DVB-RCS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, transmission FROM SNMPv2-SMI -- [RFC2578] TEXTUAL-CONVENTION, RowStatus FROM SNMPv2-TC -- [RFC2579] OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF -- [RFC2580] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411] InetAddressType, InetAddress, InetAddressPrefixLength, InetPortNumber FROM INET-ADDRESS-MIB -- [RFC4001] Uri FROM URI-TC-MIB -- [RFC5017] Dscp, DscpOrAny FROM DIFFSERV-DSCP-TC -- [RFC3289] ; dvbRcsMib MODULE-IDENTITY LAST-UPDATED "201002161200Z" ORGANIZATION "The SatLabs Group" CONTACT-INFO "The SatLabs Group Web: www.satlabs.org E-mail: [email protected]" DESCRIPTION "DVB-RCS MIB subtree. This MIB module applies to equipment that is a Return Channel Satellite Terminal (RCST), defined in the Digital Video Broadcasting Return Channel via Satellite system (DVB-RCS) standard (ETSI EN 301 790 Digital Video Broadcasting (DVB); Interaction Channel for Satellite Distribution Systems, European Telecommunications Standards Institute (ETSI)). It defines a set of MIB objects to characterize the behavior and performance of network-layer entities implementing DVB-RCS. This MIB module is intended to be used by DVB-RCS equipment following the SatLabs System Recommendations, defined by the SatLabs Group and available at www.satlabs.org. Note that, if not stated otherwise in the object DESCRIPTION clause, all writable objects are persistent. Copyright (C) The IETF Trust (2010). This version of this MIB module is part of RFC 5728; see the RFC itself for full legal notices." REVISION "200907201200Z" DESCRIPTION "Revision of this MIB module, following MIB doctor review and adjustments based on the MIB authoring guidelines from the IETF." ::= { transmission 239 } --============================================================== -- Textual Conventions --============================================================== DvbRcsSatLabsProfileMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This textual convention enumerates the declaration of the SatLabs-defined terminal profiles. The mapping to the profiles is to be understood as described here. (0) refers to the most significant bit. dvbs(0) -> DVBS profile (DVB-S support) dvbs2ccm(1) -> DVB-S2 CCM profile (CCM support) dvbs2acm(2) -> DVB-S2 ACM profile (CCM, VCM and ACM support)" REFERENCE "SatLabs System Recommendations, available at www.satlabs.org." SYNTAX BITS { dvbs(0), dvbs2ccm(1), dvbs2acm(2), spare1(3), spare2(4), spare3(5), spare4(6), spare5(7), spare6(8), spare7(9), spare8(10), spare9(11), spare10(12), spare11(13), spare12(14), spare13(15), spare14(16), spare15(17), spare16(18), spare17(19), spare18(20), spare19(21), spare20(22), spare21(23), spare22(24), spare23(25), spare24(26), spare25(27), spare26(28), spare27(29), spare28(30), spare29(31) } DvbRcsSatLabsOptionMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This textual convention enumerates the declaration of the SatLabs-defined options. A value of 1 indicates that the respective option is supported. The mapping to the options is to be understood as described here. (0) refers to the most significant bit. mpegTrf(0) -> MPEG_TRF coarseSync(1) -> COARSE_SYNC wideHop(2) -> WIDE_HOPP fastHop(3) -> FAST_HOPP dynamicMfTdma(4) -> Dynamic_MF_TDMA contentionSync(5) -> CONTENTION_SYNC qpskLow(6) -> QPSKLOW mod16Apsk(7) -> 16APSK mod32Apsk(8) -> 32APSK normalFec(9) -> NORMALFEC multiTs(10) -> MULTITS gsTs(11) -> GSTS enhQoS(12) -> ENHQOS pep(13) -> PEP http(14) -> HTTP ftp(15) -> FTP dns(16) -> DNS chIdStrict(17) -> CHID_STRICT nlid(18) -> NLID snmpMisc(19) -> SNMPMISC The support of specific options mandates the support of specific objects and access levels." REFERENCE "SatLabs System Recommendations, available at www.satlabs.org." SYNTAX BITS { mpegTrf(0), coarseSync(1), wideHop(2), fastHop(3), dynamicMfTdma(4), contentionSync(5), qpskLow(6), mod16Apsk(7), mod32Apsk(8), normalFec(9), multiTs(10), gsTs(11), enhQoS(12), pep(13), http(14), ftp(15), dns(16), chIdStrict(17), nlid(18), snmpMisc(19), spare1(20), spare2(21), spare3(22), spare4(23), spare5(24), spare6(25), spare7(26), spare8(27), spare9(28), spare10(29), spare11(30), spare12(31) } DvbRcsSatLabsFeatureMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This textual convention enumerates the declaration of the SatLabs-specified compatibility and configuration features. A value of 1 indicates that the respective feature is supported. The mapping to the features is to be understood as described here. (0) refers to the most significant bit. rcstPara(0) -> RCST_PARA feature installLog(1) -> INSTALL_LOG feature enhClassifier(2) -> ENHCLASSIFIER feature routeId(3) -> ROUTE_ID feature oduList(4) -> ODULIST feature extNetwork(5) -> EXTNETWORK feature extControl(6) -> EXTCONTROL feature extConfig(7) -> EXTCONFIG feature extStatus(8) -> EXTSTATUS feature mpaf(9) -> MPAF feature The support of specific features mandates the support of specific objects and access levels." REFERENCE "SatLabs System Recommendations, available at www.satlabs.org." SYNTAX BITS { rcstPara(0), installLog(1), enhClassifier(2), routeId(3), oduList(4), extNetwork(5), extControl(6), extConfig(7), extStatus(8), mpaf(9), spare1(10), spare2(11), spare3(12), spare4(13), spare5(14), spare6(15), spare7(16), spare8(17), spare9(18), spare10(19), spare11(20), spare12(21), spare13(22), spare14(23), spare15(24), spare16(25), spare17(26), spare18(27), spare19(28), spare20(29), spare21(30), spare22(31) } --============================================================== -- object type definitions --============================================================== dvbRcsMibObjects OBJECT IDENTIFIER ::= {dvbRcsMib 1} dvbRcsConformance OBJECT IDENTIFIER ::= {dvbRcsMib 2} dvbRcsRcst OBJECT IDENTIFIER ::= {dvbRcsMibObjects 1} dvbRcsFwdLink OBJECT IDENTIFIER ::= {dvbRcsMibObjects 2} dvbRcsRtnLink OBJECT IDENTIFIER ::= {dvbRcsMibObjects 3} dvbRcsRcstSystem OBJECT IDENTIFIER ::= {dvbRcsRcst 1} dvbRcsRcstNetwork OBJECT IDENTIFIER ::= {dvbRcsRcst 2} dvbRcsRcstInstall OBJECT IDENTIFIER ::= {dvbRcsRcst 3} dvbRcsRcstQos OBJECT IDENTIFIER ::= {dvbRcsRcst 4} dvbRcsRcstControl OBJECT IDENTIFIER ::= {dvbRcsRcst 5} dvbRcsRcstState OBJECT IDENTIFIER ::= {dvbRcsRcst 6} dvbRcsFwdConfig OBJECT IDENTIFIER ::= {dvbRcsFwdLink 1} dvbRcsFwdStatus OBJECT IDENTIFIER ::= {dvbRcsFwdLink 2} dvbRcsRtnConfig OBJECT IDENTIFIER ::= {dvbRcsRtnLink 1} dvbRcsRtnStatus OBJECT IDENTIFIER ::= {dvbRcsRtnLink 2} --============================================================== -- dvbRcsRcstSystem sub-tree object types --============================================================== dvbRcsSystemMibRevision OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object allows the SNMP agent to report the implemented MIB module revision. The supported REVISION of this module is reported." ::= {dvbRcsRcstSystem 1} --============================================================== -- Options declared according to the textual conventions --============================================================== dvbRcsSystemSatLabsProfilesDeclaration OBJECT-TYPE SYNTAX DvbRcsSatLabsProfileMap MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the SatLabs profiles supported, as defined in the SatLabs System Recommendations." ::= {dvbRcsRcstSystem 2} dvbRcsSystemSatLabsOptionsDeclaration OBJECT-TYPE SYNTAX DvbRcsSatLabsOptionMap MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the SatLabs options supported, as defined in the SatLabs System Recommendations." ::= {dvbRcsRcstSystem 3} dvbRcsSystemSatLabsFeaturesDeclaration OBJECT-TYPE SYNTAX DvbRcsSatLabsFeatureMap MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the optional compatibility features and minor options supported, as defined in the SatLabs System Recommendations." ::= {dvbRcsRcstSystem 4} dvbRcsSystemLocation OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "Physical location of the ODU antenna expressed as longitude, latitude, and altitude. The string shall have 31 characters in the following format: <xxxx.xxx>,<a>,<yyyyy.yyy>,<b>,<zzzz.z>,M where x, y and z represents digits, a=N or S, b=E or W, Reading the digits from left to right: 'x' 7 latitude digits; x digits 1-2 contain the degrees, x digits 3-7 contain the minutes in decimal; 'y' 8 longitude digits; y digits 1-3 contain the degrees, y digits 4-8 contain the minutes in decimal; 'z' 5 altitude digits; meters above sea level in decimal; '.' is the decimal point; ',' is the field separator; 'M' is the indicator for altitude meters. This format is a modified subset of the NMEA 0183 (National Marine Electronics Association, Interface Standard) format for Global Positioning System Fix Data. This location and the satellite position are used to calculate the RCST-satellite path delay. Note: The system.sysLocation object of MIB-II provides physical location of the IDU unit." ::= {dvbRcsRcstSystem 5} dvbRcsSystemOduAntennaSize OBJECT-TYPE SYNTAX Unsigned32 UNITS "cm" MAX-ACCESS read-write STATUS current DESCRIPTION "Diameter of the antenna." ::= {dvbRcsRcstSystem 6} dvbRcsSystemOduAntennaGain OBJECT-TYPE SYNTAX Unsigned32 UNITS "x0.1 dBi" MAX-ACCESS read-write STATUS current DESCRIPTION "Antenna peak gain of the ODU." ::= {dvbRcsRcstSystem 7} dvbRcsSystemOduSspa OBJECT-TYPE SYNTAX Unsigned32 UNITS "x0.1 W" MAX-ACCESS read-write STATUS current DESCRIPTION "Power level of the Solid State Power Amplifier installed in the ODU." ::= {dvbRcsRcstSystem 8} dvbRcsSystemOduTxType OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "Type of transmitter installed in the ODU." ::= {dvbRcsRcstSystem 9} dvbRcsSystemOduRxType OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "Type of LNB installed in the ODU, with information such as vendor type, output type (single, twin, quad,...), etc." ::= {dvbRcsRcstSystem 10} dvbRcsSystemOduRxBand OBJECT-TYPE SYNTAX INTEGER { oduHighRxBand (0), oduLowRxBand (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "LNB High Band / Low Band selector. High Band corresponds to the emission of an 18-26 kHz tone with 0.4-0.8 Vpp in the Rx IFL cable: (0) - High Band (1) - Low Band" ::= {dvbRcsRcstSystem 11} dvbRcsSystemOduRxLO OBJECT-TYPE