G9983-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2, Unsigned32, Counter32 FROM SNMPv2-SMI -- RFC 2578 TEXTUAL-CONVENTION, RowStatus, TruthValue FROM SNMPv2-TC -- RFC 2579 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC 2580 ifIndex, InterfaceIndex FROM IF-MIB -- RFC 2863 HCPerfCurrentCount, HCPerfIntervalCount, HCPerfValidIntervals, HCPerfInvalidIntervals, HCPerfTimeElapsed FROM HC-PerfHist-TC-MIB -- RFC 3705 ; ------------------------------------------------------------------------ g9983MIB MODULE-IDENTITY LAST-UPDATED "201302200000Z" -- 20 February 2013 ORGANIZATION "IETF ADSL MIB Working Group" CONTACT-INFO "WG charter: http://datatracker.ietf.org/wg/adslmib/charter/ Mailing Lists: General Discussion: [email protected] To Subscribe: [email protected] In Body: subscribe your_email_address Chair: Menachem Dodge Postal: ECI Telecom, Ltd. 30 Hasivim St. Petach-Tikva 4951169 Israel Phone: +972-3-926-8421 EMail: [email protected] Editor: Edward Beili Postal: Actelis Networks, Inc. 25 Bazel St., P.O.B. 10173 Petach-Tikva 49103 Israel Phone: +972-3-924-3491 EMail: [email protected]" DESCRIPTION "The objects in this MIB module are used to manage the multi-pair bonded xDSL interfaces using time-division inverse multiplexing (TDIM), as defined in ITU-T Recommendation G.998.3 (G.Bond/TDIM). This MIB module MUST be used in conjunction with the GBOND-MIB module, common to all G.Bond technologies. The following references are used throughout this MIB module: [G.998.3] refers to: ITU-T Recommendation G.998.3: 'Multi-pair bonding using time-division inverse multiplexing', January 2005. [TR-159] refers to: Broadband Forum Technical Report: 'Management Framework for xDSL Bonding', December 2008. Naming Conventions: BCE - Bonding Channel Entity BTU - Bonding Terminating Unit BTU-C - Bonding Terminating Unit, CO side BTU-R - Bonding Terminating Unit, Remote Terminal (CPE) side CO - Central Office CPE - Customer Premises Equipment GBS - Generic Bonding Sub-layer GBS-C - Generic Bonding Sub-layer, CO side GBS-R - Generic Bonding Sub-layer, Remote Terminal (CPE) side SNR - Signal to Noise Ratio Copyright (c) 2013 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info)." REVISION "201302200000Z" -- 20 February 2013 DESCRIPTION "Initial version, published as RFC 6766." ::= { mib-2 210 } -- Sections of the module -- Structured as recommended by RFC 4181, Appendix D g9983Objects OBJECT IDENTIFIER ::= { g9983MIB 1 } g9983Conformance OBJECT IDENTIFIER ::= { g9983MIB 2 } -- Groups in the module g9983Port OBJECT IDENTIFIER ::= { g9983Objects 1 } -- Textual Conventions G9983SvcIndex ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "A unique value, greater than zero, for each service defined in the managed G.Bond/TDIM port. It is RECOMMENDED that values be assigned contiguously starting from 1. The value for each service MUST remain constant at least from one re-initialization of the local management subsystem to the next re-initialization." SYNTAX Unsigned32 (1..255) G9983SvcIndexList ::= TEXTUAL-CONVENTION DISPLAY-HINT "1d:" STATUS current DESCRIPTION "This textual convention represents a continuous ordered list of all the services defined for the managed G.Bond/TDIM port. The value of this object is a concatenation of zero or more (up to 60) octets, where each octet contains an 8-bit G9983SvcIndex value, identifying a particular service. An octet's position reflects the associated service position and its priority in the G.Bond/TDIM frame, with the first octet being the first service of highest priority. A zero-length octet string is object-specific and MUST therefore be defined as part of the description of any object that uses this syntax. Examples of the usage of a zero-length value might include situations where an object using this textual convention is irrelevant for a specific G.Bond/TDIM port type or where no services have been defined for this port." SYNTAX OCTET STRING (SIZE (0..60)) G9983SvcOrderIndex ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "A unique value, greater than zero, for each service defined in the managed G.Bond/TDIM port, showing its relative position inside the G.Bond/TDIM frame." SYNTAX Unsigned32 (1..60) -- Port Notifications group g9983PortNotifications OBJECT IDENTIFIER ::= { g9983Port 0 } g9983SvcUp NOTIFICATION-TYPE OBJECTS { -- ifIndex and g9983OperSvcPosition would be part of the trap OID g9983OperSvcIdx, g9983SvcIfIdx } STATUS current DESCRIPTION "This notification indicates that a service, indicated by the g9983OperSvcIdx (mapped to a particular interface indicated by the g9983SvcIfIdx), in a particular G.Bond/TDIM port is passing traffic. This notification is generated (unless disabled or dropped by the rate-limiting mechanism) when the g9983OperSvcState object has left the 'down' state, while the G.Bond/TDIM port state (the ifOperStatus of the IF-MIB) is 'up'. Generation of this notification is controlled by the g9983PortConfSvcUpDownEnable object. This object maps to the TR-159 