types may be defined in future versions of this MIB module." -- constrain on access OBJECT docsBpi2CmtsIpMulticastSAId MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT docsBpi2CmtsIpMulticastSAType MIN-ACCESS read-only DESCRIPTION "Write access is not required." -- constrain on access -- constrain on Encryption algorithms OBJECT docsBpi2CmtsIpMulticastDataEncryptAlg SYNTAX DocsBpkmDataEncryptAlg { none(0), des56CbcMode(1), des40CbcMode(2) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. It is compliant to only support des56CbcMode(1) and des40CbcMode(2) for data encryption" -- constrain on access -- constrain on Integrity algorithms OBJECT docsBpi2CmtsIpMulticastDataAuthentAlg SYNTAX DocsBpkmDataAuthentAlg { none(0) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. It is compliant to not support data message authentication algorithms." -- constrain on access OBJECT docsBpi2CmtsMulticastAuthControl MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { docsBpi2Compliances 2 } docsBpi2CmGroup OBJECT-GROUP OBJECTS { docsBpi2CmPrivacyEnable, docsBpi2CmPublicKey, docsBpi2CmAuthState, docsBpi2CmAuthKeySequenceNumber, docsBpi2CmAuthExpiresOld, docsBpi2CmAuthExpiresNew, docsBpi2CmAuthReset, docsBpi2CmAuthGraceTime, docsBpi2CmTEKGraceTime, docsBpi2CmAuthWaitTimeout, docsBpi2CmReauthWaitTimeout, docsBpi2CmOpWaitTimeout, docsBpi2CmRekeyWaitTimeout, docsBpi2CmAuthRejectWaitTimeout, docsBpi2CmSAMapWaitTimeout, docsBpi2CmSAMapMaxRetries, docsBpi2CmAuthentInfos, docsBpi2CmAuthRequests, docsBpi2CmAuthReplies, docsBpi2CmAuthRejects, docsBpi2CmAuthInvalids, docsBpi2CmAuthRejectErrorCode, docsBpi2CmAuthRejectErrorString, docsBpi2CmAuthInvalidErrorCode, docsBpi2CmAuthInvalidErrorString, docsBpi2CmTEKSAType, docsBpi2CmTEKDataEncryptAlg, docsBpi2CmTEKDataAuthentAlg, docsBpi2CmTEKState, docsBpi2CmTEKKeySequenceNumber, docsBpi2CmTEKExpiresOld, docsBpi2CmTEKExpiresNew, docsBpi2CmTEKKeyRequests, docsBpi2CmTEKKeyReplies, docsBpi2CmTEKKeyRejects, docsBpi2CmTEKInvalids, docsBpi2CmTEKAuthPends, docsBpi2CmTEKKeyRejectErrorCode, docsBpi2CmTEKKeyRejectErrorString, docsBpi2CmTEKInvalidErrorCode, docsBpi2CmTEKInvalidErrorString, docsBpi2CmIpMulticastAddressType, docsBpi2CmIpMulticastAddress, docsBpi2CmIpMulticastSAId, docsBpi2CmIpMulticastSAMapState, docsBpi2CmIpMulticastSAMapRequests, docsBpi2CmIpMulticastSAMapReplies, docsBpi2CmIpMulticastSAMapRejects, docsBpi2CmIpMulticastSAMapRejectErrorCode, docsBpi2CmIpMulticastSAMapRejectErrorString, docsBpi2CmDeviceCmCert, docsBpi2CmDeviceManufCert, docsBpi2CmCryptoSuiteDataEncryptAlg, docsBpi2CmCryptoSuiteDataAuthentAlg } STATUS current DESCRIPTION "This collection of objects provides CM BPI+ status and control." ::= { docsBpi2Groups 1 } docsBpi2CmtsGroup OBJECT-GROUP OBJECTS { docsBpi2CmtsDefaultAuthLifetime, docsBpi2CmtsDefaultTEKLifetime, docsBpi2CmtsDefaultSelfSignedManufCertTrust, docsBpi2CmtsCheckCertValidityPeriods, docsBpi2CmtsAuthentInfos, docsBpi2CmtsAuthRequests, docsBpi2CmtsAuthReplies, docsBpi2CmtsAuthRejects, docsBpi2CmtsAuthInvalids, docsBpi2CmtsSAMapRequests, docsBpi2CmtsSAMapReplies, docsBpi2CmtsSAMapRejects, docsBpi2CmtsAuthCmBpiVersion, docsBpi2CmtsAuthCmPublicKey, docsBpi2CmtsAuthCmKeySequenceNumber, docsBpi2CmtsAuthCmExpiresOld, docsBpi2CmtsAuthCmExpiresNew, docsBpi2CmtsAuthCmLifetime, docsBpi2CmtsAuthCmReset, docsBpi2CmtsAuthCmInfos, docsBpi2CmtsAuthCmRequests, docsBpi2CmtsAuthCmReplies, docsBpi2CmtsAuthCmRejects, docsBpi2CmtsAuthCmInvalids, docsBpi2CmtsAuthRejectErrorCode, docsBpi2CmtsAuthRejectErrorString, docsBpi2CmtsAuthInvalidErrorCode, docsBpi2CmtsAuthInvalidErrorString, docsBpi2CmtsAuthPrimarySAId, docsBpi2CmtsAuthBpkmCmCertValid, docsBpi2CmtsAuthBpkmCmCert, docsBpi2CmtsAuthCACertIndexPtr, docsBpi2CmtsTEKSAType, docsBpi2CmtsTEKDataEncryptAlg, docsBpi2CmtsTEKDataAuthentAlg, docsBpi2CmtsTEKLifetime, docsBpi2CmtsTEKKeySequenceNumber, docsBpi2CmtsTEKExpiresOld, docsBpi2CmtsTEKExpiresNew, docsBpi2CmtsTEKReset, docsBpi2CmtsKeyRequests, docsBpi2CmtsKeyReplies, docsBpi2CmtsKeyRejects, docsBpi2CmtsTEKInvalids, docsBpi2CmtsKeyRejectErrorCode, docsBpi2CmtsKeyRejectErrorString, docsBpi2CmtsTEKInvalidErrorCode, docsBpi2CmtsTEKInvalidErrorString, docsBpi2CmtsIpMulticastAddressType, docsBpi2CmtsIpMulticastAddress, docsBpi2CmtsIpMulticastMask, docsBpi2CmtsIpMulticastSAId, docsBpi2CmtsIpMulticastSAType, docsBpi2CmtsIpMulticastDataEncryptAlg, docsBpi2CmtsIpMulticastDataAuthentAlg, docsBpi2CmtsIpMulticastSAMapRequests, docsBpi2CmtsIpMulticastSAMapReplies, docsBpi2CmtsIpMulticastSAMapRejects, docsBpi2CmtsIpMulticastSAMapRejectErrorCode, docsBpi2CmtsIpMulticastSAMapRejectErrorString, docsBpi2CmtsIpMulticastMapControl, docsBpi2CmtsIpMulticastMapStorageType, docsBpi2CmtsMulticastAuthControl, docsBpi2CmtsProvisionedCmCertTrust, docsBpi2CmtsProvisionedCmCertSource, docsBpi2CmtsProvisionedCmCertStatus, docsBpi2CmtsProvisionedCmCert, docsBpi2CmtsCACertSubject, docsBpi2CmtsCACertIssuer, docsBpi2CmtsCACertSerialNumber, docsBpi2CmtsCACertTrust, docsBpi2CmtsCACertSource, docsBpi2CmtsCACertStatus, docsBpi2CmtsCACert, docsBpi2CmtsCACertThumbprint } STATUS current DESCRIPTION "This collection of objects provides CMTS BPI+ status and control." ::= { docsBpi2Groups 2 } docsBpi2CodeDownloadGroup OBJECT-GROUP OBJECTS { docsBpi2CodeDownloadStatusCode, docsBpi2CodeDownloadStatusString, docsBpi2CodeMfgOrgName, docsBpi2CodeMfgCodeAccessStart, docsBpi2CodeMfgCvcAccessStart, docsBpi2CodeCoSignerOrgName, docsBpi2CodeCoSignerCodeAccessStart, docsBpi2CodeCoSignerCvcAccessStart, docsBpi2CodeCvcUpdate } STATUS current DESCRIPTION "This collection of objects provides authenticated software download support." ::= { docsBpi2Groups 3 } END