SYNTAX Unsigned32 UNITS "x100 Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "Frequency of LNB Local Oscillator (in 100 Hz)" ::= {dvbRcsRcstSystem 12} dvbRcsSystemOduTxLO OBJECT-TYPE SYNTAX Unsigned32 UNITS "x100 Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "Frequency of Block Up-Converter Local Oscillator (in 100 Hz)." ::= {dvbRcsRcstSystem 13} dvbRcsSystemIduPep OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 14} dvbRcsTcpPep OBJECT-TYPE SYNTAX INTEGER{ disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Status and control of embedded TCP PEP. 0 - disabled or not implemented 1 - enabled" ::={dvbRcsSystemIduPep 1} dvbRcsHttpPep OBJECT-TYPE SYNTAX INTEGER{ disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Status and control of embedded HTTP PEP. 0 - disabled or not implemented 1 - enabled" ::={dvbRcsSystemIduPep 2} --============================================================== -- ODU structural entities --============================================================== dvbRcsOduTx OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 15} dvbRcsOduRx OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 16} dvbRcsOduAntenna OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 17} --============================================================== -- ODU BUC --============================================================== dvbRcsOduTxTypeTable OBJECT-TYPE SYNTAX SEQUENCE OF DvbRcsOduTxTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the identification of each well- known BUC type supported by the IDU and provides its associated index." ::={dvbRcsOduTx 1} dvbRcsOduTxTypeEntry OBJECT-TYPE SYNTAX DvbRcsOduTxTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the BUC type table." INDEX { dvbRcsOduTxTypeIndex } ::={dvbRcsOduTxTypeTable 1} DvbRcsOduTxTypeEntry ::= SEQUENCE { dvbRcsOduTxTypeIndex Unsigned32, dvbRcsOduTxTypeDescription SnmpAdminString } dvbRcsOduTxTypeIndex OBJECT-TYPE SYNTAX Unsigned32 (1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for the BUC type." ::={dvbRcsOduTxTypeEntry 1} dvbRcsOduTxTypeDescription OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Text-based identification of a BUC type." ::={dvbRcsOduTxTypeEntry 2} dvbRcsOduTxType OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Index of the selected BUC type." ::={dvbRcsOduTx 2} --============================================================== -- ODU LNB --============================================================== dvbRcsOduRxTypeTable OBJECT-TYPE SYNTAX SEQUENCE OF DvbRcsOduRxTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the identification of each well- known LNB type supported by the IDU and provides its associated index." ::={dvbRcsOduRx 1} dvbRcsOduRxTypeEntry OBJECT-TYPE SYNTAX DvbRcsOduRxTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the LNB type table." INDEX { dvbRcsOduRxTypeIndex } ::={dvbRcsOduRxTypeTable 1} DvbRcsOduRxTypeEntry ::= SEQUENCE { dvbRcsOduRxTypeIndex Unsigned32, dvbRcsOduRxTypeDescription SnmpAdminString } dvbRcsOduRxTypeIndex OBJECT-TYPE SYNTAX Unsigned32 (1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for the LNB type." ::={dvbRcsOduRxTypeEntry 1} dvbRcsOduRxTypeDescription OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Text-based identification of an LNB type." ::={dvbRcsOduRxTypeEntry 2} dvbRcsOduRxType OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Index of the selected LNB type." ::={dvbRcsOduRx 2} --============================================================== -- ODU Antenna --============================================================== dvbRcsOduAntennaTypeTable OBJECT-TYPE SYNTAX SEQUENCE OF DvbRcsOduAntennaTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the identification of each well- known antenna type supported by the IDU and provides its associated index." ::={dvbRcsOduAntenna 1} dvbRcsOduAntennaTypeEntry OBJECT-TYPE SYNTAX DvbRcsOduAntennaTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the antenna type table." INDEX { dvbRcsOduAntennaTypeIndex } ::={dvbRcsOduAntennaTypeTable 1} DvbRcsOduAntennaTypeEntry ::= SEQUENCE { dvbRcsOduAntennaTypeIndex Unsigned32, dvbRcsOduAntennaTypeDescription SnmpAdminString } dvbRcsOduAntennaTypeIndex OBJECT-TYPE SYNTAX Unsigned32 (1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for the antenna type." ::={dvbRcsOduAntennaTypeEntry 1} dvbRcsOduAntennaTypeDescription OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Text-based identification of an antenna type." ::={dvbRcsOduAntennaTypeEntry 2} dvbRcsOduAntennaType OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Index of the selected antenna type." ::={dvbRcsOduAntenna 2} --============================================================== -- dvbRcsRcstNetwork sub-tree object types --============================================================== dvbRcsNetworkOamInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Internet address of dvbRcsNetworkOamInetAddress. If the terminal OAM Internet address is unassigned or unknown, then the value of this object is unknown(0)." ::= {dvbRcsRcstNetwork 1} dvbRcsNetworkOamInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "OAM IP Address of the RCST. This object is used with both IP and interfaces MIB-II subgroups. It uniquely determines the interface through which OAM traffic passes. The OAM IP address may be statically or dynamically assigned. It is system dependent whether the OAM IP address and the Traffic IP address are the same address. If the terminal has no OAM Internet address assigned or if this Internet address is unknown, the value of this object is the zero-length OCTET STRING. The InetAddressType is given by the dvbRcsNetworkOamInetAddressType object." ::= {dvbRcsRcstNetwork 2} dvbRcsNetworkOamInetAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-write STATUS current DESCRIPTION "Prefix length for the OAM IP Address. If this address prefix is unknown or does not apply, the value is zero." ::= {dvbRcsRcstNetwork 3} dvbRcsNetworkOamInetAddressAssign OBJECT-TYPE SYNTAX INTEGER { oamInetAddressStatic (1), oamInetAddressDynamic (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Identifies whether the OAM IP address is statically (1) or dynamically (2) assigned." ::= {dvbRcsRcstNetwork 4} dvbRcsNetworkLanInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Internet address of dvbRcsNetworkLanInetAddress. If the terminal Internet address on the LAN interface is unassigned or unknown, then the value of this object is unknown(0)." ::= {dvbRcsRcstNetwork 5} dvbRcsNetworkLanInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address of the LAN interface of the terminal. If the terminal has no Internet address assigned on the LAN interface or if this Internet address is unknown, the value of this object is the zero-length OCTET STRING. The InetAddressType is given by the dvbRcsNetworkLanInetAddressType object." ::= {dvbRcsRcstNetwork 6} dvbRcsNetworkLanInetAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-write STATUS current DESCRIPTION "Prefix length for the LAN IP Address of the terminal. If this address prefix is unknown or does not apply, the value is zero." ::= {dvbRcsRcstNetwork 7} dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Internet address of dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress. If the default gateway Internet address is unassigned or unknown, then the value of this object is unknown(0)." ::= {dvbRcsRcstNetwork 8} dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address of the default gateway for the air interface. If the terminal has no default gateway assigned on the air interface or if this Internet address is unknown, the value of this object is the zero-length OCTET STRING. The InetAddressType is given by the dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType object." ::= {dvbRcsRcstNetwork 9} dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-write STATUS current DESCRIPTION "Prefix length for the IP address of the default gateway for the air interface. If this address prefix is unknown or does not apply, the value is zero." ::= {dvbRcsRcstNetwork 10} dvbRcsNetworkDnsServers OBJECT IDENTIFIER ::= {dvbRcsRcstNetwork 11} dvbRcsPrimaryDnsServerInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Internet address of dvbRcsPrimaryDnsServerInetAddress. If the primary DNS server Internet address is unassigned or unknown, then the value of this object is unknown(0)." ::= { dvbRcsNetworkDnsServers 1} dvbRcsPrimaryDnsServerInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address of the primary DNS server in the NCC. If the terminal has no primary DNS server assigned or if this Internet address is unknown, the value of this object is the zero-length OCTET STRING. The InetAddressType is given by the dvbRcsPrimaryDnsServerInetAddressType object." ::= {dvbRcsNetworkDnsServers 2} dvbRcsPrimaryDnsServerInetAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-write STATUS current DESCRIPTION "Prefix length for the IP address of the primary DNS server in the NCC. If this address prefix is unknown or does not apply, the value is zero." ::= { dvbRcsNetworkDnsServers 3} dvbRcsSecondaryDnsServerInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Internet address of dvbRcsSecondaryDnsServerInetAddress. If the secondary DNS server Internet address is unassigned or unknown, then the value of this object is unknown(0)." ::= { dvbRcsNetworkDnsServers 4} dvbRcsSecondaryDnsServerInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address of the secondary DNS server in the NCC. If the terminal has no secondary DNS server assigned or if this Internet address is unknown, the value of this object is the zero-length OCTET STRING. The InetAddressType is given by the dvbRcsSecondaryDnsServerInetAddressType object." ::= {dvbRcsNetworkDnsServers 5} dvbRcsSecondaryDnsServerInetAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-write STATUS current DESCRIPTION "Prefix length for the IP address of the secondary DNS server in the NCC. If this address prefix is unknown or does not apply, the value is zero." ::= { dvbRcsNetworkDnsServers 6} dvbRcsNetworkNccMgtInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Internet