notification nServiceUp." REFERENCE "[TR-159], Section 5.5.5.7" ::= { g9983PortNotifications 1 } g9983SvcDown NOTIFICATION-TYPE OBJECTS { -- ifIndex and g9983OperSvcPosition would be part of the trap OID g9983OperSvcIdx, g9983SvcIfIdx } STATUS current DESCRIPTION "This notification indicates that a service indicated by the g9983OperSvcIdx (mapped to a particular interface indicated by the g9983SvcIfIdx) in a particular G.Bond/TDIM port has stopped passing traffic. This notification is generated (unless disabled or dropped by the rate-limiting mechanism), when the g9983OperSvcState object has entered the 'down' state, while the G.Bond/TDIM port state (the ifOperStatus of the IF-MIB) is 'up'. Generation of this notification is controlled by the g9983PortConfSvcUpDownEnable object. This object maps to the TR-159 notification nServiceDown." REFERENCE "[TR-159], Section 5.5.5.8" ::= { g9983PortNotifications 2 } -- G.Bond/TDIM Port group g9983PortConfTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983PortConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for configuration of G.Bond/TDIM ports. Entries in this table MUST be maintained in a persistent manner." ::= { g9983Port 1 } g9983PortConfEntry OBJECT-TYPE SYNTAX G9983PortConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Port Configuration table. Each entry represents a G.Bond/TDIM port indexed by the ifIndex. Additional configuration parameters are available via the gBondPortConfEntry of the GBOND-MIB. Note that a G.Bond/TDIM port runs on top of a single or multiple BCE port(s), which are also indexed by the ifIndex." INDEX { ifIndex } ::= { g9983PortConfTable 1 } G9983PortConfEntry ::= SEQUENCE { g9983PortConfFecAdminState TruthValue, g9983PortConfFecWordSize Unsigned32, g9983PortConfFecRedundancySize Unsigned32, g9983PortConfFecInterleaverType INTEGER, g9983PortConfFecInterleaverDepth Unsigned32, g9983PortConfAdminServices G9983SvcIndexList, g9983PortConfSvcUpDownEnable TruthValue } g9983PortConfFecAdminState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A desired state of the OPTIONAL Forward Error Correction (FEC) function of the G.Bond/TDIM port. A value of 'false' indicates that the FEC function SHALL be disabled. A value of 'true' indicates that the FEC function SHALL be enabled, if supported by the G.Bond/TDIM port, as indicated by the g9983PortCapFecSupported object. The g9983PortStatFecOperState object indicates the current operational state of the FEC function. For the GBS-R ports, the value of this object cannot be changed directly. This value may be changed as a result of a write operation on the g9983PortCapFecSupported object of a remote GBS-C. Modifications of this object MUST be performed when the link is 'down'. Attempts to change this object MUST be rejected if the link is 'up' or initializing, or if it is a GBS-R. This object maps to the TR-159/G.998.3 attribute aFECAdminState." REFERENCE "[TR-159], Section 5.5.4.5; [G.998.3], Appendix II, B-X" ::= { g9983PortConfEntry 1 } g9983PortConfFecWordSize OBJECT-TYPE SYNTAX Unsigned32 (0|20..255) UNITS "octets" MAX-ACCESS read-write STATUS current DESCRIPTION "A FEC code word size, in octets, for G.Bond/TDIM ports supporting the FEC function. This object is read-write for the GBS-C ports and read-only for the GBS-R. A value of zero SHALL be returned if the FEC function is disabled (via g9983PortConfFecAdminState) or not supported. Changing of the FEC code word size MUST be performed when the FEC-enabled link is 'down'. Attempts to change this object MUST be rejected if the link is 'up' or initializing or if the FEC function is disabled/not supported. This object maps to the TR-159/G.998.3 attribute aFECWordSize." REFERENCE "[TR-159], Section 5.5.4.7; [G.998.3], Appendix II, B-XI" ::= { g9983PortConfEntry 2 } g9983PortConfFecRedundancySize OBJECT-TYPE SYNTAX Unsigned32 (0|2|4|8|16|20) UNITS "octets" MAX-ACCESS read-write STATUS current DESCRIPTION "A FEC redundancy word size, in octets, for G.Bond/TDIM ports supporting the FEC function. This object is read-write for the GBS-C ports and read-only for the GBS-R. A value of zero SHALL be returned if the FEC function is disabled (via g9983PortConfFecAdminState) or not supported. Changing of the FEC redundancy word size MUST be performed when the FEC-enabled link is 'down'. Attempts to change this object MUST be rejected if the link is 'up' or initializing or if the FEC function is disabled/not supported. This object maps to the TR-159/G.998.3 attribute aFECRedundancySize." REFERENCE "[TR-159], Section 5.5.4.8; [G.998.3], Appendix II, B-XII" ::= { g9983PortConfEntry 3 } g9983PortConfFecInterleaverType OBJECT-TYPE SYNTAX INTEGER { none(0), block(1), convolution(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "An Interleaver type for G.Bond/TDIM ports supporting the FEC function. This object is read-write for the GBS-C ports and read-only for the GBS-R. A value of none(0) SHALL be returned if the FEC function is disabled (via g9983PortConfFecAdminState) or