address of dvbRcsNetworkNccMgtInetAddress. If the management server Internet address is unassigned or unknown, then the value of this object is unknown(0)." ::= {dvbRcsRcstNetwork 12} dvbRcsNetworkNccMgtInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address of the management server in the NCC. If the terminal has no management server assigned or if this Internet address is unknown, the value of this object is the zero-length OCTET STRING. The InetAddressType is given by the dvbRcsNetworkNccMgtInetAddressType object." ::= {dvbRcsRcstNetwork 13} dvbRcsNetworkNccMgtInetAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-write STATUS current DESCRIPTION "Prefix length for the IP address of the management server in the NCC. If this address prefix is unknown or does not apply, the value is zero." ::= { dvbRcsRcstNetwork 14} dvbRcsNetworkConfigFileDownloadUrl OBJECT-TYPE SYNTAX Uri (SIZE(0..65535)) MAX-ACCESS read-write STATUS current DESCRIPTION "Full path name for the configuration file download. It includes the protocol type (TFTP or FTP) and the associated server IP address or hostname. Hostname can only be used if DNS is supported by the RCST. The format of this parameter follows RFC 3986." ::= {dvbRcsRcstNetwork 15} dvbRcsNetworkInstallLogFileDownloadUrl OBJECT-TYPE SYNTAX Uri (SIZE(0..65535)) MAX-ACCESS read-write STATUS current DESCRIPTION "Full path of the installation log file to download. It includes the protocol type (TFTP or FTP) and the associated server IP address or hostname. Hostname can only be used if DNS is supported by the RCST. The installation log file can be created on the installer's computer and downloaded to the RCST. The format of this parameter follows RFC 3986." ::= {dvbRcsRcstNetwork 16} dvbRcsNetworkConfigFileUploadUrl OBJECT-TYPE SYNTAX Uri(SIZE(0..65535)) MAX-ACCESS read-write STATUS current DESCRIPTION "Full path name for the configuration file upload. It includes the protocol type (TFTP or FTP) and the associated server IP address or hostname. Hostname can only be used if DNS is supported by the RCST. The format of this parameter follows RFC 3986." ::= {dvbRcsRcstNetwork 17} dvbRcsNetworkLogFileUploadUrl OBJECT-TYPE SYNTAX Uri(SIZE(0..65535)) MAX-ACCESS read-write STATUS current DESCRIPTION "Full path of the event log file. It includes the protocol type (TFTP or FTP) and the associated server IP address or hostname. Hostname can only be used if DNS is supported by the RCST. The format of this parameter follows RFC 3986." ::= {dvbRcsRcstNetwork 18} dvbRcsNetworkInstallLogFileUploadUrl OBJECT-TYPE SYNTAX Uri(SIZE(0..65535)) MAX-ACCESS read-write STATUS current DESCRIPTION "Full path of the installation log file. It includes the protocol type (TFTP or FTP) and the associated server IP address or hostname. Hostname can only be used if DNS is supported by the RCST. The installation log file can be retrieved from the RCST by the NCC or by the installer via the LAN. The format of this parameter follows RFC 3986." ::= {dvbRcsRcstNetwork 19} --============================================================== -- dvbRcsRcstInstall sub-tree object types --============================================================== dvbRcsInstallAntennaAlignmentState OBJECT-TYPE SYNTAX INTEGER { antennaAlignmentStart (1), antennaAlignmentDeny (2), antennaAlignmentContinue(3), antennaAlignmentStop (4), antennaAlignmentSuccess (5), antennaAlignmentFail (6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the alignment state of the antenna: (1)-Start; (2)-Deny; (3)-Continue; (4)-Stop; (5)-Success; (6)-Fail" ::= {dvbRcsRcstInstall 1} dvbRcsInstallCwFrequency OBJECT-TYPE SYNTAX Unsigned32 UNITS "x100 Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "Frequency of the transmitted Continuous Wave carrier (in 100 Hz). Minimum required precision is 1 kHz." ::= {dvbRcsRcstInstall 2} dvbRcsInstallCwMaxDuration OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time after which the Continuous Wave carrier must be put down (in seconds)." ::= {dvbRcsRcstInstall 3} dvbRcsInstallCwPower OBJECT-TYPE SYNTAX Integer32 UNITS "x0.1 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "IDU TX output level when the IDU is configured to send CW. The resolution is 0.1 dBm and the accuracy is +/- 1 dBm. Reconfiguration is applied immediately to a CW." ::= {dvbRcsRcstInstall 4} dvbRcsInstallCoPolReading OBJECT-TYPE SYNTAX Unsigned32 UNITS "x0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Co-polarization measured value during installation procedure (in 0.1 dB)." ::= {dvbRcsRcstInstall 5} dvbRcsInstallXPolReading OBJECT-TYPE SYNTAX Unsigned32 UNITS "x0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Cross-polarization measured value during installation procedure (in 0.1 dB)." ::= {dvbRcsRcstInstall 6} dvbRcsInstallCoPolTarget OBJECT-TYPE SYNTAX Unsigned32 UNITS "x0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Co-polarization target value during installation procedure (in 0.1 dB)." ::= {dvbRcsRcstInstall 7} dvbRcsInstallXPolTarget OBJECT-TYPE SYNTAX Unsigned32 UNITS "x0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Cross-polarization target value during installation procedure (in 0.1 dB)." ::= {dvbRcsRcstInstall 8} dvbRcsInstallStandByDuration OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time to wait in stand-by mode (in seconds)." ::= {dvbRcsRcstInstall 9} dvbRcsInstallTargetEsN0 OBJECT-TYPE SYNTAX Unsigned32(0..315) UNITS "x0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This value describes the wanted Es/N0 value that enables operation of the return link with the required error performance. The values shall be given in tenth of dB and the initial value shall be equal to 7 dB. The range shall be from 0 dB to 31.5 dB, with a precision of 0.1 dB." DEFVAL { 70 } ::= {dvbRcsRcstInstall 10} --============================================================== -- dvbRcsRcstQos sub-tree object types --============================================================== dvbRcsPktClassTable OBJECT-TYPE SYNTAX SEQUENCE OF DvbRcsPktClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the packet classification used in the DVB-RCS terminal. The number of entries is specified by dvbRcsPktClassIndex. " ::={dvbRcsRcstQos 1} dvbRcsPktClassEntry OBJECT-TYPE SYNTAX DvbRcsPktClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the packet classification table. One object type of each entry may have a value in the active range (a non-default value). The other object types are then assumed to be set to 'inactive'. The entry with the lowest index value takes precedence when classifying a packet." INDEX { dvbRcsPktClassIndex } ::= {dvbRcsPktClassTable 1} DvbRcsPktClassEntry ::= SEQUENCE { dvbRcsPktClassIndex Unsigned32, dvbRcsPktClassDscpLow Dscp, dvbRcsPktClassDscpHigh Dscp, dvbRcsPktClassDscpMarkValue DscpOrAny, dvbRcsPktClassIpProtocol Unsigned32, dvbRcsPktClassSrcInetAddressType InetAddressType, dvbRcsPktClassSrcInetAddress InetAddress, dvbRcsPktClassSrcInetAddressPrefixLength InetAddressPrefixLength, dvbRcsPktClassDstInetAddressType InetAddressType, dvbRcsPktClassDstInetAddress InetAddress, dvbRcsPktClassDstInetAddressPrefixLength InetAddressPrefixLength, dvbRcsPktClassSrcPortLow InetPortNumber, dvbRcsPktClassSrcPortHigh InetPortNumber, dvbRcsPktClassDstPortLow InetPortNumber, dvbRcsPktClassDstPortHigh InetPortNumber, dvbRcsPktClassVlanUserPri Integer32, dvbRcsPktClassPhbAssociation Unsigned32, dvbRcsPktClassRowStatus RowStatus } dvbRcsPktClassIndex OBJECT-TYPE SYNTAX Unsigned32 (1..64) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index automatically incremented by one at row creation." ::={dvbRcsPktClassEntry 1} dvbRcsPktClassDscpLow OBJECT-TYPE SYNTAX Dscp MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the low value of a range of Diffserv Code Point (DSCP) values to which a packet is compared." DEFVAL { 0 } ::={dvbRcsPktClassEntry 2} dvbRcsPktClassDscpHigh OBJECT-TYPE SYNTAX Dscp MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the high value of a range of Diffserv Code Point (DSCP) values to which a packet is compared." DEFVAL { 63 } ::={dvbRcsPktClassEntry 3} dvbRcsPktClassDscpMarkValue OBJECT-TYPE SYNTAX DscpOrAny MAX-ACCESS read-create STATUS current DESCRIPTION "This object is the Diffserv Code Point (DSCP) value used to mark the packet; -1 indicates no DSCP marking. Possible DSCP marks values are (0..63)" DEFVAL { -1 } ::={dvbRcsPktClassEntry 4} dvbRcsPktClassIpProtocol OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the IP protocol to which a packet is compared. A value of 255 means match all." DEFVAL { 255 } ::={dvbRcsPktClassEntry 5} dvbRcsPktClassSrcInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of Internet address of dvbRcsPktClassSrcInetAddress. If the packet class source Internet address is unassigned or unknown, then the value of this object is unknown(0)." ::= { dvbRcsPktClassEntry 6} dvbRcsPktClassSrcInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the IP source address to which a packet is compared. If the packet class has no source Internet address assigned or if this Internet address is unknown, the value of this object is the zero-length OCTET STRING. The InetAddressType is given by the dvbRcsPktClassSrcInetAddressType object." ::={dvbRcsPktClassEntry 7} dvbRcsPktClassSrcInetAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-create STATUS current DESCRIPTION "Prefix length of the IP source address that will be matched for this packet class. A value of zero indicates that the selectivity is inactive." DEFVAL { 0 } ::={dvbRcsPktClassEntry 8} dvbRcsPktClassDstInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of Internet address of dvbRcsPktClassDstInetAddress. If the packet class destination Internet address is unassigned or unknown, then the value of this object is unknown(0)." ::= { dvbRcsPktClassEntry 9} dvbRcsPktClassDstInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the IP destination address to which a packet is compared. If the packet class has no destination Internet address assigned or if this Internet address is unknown, the value of this object is the zero-length OCTET STRING. The InetAddressType is given by the dvbRcsPktClassDstInetAddressType object." ::={dvbRcsPktClassEntry 10} dvbRcsPktClassDstInetAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-create STATUS current DESCRIPTION "Prefix length of the IP source address that will be matched for this packet class. A value of zero indicates that the selectivity is inactive." DEFVAL { 0 } ::={dvbRcsPktClassEntry 11} dvbRcsPktClassSrcPortLow OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the low range of the source port to which a packet is compared. A value of 0 indicates that the selectivity is inactive." DEFVAL { 0 } ::={dvbRcsPktClassEntry 12} dvbRcsPktClassSrcPortHigh OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the high range of the source port to which a packet is compared. A value of 0 indicates that the selectivity is inactive." DEFVAL { 65535 } ::={dvbRcsPktClassEntry 13} dvbRcsPktClassDstPortLow OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the low range of the destination port to which a packet is compared. A value of 0 indicates that the selectivity is inactive." DEFVAL { 0 } ::={dvbRcsPktClassEntry 14} dvbRcsPktClassDstPortHigh OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the high range of the destination port to which a packet is compared. A value of 0 indicates that the selectivity is inactive." DEFVAL { 65535 } ::={dvbRcsPktClassEntry 15} dvbRcsPktClassVlanUserPri OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the VLAN User Priority to which a packet is compared. A value of -1 indicates that the selectivity is inactive." DEFVAL { -1 } ::={dvbRcsPktClassEntry 16} dvbRcsPktClassPhbAssociation OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Associate the filter entry to a specific PHB (refer to dvbRcsPhbIdentifier)." ::={dvbRcsPktClassEntry 17} dvbRcsPktClassRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time." ::={dvbRcsPktClassEntry 18} --============================================================== -- dvbRcsPhbMappingTable --============================================================== dvbRcsPhbMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF DvbRcsPhbMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is a list of Per-Hop Behavior (PHB) MIB entries. It describes the PHB mapping to the Request Class." ::={dvbRcsRcstQos 2} dvbRcsPhbMappingEntry OBJECT-TYPE SYNTAX DvbRcsPhbMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the PHB mapping table." INDEX {dvbRcsPhbIdentifier} ::= {dvbRcsPhbMappingTable 1} DvbRcsPhbMappingEntry ::= SEQUENCE { dvbRcsPhbIdentifier Unsigned32, dvbRcsPhbName SnmpAdminString, dvbRcsPhbRequestClassAssociation Unsigned32, dvbRcsPhbMappingRowStatus RowStatus } dvbRcsPhbIdentifier OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identification of the Per-Hop Behavior (PHB). It follows the unsigned 16-bit binary encoding as specified in RFC 3140. The value 0 designates the Default PHB." ::={dvbRcsPhbMappingEntry 1} dvbRcsPhbName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The name of the Per-Hop Behavior (PHB)." ::={dvbRcsPhbMappingEntry 2} dvbRcsPhbRequestClassAssociation OBJECT-TYPE SYNTAX Unsigned32 (1..16) MAX-ACCESS read-create STATUS current DESCRIPTION "This object is an association of this Per-Hop Behavior (PHB) to a Request Class (by reference to a Request Class index)." ::={dvbRcsPhbMappingEntry 3} dvbRcsPhbMappingRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time." DEFVAL { active } ::={dvbRcsPhbMappingEntry 4} --============================================================== -- dvbRcsRequestClassTable --============================================================== dvbRcsRequestClassTable OBJECT-TYPE SYNTAX SEQUENCE OF DvbRcsRequestClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is a list of Request Class entries. This class describes the layer 2 QoS objects." ::={dvbRcsRcstQos 3} dvbRcsRequestClassEntry OBJECT-TYPE SYNTAX DvbRcsRequestClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the Request Class table." INDEX {dvbRcsRequestClassIndex} ::= {dvbRcsRequestClassTable 1} DvbRcsRequestClassEntry ::= SEQUENCE { dvbRcsRequestClassIndex Unsigned32, dvbRcsRequestClassName SnmpAdminString, dvbRcsRequestClassChanId Unsigned32, dvbRcsRequestClassVccVpi Unsigned32, dvbRcsRequestClassVccVci Unsigned32, dvbRcsRequestClassPidPoolReference Unsigned32, dvbRcsRequestClassCra Unsigned32, dvbRcsRequestClassRbdcMax Unsigned32, dvbRcsRequestClassRbdcTimeout Unsigned32, dvbRcsRequestClassVbdcMax Unsigned32, dvbRcsRequestClassVbdcTimeout Unsigned32, dvbRcsRequestClassVbdcMaxBackLog Unsigned32, dvbRcsRequestClassRowStatus RowStatus } dvbRcsRequestClassIndex OBJECT-TYPE SYNTAX Unsigned32 (1..16) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the Request Class table. A total of 16 entries are supported." ::={dvbRcsRequestClassEntry 1} dvbRcsRequestClassName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "Name of the Request Class." ::={dvbRcsRequestClassEntry 2} dvbRcsRequestClassChanId OBJECT-TYPE SYNTAX Unsigned32 (0..15) MAX-ACCESS read-create STATUS current DESCRIPTION "Channel ID of the Request Class." ::={dvbRcsRequestClassEntry 3} dvbRcsRequestClassVccVpi OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Defines the VPI used for the Request Class (ATM profile)." ::={dvbRcsRequestClassEntry 4} dvbRcsRequestClassVccVci OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Defines the VCI used for the Request Class (ATM profile)." ::={dvbRcsRequestClassEntry 5} dvbRcsRequestClassPidPoolReference OBJECT-TYPE SYNTAX Unsigned32 (1..16) MAX-ACCESS read-create STATUS current DESCRIPTION "Reference to the Packet IDentifier (PID) pool applicable for the Request Class." ::={dvbRcsRequestClassEntry 6} dvbRcsRequestClassCra OBJECT-TYPE SYNTAX Unsigned32 UNITS "bit/s" MAX-ACCESS read-create STATUS current DESCRIPTION "Defines the Continuous Rate Assignment (CRA) level for the Request Class in bits per second (bit/s)." ::={dvbRcsRequestClassEntry 7} dvbRcsRequestClassRbdcMax OBJECT-TYPE SYNTAX Unsigned32 UNITS "x2 kbit/s" MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum Rate-Based Dynamic Capacity (RBDC) that can be requested for the Request Class, in number of 2 kbit/s." ::={dvbRcsRequestClassEntry 8} dvbRcsRequestClassRbdcTimeout OBJECT-TYPE SYNTAX Unsigned32 UNITS "superframes" MAX-ACCESS read-create STATUS current DESCRIPTION "Persistence of the Rate-Based Dynamic Capacity (RBDC) request, expressed in superframes." ::={dvbRcsRequestClassEntry 9} dvbRcsRequestClassVbdcMax OBJECT-TYPE SYNTAX Unsigned32 UNITS "ATM cells/MPEG packets" MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum Volume-Based Dynamic Capacity (VBDC) that can be allocated to the Request Class, in payload units (one ATM cell or one MPEG packet) per superframe." ::={dvbRcsRequestClassEntry 10} dvbRcsRequestClassVbdcTimeout OBJECT-TYPE SYNTAX Unsigned32 UNITS "superframes" MAX-ACCESS read-create STATUS current DESCRIPTION "Time after which the RCST considers that the pending requests are lost. The RCST may issue new requests for that traffic. Volume-Based Dynamic Capacity (VBDC) Timeout is expressed in superframes." ::={dvbRcsRequestClassEntry 11} dvbRcsRequestClassVbdcMaxBackLog OBJECT-TYPE SYNTAX Unsigned32 UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "Volume-Based Dynamic Capacity (VBDC) back log per Request Class (expressed in bytes)." ::={dvbRcsRequestClassEntry 12} dvbRcsRequestClassRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. It is not possible to change values in a row of this table while the row is active." ::={dvbRcsRequestClassEntry 13} --============================================================== -- The table of PID pools --============================================================== dvbRcsPidPoolTable OBJECT-TYPE SYNTAX SEQUENCE OF DvbRcsPidPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the Packet IDentifier (PID) pools. For the MPEG profile, several Request Classes may be mapped within a pool of several PIDs to allow Section Packing across several Request Classes. A PID value may occur in more than one PID pool. Each PID value can effectively occur only once in each pool." ::={dvbRcsRcstQos 4} dvbRcsPidPoolEntry OBJECT-TYPE SYNTAX DvbRcsPidPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the PID pool table." INDEX { dvbRcsPidPoolIndex, dvbRcsPidIndex } ::= {dvbRcsPidPoolTable 1} DvbRcsPidPoolEntry ::= SEQUENCE { dvbRcsPidPoolIndex Unsigned32, dvbRcsPidIndex Unsigned32, dvbRcsPidValue Unsigned32, dvbRcsPidPoolRowStatus RowStatus } dvbRcsPidPoolIndex OBJECT-TYPE SYNTAX Unsigned32 (1..16) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the PID pool in the PID pool table." ::={dvbRcsPidPoolEntry 1} dvbRcsPidIndex OBJECT-TYPE SYNTAX Unsigned32 (1..16) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the PID entry within the PID pool." ::={dvbRcsPidPoolEntry 2} dvbRcsPidValue OBJECT-TYPE SYNTAX Unsigned32 (0..8191) MAX-ACCESS read-create STATUS current DESCRIPTION "Defines one of the PIDs to be used in a PID pool of dvbRcsPidPoolIndex. A PID value may occur in more than one PID pool. Each PID value can effectively occur only once in each pool." ::={dvbRcsPidPoolEntry 3} dvbRcsPidPoolRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time." DEFVAL { active } ::={dvbRcsPidPoolEntry 4} dvbRcsQosGlobalRbdcMax OBJECT-TYPE SYNTAX Unsigned32 UNITS "x2 kbit/s" MAX-ACCESS read-write STATUS current DESCRIPTION "Global maximum RBDC that can be requested for the RCST, in number of 2 kbit/s." ::={dvbRcsRcstQos 5} dvbRcsQosGlobalVbdcMax OBJECT-TYPE SYNTAX Unsigned32 UNITS "ATM cells/MPEG packets" MAX-ACCESS read-write STATUS current DESCRIPTION "Global maximum VBDC that can be allocated to the RCST, in payload units (one ATM cell or one MPEG packet) per superframe." ::={dvbRcsRcstQos 6} dvbRcsQosGlobalVbdcMaxBackLog OBJECT-TYPE SYNTAX Unsigned32 UNITS "bytes" MAX-ACCESS read-write STATUS current DESCRIPTION "Global VBDC back log at the RCST level (expressed in bytes). It is used only if the VBDC back log is not configured in the Request Class (expressed in bytes)." ::={dvbRcsRcstQos 7} dvbRcsQosChannelIdStrictDispatching OBJECT-TYPE SYNTAX INTEGER { notStrict (0), strict (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether the RCST will strictly follow RC association when signaled through Channel_ID in the TBTP: (0)- no strict association (1)- strict association" ::={dvbRcsRcstQos 8} --============================================================== -- dvbRcsRcstControl sub-tree object types --============================================================== dvbRcsCtrlRebootCommand OBJECT-TYPE SYNTAX INTEGER { idle (1), normal (2), alternate (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable shall force the RCST to reboot: (1)- idle (2)- normal reboot (from current software load) (3)- reboot from alternate load (swap to alternate load before reboot)" DEFVAL {idle} ::={dvbRcsRcstControl 1} dvbRcsCtrlRcstTxDisable OBJECT-TYPE SYNTAX INTEGER { idle (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable shall force the RCST to stop transmission (transmit disabled as defined in SatLabs System Recommendations): (1)- idle (2)- initiate Tx Disabled" DEFVAL {idle} ::={dvbRcsRcstControl 2} dvbRcsCtrlUserTrafficDisable OBJECT-TYPE SYNTAX INTEGER { idle (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable shall disable user traffic (only RCST management traffic can be transmitted): (1)- idle (2)- disable user traffic" DEFVAL {idle} ::={dvbRcsRcstControl 3} dvbRcsCtrlCwEnable OBJECT-TYPE SYNTAX INTEGER { off (1), on (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable will force the RCST to start transmission of CW, if the RCST is first set to the installation state and is properly configured for CW transmission: (1)- off (2)- on" DEFVAL {off} ::={dvbRcsRcstControl 4} dvbRcsCtrlOduTxReferenceEnable OBJECT-TYPE SYNTAX INTEGER { off (1), on (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables activation and deactivation of the 10 MHz reference clock in the Tx IFL cable: (1) off (2) on" DEFVAL {on} ::={dvbRcsRcstControl 5} dvbRcsCtrlOduTxDCEnable OBJECT-TYPE SYNTAX INTEGER { off (1), on (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables activation and deactivation of DC in the Tx IFL cable: (1) off (2) on" DEFVAL {on} ::={dvbRcsRcstControl 6} dvbRcsCtrlOduRxDCEnable OBJECT-TYPE SYNTAX INTEGER { off (1), on (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables activation and deactivation of DC in the Rx IFL cable: (1) off (2) on" DEFVAL {on} ::={dvbRcsRcstControl 7} dvbRcsCtrlDownloadFileCommand OBJECT-TYPE SYNTAX INTEGER { idle (1), config (2), installationLog (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable will initiate an RCST configuration file download process: (1) idle (2) download RCST configuration file from TFTP/FTP server (3) download RCST installation log file from TFTP/FTP server (INSTALL_LOG feature)" DEFVAL {idle} ::={dvbRcsRcstControl 8} dvbRcsCtrlUploadFileCommand OBJECT-TYPE SYNTAX INTEGER { idle (1), config (2), eventAlarm (3), installationLog (4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable will initiate an RCST upload process: (1) idle (2) upload RCST configuration file to TFTP/FTP server (3) upload RCST event/alarm log file to TFTP/FTP server (4) upload RCST installation log file to TFTP/FTP server (INSTALL_LOG feature)" DEFVAL {idle} ::={dvbRcsRcstControl 9} dvbRcsCtrlActivateConfigFileCommand OBJECT-TYPE SYNTAX INTEGER { idle (1), activate (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Triggers the RCST to use the configuration file and update its parameters accordingly. Some RCST implementations may require a reboot for the parameters to take effect (vendor specific). (1) idle (2) activate" DEFVAL {idle} ::={dvbRcsRcstControl 10} dvbRcsCtrlRcstLogonCommand OBJECT-TYPE SYNTAX INTEGER { idle (1), logon (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable will initiate an RCST logon: (1) idle (2) initiate RCST logon" DEFVAL {idle} ::={dvbRcsRcstControl 11} dvbRcsCtrlRcstLogoffCommand OBJECT-TYPE SYNTAX INTEGER { idle (1), logoff (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable will initiate an RCST logoff: (1) idle (2) initiate RCST logoff" DEFVAL {idle} ::={dvbRcsRcstControl 12} dvbRcsCtrlRcstRxReacquire OBJECT-TYPE SYNTAX INTEGER { idle (1), reacquireForwardLink (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable will force the RCST to acquire the forward link and start receiving: (1) idle (2) reacquire forward link" DEFVAL {idle} ::={dvbRcsRcstControl 13} --============================================================== -- dvbRcsRcstState sub-tree object types --============================================================== dvbRcsRcstMode OBJECT-TYPE SYNTAX INTEGER { installation (0), operational (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Identifies the current mode of the RCST and allows the RCST to return to the installation mode when needed. Values for the RCST mode are: Installation (0) Operational (1)" ::={dvbRcsRcstState 1} dvbRcsRcstFaultStatus OBJECT-TYPE SYNTAX INTEGER { nofault (0), fault (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Provides the fault status of the terminal. The fault status management is vendor specific. Values for the fault status are: no fault (0) fault (1)" ::={dvbRcsRcstState 2} dvbRcsRcstFwdLinkStatus OBJECT-TYPE SYNTAX INTEGER { notAcquired (0), acquired (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Provides the status of the RCST forward link. Values for the forward link status are: Not acquired (0) Acquired (1)" ::={dvbRcsRcstState 3} dvbRcsRcstRtnLinkStatus OBJECT-TYPE SYNTAX INTEGER { loggedOff (0), loggedOn (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Provides the status of the RCST return link. Values for the return link status are: Logged-off (0) Logged-on (1)" ::={dvbRcsRcstState 4} dvbRcsRcstLogUpdated OBJECT-TYPE SYNTAX INTEGER { noUpdate (0), logfileUpdated (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the existence of an updated event log file: No update (0) Event Log file updated (1) The RCST should remove the 'Event Log file updated' indication as the log file is fetched by the NCC." ::={dvbRcsRcstState 5} dvbRcsRcstCurrentSoftwareVersion OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Current RCST software version." ::={dvbRcsRcstState 6} dvbRcsRcstAlternateSoftwareVersion OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Alternate (backup/new) RCST software version." ::={dvbRcsRcstState 7} dvbRcsRcstActivatedConfigFileVersion OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Version of the most recently activated configuration file. The version is vendor specific." ::={dvbRcsRcstState 8} dvbRcsRcstDownloadedConfigFileVersion OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Version of the most recently downloaded configuration file. Version is vendor specific. If the value is different from dvbRcsRcstActivatedConfigFileVersion, it is pending for activation." ::={dvbRcsRcstState 9} --============================================================== -- dvbRcsFwdConfig sub-tree object types --============================================================== dvbRcsFwdStartTable OBJECT-TYPE SYNTAX SEQUENCE OF DvbRcsFwdStartEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Lists forward link attachment points (e.g., different for installation and operation). The table describes the forward link parameters used for the start-up stream with the NCC." ::={dvbRcsFwdConfig 1} dvbRcsFwdStartEntry OBJECT-TYPE SYNTAX DvbRcsFwdStartEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the Forward Link Start Configuration table." INDEX {dvbRcsFwdStartIndex} ::= {dvbRcsFwdStartTable 1} DvbRcsFwdStartEntry ::= SEQUENCE { dvbRcsFwdStartIndex Unsigned32, dvbRcsFwdStartPopId Integer32, dvbRcsFwdStartFrequency Unsigned32, dvbRcsFwdStartPolar INTEGER, dvbRcsFwdStartFormat INTEGER, dvbRcsFwdStartRolloff INTEGER, dvbRcsFwdStartSymbolRate Unsigned32, dvbRcsFwdStartInnerFec INTEGER, dvbRcsFwdStartRowStatus RowStatus } dvbRcsFwdStartIndex OBJECT-TYPE SYNTAX Unsigned32 (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the Forward Link StartConfig table." ::={dvbRcsFwdStartEntry 1} dvbRcsFwdStartPopId OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Population identifier associated with the start-up forward link: -1: any (auto) 0-65535: specific StartPopId If 'any' is set, the RCST will assume membership of any announced population ID and will commence with logon in accordance with this assumption." ::={dvbRcsFwdStartEntry 2} dvbRcsFwdStartFrequency OBJECT-TYPE SYNTAX Unsigned32 UNITS "x100 kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Frequency of the start transponder carrying a Network Information Table to which any RCST shall trigger to acquire forward link. Its value shall be given in multiples of 100 kHz." ::={dvbRcsFwdStartEntry 3} dvbRcsFwdStartPolar OBJECT-TYPE SYNTAX INTEGER { linearHorizontal (0), linearVertical (1), circularLeft (2), circularRight (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "2-bit field giving the polarization of the start transponder carrying a Network Information Table to which any RCST shall trigger to acquire forward link: 00: linear and horizontal 01: linear and vertical 10: circular left 11: circular right" ::={dvbRcsFwdStartEntry 4} dvbRcsFwdStartFormat OBJECT-TYPE SYNTAX INTEGER { auto (-1), dvbs (0), dvbs2ccm (1), dvbs2acm (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the transmission format standard applied for the startup stream. The start transport stream carries a Network Information Table that the RCST uses for acquiring the forward link signaling. Supported values are: -1: unspecified (automatic format acquisition is assumed) 0: DVB-S (support of this value is mandatory if DVB-S support is claimed) 1: DVB-S2 with CCM (support of this value is mandatory if DVB-S2 CCM support is claimed) 2: DVB-S2 with VCM or ACM (support of this value is mandatory if DVB-S2 ACM support is claimed) This allows the RCST to discriminate between CCM and VCM/ACM when selecting the forward link. The support of automatic format selection is optional. One or several of the other format selections must be supported, according to the claimed SatLabs profile support." ::={dvbRcsFwdStartEntry 5} dvbRcsFwdStartRolloff OBJECT-TYPE SYNTAX INTEGER { autoRolloff (0), rolloff020 (1), rolloff025 (2), rolloff035 (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the receive filter roll-off applied on the start transponder. The start transponder carries a Network Information Table that the RCST uses for acquiring the forward link signaling. Supported values are: 0: any (auto) 1: 0.20 2: 0.25 3: 0.35" ::={dvbRcsFwdStartEntry 6} dvbRcsFwdStartSymbolRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "x100 symbols/s" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the symbol rate on the start transponder carrying a Network Information Table to which any RCST shall trigger to acquire forward link. Its value shall be given in multiples of 100 symbols/s." ::={dvbRcsFwdStartEntry 7} dvbRcsFwdStartInnerFec OBJECT-TYPE SYNTAX INTEGER { autoFec (-1), fecRate12 (0), fecRate23 (1), fecRate34 (2), fecRate56 (3), fecRate78 (4), fecRate89 (5), fecRate35 (6), fecRate45 (7), fecRate910 (8), fecRate25 (9), fecRate13 (10), fecRate14 (11), noInnerCode (12) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the inner Forward Error Correction used on the start transponder carrying a Network Information Table to which any RCST shall trigger to acquire forward link. Supported values are: autoFec (-1), fecRate1/2 (0), fecRate2/3 (1), fecRate3/4 (2), fecRate5/6 (3), fecRate7/8 (4), fecRate8/9 (5), fecRate3/5 (6), fecRate4/5 (7), fecRate9/10 (8), fecRate2/5 (9), fecRate1/3 (10), fecRate1/4 (11), noInnerCode (12) The support of autoFec is optional." ::={dvbRcsFwdStartEntry 8} dvbRcsFwdStartRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. It is not possible to change values in a row of this table while the row is active." ::={dvbRcsFwdStartEntry 9} --============================================================== -- dvbRcsFwdStatus sub-tree object types --============================================================== dvbRcsFwdStatusPopId OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Population identifier applied at log-on: 0-65535: specific StartPopId If the RCST was allowed to logon with any population, the RCST will report the base number of the announced population ID indicated by the RCS Map Table linkage descriptor used at logon." ::={dvbRcsFwdStatus 1} dvbRcsFwdStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF DvbRcsFwdStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the current status of Forward Link interfaces." ::={dvbRcsFwdStatus 2} dvbRcsFwdStatusEntry OBJECT-TYPE SYNTAX DvbRcsFwdStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the forward link status table. Each entry is associated with a physical interface. An RCST shall support at least one entry." INDEX { dvbRcsFwdStatusIndex } ::= {dvbRcsFwdStatusTable 1} DvbRcsFwdStatusEntry ::= SEQUENCE { dvbRcsFwdStatusIndex Unsigned32, dvbRcsFwdStatusIfReference Unsigned32, dvbRcsFwdStatusNetId Unsigned32, dvbRcsFwdStatusNetName SnmpAdminString, dvbRcsFwdStatusFormat INTEGER, dvbRcsFwdStatusFrequency Unsigned32, dvbRcsFwdStatusPolar INTEGER, dvbRcsFwdStatusInnerFec INTEGER, dvbRcsFwdStatusSymbolRate Unsigned32, dvbRcsFwdStatusRolloff INTEGER, dvbRcsFwdStatusModulation INTEGER, dvbRcsFwdStatusFecFrame INTEGER, dvbRcsFwdStatusPilot INTEGER, dvbRcsFwdStatusBer Integer32, dvbRcsFwdStatusCnr Integer32, dvbRcsFwdStatusRxPower Integer32 } dvbRcsFwdStatusIndex OBJECT-TYPE SYNTAX Unsigned32 (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the forward link status table." ::={dvbRcsFwdStatusEntry 1} dvbRcsFwdStatusIfReference OBJECT-TYPE SYNTAX Unsigned32 (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION "Cross reference to the interface table." ::={dvbRcsFwdStatusEntry 2} dvbRcsFwdStatusNetId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Interactive network identifier of the forward link (from the RCS Map Table)." ::={dvbRcsFwdStatusEntry 3} dvbRcsFwdStatusNetName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the interactive network of the forward link (from the RCS Map Table)." ::={dvbRcsFwdStatusEntry 4} dvbRcsFwdStatusFormat OBJECT-TYPE SYNTAX INTEGER { dvbs (0), dvbs2ccm (1), dvbs2acm (2), reservedFormat (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the transmission format applied on the forward link. Supported values are (from RCS Map Table): 0: DVB-S 1: DVB-S2 using CCM 2: DVB-S2 using VCM or ACM 3: reserved" ::={dvbRcsFwdStatusEntry 5} dvbRcsFwdStatusFrequency OBJECT-TYPE SYNTAX Unsigned32 UNITS "x100 kHz" MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the frequency of the forward link. Its value shall be given in multiples of 100 kHz." ::={dvbRcsFwdStatusEntry 6} dvbRcsFwdStatusPolar OBJECT-TYPE SYNTAX INTEGER { linearHorizontal (0), linearVertical (1), circularLeft (2), circularRight (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "2-bit field giving the polarization of the forward link Supported values are (from RCS Map Table): 00: linear and horizontal 01: linear and vertical 10: circular left 11: circular right" ::={dvbRcsFwdStatusEntry 7} dvbRcsFwdStatusInnerFec OBJECT-TYPE SYNTAX INTEGER { unknown (-1), fecRate12 (0), fecRate23 (1), fecRate34 (2), fecRate56 (3), fecRate78 (4), fecRate89 (5), fecRate35 (6), fecRate45 (7), fecRate910 (8), fecRate25 (9), fecRate13 (10), fecRate14 (11), noInnerCode (12) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the inner Forward Error Correction used on the forward link for transmission to the RCST. Supported values are: unknown (-1), fecRate1/2 (0), fecRate2/3 (1), fecRate3/4 (2), fecRate5/6 (3), fecRate7/8 (4), fecRate8/9 (5), fecRate3/5 (6), fecRate4/5 (7), fecRate9/10 (8), fecRate2/5 (9), fecRate1/3 (10), fecRate1/4 (11), noInnerCode (12) The RCST will report a value that has been used for transmission to the RCST within the most recent 60 seconds. If this is not relevant, the RCST will report 'unknown'." ::={dvbRcsFwdStatusEntry 8} dvbRcsFwdStatusSymbolRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "x100 symbols/s" MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the symbol rate of the forward link. Its value shall be given in multiples of 100 symbols/s." ::={dvbRcsFwdStatusEntry 9} dvbRcsFwdStatusRolloff OBJECT-TYPE SYNTAX INTEGER { undefRolloff (0), rolloff020 (1), rolloff025 (2), rolloff035 (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the roll-off applied on the forward link. Supported values are: 0: undefined 1: 0.20 2: 0.25 3: 0.35" ::={dvbRcsFwdStatusEntry 10} dvbRcsFwdStatusModulation OBJECT-TYPE SYNTAX INTEGER { unknown (0), mBPSK (1), mQPSK (2), m8PSK (3), m16APSK (4), m32APSK (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the modulation on the forward link used for transmission to the RCST. Supported values are: 0: unknown 1: BPSK 2: QPSK 3: 8PSK 4: 16APSK 5: 32APSK The RCST will report a value that has been used for transmission to the RCST within the most recent 60 seconds. If this is not relevant, the RCST will report 'unknown'." ::={dvbRcsFwdStatusEntry 11} dvbRcsFwdStatusFecFrame OBJECT-TYPE SYNTAX INTEGER { unknown (0), shortframe (1), longframe (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the frame length used on the forward link for transmission to the RCST. Supported values are: 0: Unknown 1: Short frame 2: Normal frame The RCST will report a value that has been used for transmission to the RCST within the most recent 60 seconds. If this is not relevant, the RCST will report 'unknown'." ::={dvbRcsFwdStatusEntry 12} dvbRcsFwdStatusPilot OBJECT-TYPE SYNTAX INTEGER { unknown (0), pilotNotused (1), pilotUsed (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether pilots are used on the forward link for transmission to the RCST. Supported values are: 0: Unknown 1: Pilots are not used 2: Pilots are used The RCST will report a value that has been used for transmission to the RCST within the most recent 60 seconds. If this is not relevant, the RCST will report 'unknown'." ::={dvbRcsFwdStatusEntry 13} dvbRcsFwdStatusBer OBJECT-TYPE SYNTAX Integer32 UNITS "exponent of 10" MAX-ACCESS read-only STATUS current DESCRIPTION "Provides the RCST BER on the Forward Link in log10 units." ::={dvbRcsFwdStatusEntry 14} dvbRcsFwdStatusCnr OBJECT-TYPE SYNTAX Integer32 UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Provides the RCST CNR on the Forward Link in 0.1 dB units." ::={dvbRcsFwdStatusEntry 15} dvbRcsFwdStatusRxPower OBJECT-TYPE SYNTAX Integer32 UNITS "0.1 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Provides the power level of the forward link as received at the IDU, in 0.1 dBm units." DEFVAL { -500 } ::={dvbRcsFwdStatusEntry 16} --============================================================== -- dvbRcsRtnConfig sub-tree object types --============================================================== dvbRcsRtnConfigMaxEirp OBJECT-TYPE SYNTAX Integer32 UNITS "x0.1 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "Max Equivalent Isotropic Radiated Power (EIRP) of the RCST, given in resolution of 0.1 dBm and applied when the IDU can, itself, set the necessary IDU TX output level, e.g., when using a BUC that has a power level detector and that provides sufficient feedback to the IDU." ::= {dvbRcsRtnConfig 1} dvbRcsRtnConfigDefIfLevel OBJECT-TYPE SYNTAX Integer32 UNITS "x0.1 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "IDU TX output level applied in case the dvbRcsRtnConfigMaxEirp cannot be used. The resolution is 0.1 dBm and the accuracy is +/- 1 dBm." ::= {dvbRcsRtnConfig 2} --============================================================== -- dvbRcsRtnStatus sub-tree object types --============================================================== dvbRcsRtnStatusEbN0 OBJECT-TYPE SYNTAX Integer32 UNITS "x0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The EbN0 value reported for the return link, referenced to the regular SYNC burst transmission, in 0.1 dB units." ::= {dvbRcsRtnStatus 1} dvbRcsRtnStatusSFDuration OBJECT-TYPE SYNTAX Unsigned32 (250..7500) UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of the currently applied return link superframe structure, in tenths of milliseconds." ::= {dvbRcsRtnStatus 2} dvbRcsRtnStatusPayloadUnit OBJECT-TYPE SYNTAX INTEGER { unitATM (0), unitMPEG (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if the payload unit used for the return link is ATM or MPEG." ::= {dvbRcsRtnStatus 3} --============================================================= -- conformance information --============================================================= dvbRcsRcstGroups OBJECT IDENTIFIER ::= {dvbRcsConformance 1} dvbRcsRcstCompliances OBJECT IDENTIFIER ::= {dvbRcsConformance 2} --============================================================= -- conformance statements --============================================================= dvbRcsRcstCompliance1 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for DVB-RCS terminals that are compliant with SatLabs System Recommendations. Compliance is linked to the support by the terminal of the options or features defined in the SatLabs System Recommendations. The supported options and features of a terminal are declared in objects dvbRcsSystemSatLabsOptionsDeclaration and dvbRcsSystemSatLabsFeaturesDeclaration respectively." MODULE -- this module MANDATORY-GROUPS {dvbRcsRcstSystemGroup, dvbRcsRcstNetworkGroup, dvbRcsRcstInstallGroup, dvbRcsRcstQosGroup, dvbRcsRcstControlGroup, dvbRcsRcstStateGroup, dvbRcsFwdConfigGroup, dvbRcsFwdStatusGroup, dvbRcsRtnConfigGroup, dvbRcsRtnStatusGroup} GROUP dvbRcsRcstExtNetworkGroup DESCRIPTION "This group is mandatory for an RCST that supports extended networking management functionality. Such RCST is qualified as supporting the EXTNETWORK feature, as defined in the SatLabs System Recommendations." GROUP dvbRcsRcstDnsGroup DESCRIPTION "This group is mandatory for an RCST that supports the DNS protocol. Such RCST is qualified as supporting the DNS option, as defined in the SatLabs System Recommendations." GROUP dvbRcsRcstExtInstallGroup DESCRIPTION "This group is mandatory for an RCST that supports the installation log file. Such RCST is qualified as supporting the INSTALL_LOG feature, as defined in the SatLabs System Recommendations." GROUP dvbRcsRcstEnhancedClassifierGroup DESCRIPTION "This group is mandatory for an RCST that supports the enhanced classifier feature. Such RCST is qualified as supporting the ENHCLASSIFIER feature, as defined in the SatLabs System Recommendations." GROUP dvbRcsRcstMpegQosGroup DESCRIPTION "This group is mandatory for an RCST that supports MPEG traffic bursts. Such RCST is qualified as supporting the MPEG_TRF option, as defined in the SatLabs System Recommendations." GROUP dvbRcsRcstGlobalQosGroup DESCRIPTION "This group is mandatory for an RCST that supports global RCST QoS configuration data. Such RCST is qualified as supporting the RCST_PARA feature, as defined in the SatLabs System Recommendations." GROUP dvbRcsRcstStrictQosGroup DESCRIPTION "This group is mandatory for an RCST that supports strict channel ID dispatching. Such RCST is qualified as supporting the CHID_STRICT option, as defined in the SatLabs System Recommendations." GROUP dvbRcsRcstExtControlGroup DESCRIPTION "This group is mandatory for an RCST that supports extended control management functionality. Such RCST is qualified as supporting the EXTCONTROL feature, as defined in the SatLabs System Recommendations." GROUP dvbRcsRtnExtConfigGroup DESCRIPTION "This group is mandatory for an RCST that supports extended return link configuration management functionality. Such RCST is qualified as supporting the EXTCONFIG feature, as defined in the SatLabs System Recommendations." GROUP dvbRcsRtnExtStatusGroup DESCRIPTION "This group is mandatory for an RCST that supports extended return link status report functionality. Such RCST is qualified as supporting the EXTSTATUS feature, as defined in the SatLabs System Recommendations." GROUP dvbRcsRcstOduListGroup DESCRIPTION "This group is mandatory for an RCST that supports the ODU structural entities defined under dvbRcsOduTx, dvbRcsOduRx, and dvbRcsOduAntenna. Such RCST is qualified as supporting the ODULIST feature, as defined in the SatLabs System Recommendations." OBJECT dvbRcsSystemOduAntennaSize MIN-ACCESS read-only DESCRIPTION "Write access must be supported if dvbRcsRcstOduListGroup is not supported." OBJECT dvbRcsSystemOduAntennaGain MIN-ACCESS read-only DESCRIPTION "Write access must be supported if dvbRcsRcstOduListGroup is not supported." OBJECT dvbRcsSystemOduSspa MIN-ACCESS read-only DESCRIPTION "Write access must be supported if dvbRcsRcstOduListGroup is not supported." OBJECT dvbRcsSystemOduTxType MIN-ACCESS read-only DESCRIPTION "Write access must be supported if dvbRcsRcstOduListGroup is not supported." OBJECT dvbRcsSystemOduRxType MIN-ACCESS read-only DESCRIPTION "Write access must be supported if dvbRcsRcstOduListGroup is not supported." OBJECT dvbRcsSystemOduRxBand MIN-ACCESS read-only DESCRIPTION "Write access must be supported if dvbRcsRcstOduListGroup is not supported." OBJECT dvbRcsSystemOduRxLO MIN-ACCESS read-only DESCRIPTION "Write access must be supported if dvbRcsRcstOduListGroup is not supported." OBJECT dvbRcsSystemOduTxLO MIN-ACCESS read-only DESCRIPTION "Write access must be supported if dvbRcsRcstOduListGroup is not supported." OBJECT dvbRcsNetworkOamInetAddressType SYNTAX InetAddressType { ipv4(1) } DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsNetworkOamInetAddress SYNTAX InetAddress (SIZE(4)) DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsNetworkLanInetAddressType SYNTAX InetAddressType { ipv4(1) } DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsNetworkLanInetAddress SYNTAX InetAddress (SIZE(4)) DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType SYNTAX InetAddressType { ipv4(1) } DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress SYNTAX InetAddress (SIZE(4)) DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsPrimaryDnsServerInetAddressType SYNTAX InetAddressType { ipv4(1) } DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsPrimaryDnsServerInetAddress SYNTAX InetAddress (SIZE(4)) DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsSecondaryDnsServerInetAddressType SYNTAX InetAddressType { ipv4(1) } DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsSecondaryDnsServerInetAddress SYNTAX InetAddress (SIZE(4)) DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsNetworkNccMgtInetAddressType SYNTAX InetAddressType { ipv4(1) } DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsNetworkNccMgtInetAddress SYNTAX InetAddress (SIZE(4)) DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsPktClassDscpLow MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports the enhanced classifier feature. Such RCST is qualified as supporting the ENHCLASSIFIER feature, as defined in the SatLabs System Recommendations." OBJECT dvbRcsPktClassDscpHigh MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports the enhanced classifier feature. Such RCST is qualified as supporting the ENHCLASSIFIER feature, as defined in the SatLabs System Recommendations." OBJECT dvbRcsPktClassDscpMarkValue MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports the enhanced classifier feature. Such RCST is qualified as supporting the ENHCLASSIFIER feature, as defined in the SatLabs System Recommendations." OBJECT dvbRcsPktClassSrcInetAddressType SYNTAX InetAddressType { ipv4(1) } DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsPktClassSrcInetAddress SYNTAX InetAddress (SIZE(4)) DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsPktClassDstInetAddressType SYNTAX InetAddressType { ipv4(1) } DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsPktClassDstInetAddress SYNTAX InetAddress (SIZE(4)) DESCRIPTION "An implementation is only required to support IPv4 addresses." OBJECT dvbRcsPhbName MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support. Such RCST is qualified as supporting the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsPhbRequestClassAssociation MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support. Such RCST is qualified as supporting the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsPhbMappingRowStatus MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support. Such RCST is qualified as supporting the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassName MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support. Such RCST is qualified as supporting the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassChanId MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support. Such RCST is qualified as supporting the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassVccVpi MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support. Such RCST is qualified as supporting the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassVccVci MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support. Such RCST is qualified as supporting the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassPidPoolReference MIN-ACCESS not-accessible DESCRIPTION "Read-only access required if the RCST supports MPEG traffic bursts, according to the MPEG_TRF option, as defined in the SatLabs System Recommendations. Create access only required if the RCST also supports extended management support, according to the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassCra MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support, according to the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassRbdcMax MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support, according to the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassRbdcTimeout MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support, according to the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassVbdcMax MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support, according to the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassVbdcTimeout MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support, according to the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassVbdcMaxBackLog MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support, according to the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsRequestClassRowStatus MIN-ACCESS read-only DESCRIPTION "Create access only required if the RCST supports extended management support, according to the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsPidValue MIN-ACCESS not-accessible DESCRIPTION "Read-only access required if the RCST supports MPEG traffic bursts, according to the MPEG_TRF option, as defined in the SatLabs System Recommendations. Create access only required if the RCST also supports extended management support, according to the SNMPMISC option, as defined in the SatLabs System Recommendations." OBJECT dvbRcsPidPoolRowStatus MIN-ACCESS not-accessible DESCRIPTION "Read-only access required if the RCST supports MPEG traffic bursts, according to the MPEG_TRF option, as defined in the SatLabs System Recommendations. Create access only required if the RCST also supports extended management support, according to the SNMPMISC option, as defined in the SatLabs System Recommendations." ::= {dvbRcsRcstCompliances 1} --============================================================= -- units of conformance --============================================================= --============================================================= -- object groups for RCST system --============================================================= dvbRcsRcstSystemGroup OBJECT-GROUP OBJECTS { dvbRcsSystemMibRevision, dvbRcsSystemSatLabsProfilesDeclaration, dvbRcsSystemSatLabsOptionsDeclaration, dvbRcsSystemSatLabsFeaturesDeclaration, dvbRcsSystemLocation, dvbRcsSystemOduAntennaSize, dvbRcsSystemOduAntennaGain, dvbRcsSystemOduSspa, dvbRcsSystemOduTxType, dvbRcsSystemOduRxType, dvbRcsSystemOduRxBand, dvbRcsSystemOduRxLO, dvbRcsSystemOduTxLO, dvbRcsTcpPep, dvbRcsHttpPep } STATUS current DESCRIPTION "A collection of objects providing information applicable for basic device management support." ::= {dvbRcsRcstGroups 1} --============================================================= -- object groups for RCST networking --============================================================= dvbRcsRcstNetworkGroup OBJECT-GROUP OBJECTS { dvbRcsNetworkOamInetAddressType, dvbRcsNetworkOamInetAddress, dvbRcsNetworkOamInetAddressPrefixLength, dvbRcsNetworkLanInetAddressType, dvbRcsNetworkLanInetAddress, dvbRcsNetworkLanInetAddressPrefixLength, dvbRcsNetworkConfigFileDownloadUrl, dvbRcsNetworkConfigFileUploadUrl, dvbRcsNetworkLogFileUploadUrl } STATUS current DESCRIPTION "A collection of objects providing basic networking management support." ::= {dvbRcsRcstGroups 2} dvbRcsRcstExtNetworkGroup OBJECT-GROUP OBJECTS { dvbRcsNetworkOamInetAddressAssign, dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType, dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress, dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressPrefixLength, dvbRcsNetworkNccMgtInetAddressType, dvbRcsNetworkNccMgtInetAddress, dvbRcsNetworkNccMgtInetAddressPrefixLength } STATUS current DESCRIPTION "A collection of objects providing extended networking management support." ::= {dvbRcsRcstGroups 3} dvbRcsRcstDnsGroup OBJECT-GROUP OBJECTS { dvbRcsPrimaryDnsServerInetAddressType, dvbRcsPrimaryDnsServerInetAddress, dvbRcsPrimaryDnsServerInetAddressPrefixLength, dvbRcsSecondaryDnsServerInetAddressType, dvbRcsSecondaryDnsServerInetAddress, dvbRcsSecondaryDnsServerInetAddressPrefixLength } STATUS current DESCRIPTION "A collection of objects providing DNS management support." ::= {dvbRcsRcstGroups 4} --============================================================= -- object groups for RCST installation --============================================================= dvbRcsRcstInstallGroup OBJECT-GROUP OBJECTS { dvbRcsInstallAntennaAlignmentState, dvbRcsInstallCwFrequency, dvbRcsInstallCwMaxDuration, dvbRcsInstallCwPower, dvbRcsInstallCoPolReading, dvbRcsInstallXPolReading, dvbRcsInstallCoPolTarget, dvbRcsInstallXPolTarget, dvbRcsInstallStandByDuration, dvbRcsInstallTargetEsN0 } STATUS current DESCRIPTION "A collection of objects providing information applicable for basic installation support." ::= {dvbRcsRcstGroups 5} dvbRcsRcstExtInstallGroup OBJECT-GROUP OBJECTS { dvbRcsNetworkInstallLogFileDownloadUrl, dvbRcsNetworkInstallLogFileUploadUrl } STATUS current DESCRIPTION "A collection of objects providing extended device installation support." ::= {dvbRcsRcstGroups 6} --============================================================= -- object groups for QoS --============================================================= dvbRcsRcstQosGroup OBJECT-GROUP OBJECTS { dvbRcsPktClassDscpLow, dvbRcsPktClassDscpHigh, dvbRcsPktClassDscpMarkValue, dvbRcsPktClassPhbAssociation, dvbRcsPktClassRowStatus, dvbRcsPhbName, dvbRcsPhbRequestClassAssociation, dvbRcsPhbMappingRowStatus, dvbRcsRequestClassName, dvbRcsRequestClassChanId, dvbRcsRequestClassVccVpi, dvbRcsRequestClassVccVci, dvbRcsRequestClassCra, dvbRcsRequestClassRbdcMax, dvbRcsRequestClassRbdcTimeout, dvbRcsRequestClassVbdcMax, dvbRcsRequestClassVbdcTimeout, dvbRcsRequestClassVbdcMaxBackLog, dvbRcsRequestClassRowStatus } STATUS current DESCRIPTION "A collection of objects providing basic access to QoS configuration data." ::= {dvbRcsRcstGroups 7} dvbRcsRcstEnhancedClassifierGroup OBJECT-GROUP OBJECTS { dvbRcsPktClassIpProtocol, dvbRcsPktClassSrcInetAddressType, dvbRcsPktClassSrcInetAddress, dvbRcsPktClassSrcInetAddressPrefixLength, dvbRcsPktClassDstInetAddressType, dvbRcsPktClassDstInetAddress, dvbRcsPktClassDstInetAddressPrefixLength, dvbRcsPktClassSrcPortLow, dvbRcsPktClassSrcPortHigh, dvbRcsPktClassDstPortLow, dvbRcsPktClassDstPortHigh, dvbRcsPktClassVlanUserPri } STATUS current DESCRIPTION "A collection of objects providing support for management of the enhanced classifier." ::= {dvbRcsRcstGroups 8} dvbRcsRcstMpegQosGroup OBJECT-GROUP OBJECTS { dvbRcsRequestClassPidPoolReference, dvbRcsPidValue, dvbRcsPidPoolRowStatus } STATUS current DESCRIPTION "A collection of objects providing access to MPEG-related link QoS configuration data." ::= {dvbRcsRcstGroups 9} dvbRcsRcstGlobalQosGroup OBJECT-GROUP OBJECTS { dvbRcsQosGlobalRbdcMax, dvbRcsQosGlobalVbdcMax, dvbRcsQosGlobalVbdcMaxBackLog } STATUS current DESCRIPTION "A collection of objects providing access to global RCST QoS configuration data." ::= {dvbRcsRcstGroups 10} dvbRcsRcstStrictQosGroup OBJECT-GROUP OBJECTS { dvbRcsQosChannelIdStrictDispatching } STATUS current DESCRIPTION "A collection of objects allowing management of strict channel ID dispatching." ::= {dvbRcsRcstGroups 11} --============================================================= -- object groups for RCST control --============================================================= dvbRcsRcstControlGroup OBJECT-GROUP OBJECTS { dvbRcsCtrlRebootCommand, dvbRcsCtrlUserTrafficDisable, dvbRcsCtrlCwEnable, dvbRcsCtrlDownloadFileCommand, dvbRcsCtrlUploadFileCommand, dvbRcsCtrlActivateConfigFileCommand, dvbRcsCtrlRcstRxReacquire } STATUS current DESCRIPTION "A collection of objects allowing basic RCST control." ::= {dvbRcsRcstGroups 12} dvbRcsRcstExtControlGroup OBJECT-GROUP OBJECTS { dvbRcsCtrlRcstTxDisable, dvbRcsCtrlOduTxReferenceEnable, dvbRcsCtrlOduTxDCEnable, dvbRcsCtrlOduRxDCEnable, dvbRcsCtrlRcstLogonCommand, dvbRcsCtrlRcstLogoffCommand } STATUS current DESCRIPTION "A collection of objects allowing extended RCST control." ::= {dvbRcsRcstGroups 13} --============================================================= -- object groups for RCST state --============================================================= dvbRcsRcstStateGroup OBJECT-GROUP OBJECTS { dvbRcsRcstMode, dvbRcsRcstFaultStatus, dvbRcsRcstFwdLinkStatus, dvbRcsRcstLogUpdated, dvbRcsRcstCurrentSoftwareVersion, dvbRcsRcstAlternateSoftwareVersion, dvbRcsRcstActivatedConfigFileVersion, dvbRcsRcstDownloadedConfigFileVersion } STATUS current DESCRIPTION "A collection of objects allowing access to RCST state." ::= {dvbRcsRcstGroups 14} --============================================================= -- object groups for forward link --============================================================= dvbRcsFwdConfigGroup OBJECT-GROUP OBJECTS { dvbRcsFwdStartPopId, dvbRcsFwdStartFrequency, dvbRcsFwdStartPolar, dvbRcsFwdStartFormat, dvbRcsFwdStartRolloff, dvbRcsFwdStartSymbolRate, dvbRcsFwdStartInnerFec, dvbRcsFwdStartRowStatus } STATUS current DESCRIPTION "A collection of objects providing basic start forward link configuration support." ::= {dvbRcsRcstGroups 15} dvbRcsFwdStatusGroup OBJECT-GROUP OBJECTS { dvbRcsFwdStatusPopId, dvbRcsFwdStatusIfReference, dvbRcsFwdStatusNetId, dvbRcsFwdStatusNetName, dvbRcsFwdStatusFormat, dvbRcsFwdStatusFrequency, dvbRcsFwdStatusPolar, dvbRcsFwdStatusInnerFec, dvbRcsFwdStatusSymbolRate, dvbRcsFwdStatusRolloff, dvbRcsFwdStatusModulation, dvbRcsFwdStatusFecFrame, dvbRcsFwdStatusPilot, dvbRcsFwdStatusBer, dvbRcsFwdStatusCnr, dvbRcsFwdStatusRxPower } STATUS current DESCRIPTION "A collection of objects providing forward link status." ::= {dvbRcsRcstGroups 16} --============================================================= -- object groups for return link --============================================================= dvbRcsRtnConfigGroup OBJECT-GROUP OBJECTS { dvbRcsRtnConfigDefIfLevel } STATUS current DESCRIPTION "A collection of objects providing basic return link configuration support." ::= {dvbRcsRcstGroups 17} dvbRcsRtnExtConfigGroup OBJECT-GROUP OBJECTS { dvbRcsRtnConfigMaxEirp } STATUS current DESCRIPTION "A collection of objects providing extended return link configuration support." ::= {dvbRcsRcstGroups 18} dvbRcsRtnStatusGroup OBJECT-GROUP OBJECTS { dvbRcsRtnStatusPayloadUnit } STATUS current DESCRIPTION "A collection of objects allowing access to return link status." ::= {dvbRcsRcstGroups 19} dvbRcsRtnExtStatusGroup OBJECT-GROUP OBJECTS { dvbRcsRcstRtnLinkStatus, dvbRcsRtnStatusEbN0, dvbRcsRtnStatusSFDuration } STATUS current DESCRIPTION "A collection of objects allowing access to extended return link status." ::= {dvbRcsRcstGroups 20} dvbRcsRcstOduListGroup OBJECT-GROUP OBJECTS { dvbRcsOduTxTypeDescription, dvbRcsOduTxType, dvbRcsOduRxTypeDescription, dvbRcsOduRxType, dvbRcsOduAntennaTypeDescription, dvbRcsOduAntennaType } STATUS current DESCRIPTION "A collection of objects supporting flexible selection of ODU devices." ::= {dvbRcsRcstGroups 21} END