not supported. Changing of the Interleaver type MUST be performed when the FEC-enabled link is 'down'. Attempts to change this object MUST be rejected if the link is 'up' or initializing or if the FEC function is disabled/not supported. This object maps to the TR-159/G.998.3 attribute aFECInterleaverType." REFERENCE "[TR-159], Section 5.5.4.9; [G.998.3], Appendix II, B-XIII" ::= { g9983PortConfEntry 4 } g9983PortConfFecInterleaverDepth OBJECT-TYPE SYNTAX Unsigned32 (0|1|2|3|4|6|8|12|16|24|32|48|96) MAX-ACCESS read-write STATUS current DESCRIPTION "An Interleaver depth for G.Bond/TDIM ports supporting the FEC function. This object is read-write for the GBS-C ports and read-only for the GBS-R. A value of zero SHALL be returned if the FEC function is disabled (via g9983PortConfFecAdminState) or not supported. Changing of the Interleaver depth MUST be performed when the FEC-enabled link is 'down'. Attempts to change this object MUST be rejected if the link is 'up' or initializing or if the FEC function is disabled/not supported. This object maps to the TR-159/G.998.3 attribute aFECInterleaverDepth." REFERENCE "[TR-159], Section 5.5.4.10; [G.998.3], Appendix II, B-XIV" ::= { g9983PortConfEntry 5 } g9983PortConfAdminServices OBJECT-TYPE SYNTAX G9983SvcIndexList MAX-ACCESS read-write STATUS current DESCRIPTION "Desired list of services for a G.Bond/TDIM port. This object is a list of pointers to entries in the g9983SvcTable. The value of this object is a continuous ordered list of up to 60 indices (g9983SvcIdx) of the active services carried via the G.Bond/TDIM link. The position of a service in the list determines its relative priority in cases of bandwidth degradation -- the priority decreases towards the end of the list, which means that the last service in the list would be suspended first when the bandwidth degrades. This object is writable and readable for the GBS-C ports. It is irrelevant for the GBS-R ports -- a zero-length octet string SHALL be returned on an attempt to read this object, and an attempt to change this object MUST be rejected in this case. Note that the current operational service list is available via the g9983OperSvcTable object. This object for a GBS-C port MAY be modified independently of the link's state, i.e., in-service and out-of-service. Attempts to set this object to a list with a member value that is not the value of the index for an active entry in the corresponding g9983SvcTable table MUST be rejected." REFERENCE "[G.998.3], Sections 10.2.3, 13.3.4.6-13.3.4.11" ::= { g9983PortConfEntry 6 } g9983PortConfSvcUpDownEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether g9983SvcUp and g9983SvcDown notifications should be generated for this interface. A value of true(1) indicates that the notifications are enabled. A value of false(2) indicates that the notifications are disabled. This object maps to the TR-159 attribute aServiceUpDownEnable." REFERENCE "[TR-159], Section 5.5.5.6" ::= { g9983PortConfEntry 7 } g9983PortCapTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983PortCapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for capabilities of G.Bond/TDIM ports. Entries in this table MUST be maintained in a persistent manner." ::= { g9983Port 2 } g9983PortCapEntry OBJECT-TYPE SYNTAX G9983PortCapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Port Capability table. Each entry represents a G.Bond/TDIM port indexed by the ifIndex. Additional capabilities are available via the gBondPortCapabilityEntry of the GBOND-MIB. Note that a G.Bond/TDIM port runs on top of a single or multiple BCE port(s), which are also indexed by the ifIndex." INDEX { ifIndex } ::= { g9983PortCapTable 1 } G9983PortCapEntry ::= SEQUENCE { g9983PortCapFecSupported TruthValue, g9983PortCapFecMaxWordSize Unsigned32, g9983PortCapFecMaxRedundancySize Unsigned32, g9983PortCapFecInterleaverTypeSupported INTEGER, g9983PortCapFecMaxInterleaverDepth Unsigned32 } g9983PortCapFecSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "FEC and Interleaver capability of the G.Bond/TDIM port. This object has a value of true(1) when the port supports the FEC and Interleaver function. A value of false(2) is returned when the port does not support the FEC and Interleaver function. This object maps to the TR-159/G.998.3 attribute aFECSupported." REFERENCE "[TR-159], Section 5.5.4.4; [G.998.3], Appendix II, B-VI" ::= { g9983PortCapEntry 1 } g9983PortCapFecMaxWordSize OBJECT-TYPE SYNTAX Unsigned32 (0|20..255) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "A maximum supported FEC code word size, in octets, for G.Bond/TDIM ports supporting the FEC function. A value of zero SHALL be returned if the FEC function is not supported. This object maps to the TR-159 attribute aFECWordSize." REFERENCE "[TR-159], Section 5.5.4.11; [G.998.3], Appendix II, B-XI" ::= { g9983PortCapEntry 2 } g9983PortCapFecMaxRedundancySize OBJECT-TYPE SYNTAX Unsigned32 (0|2|4|8|16|20) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "A maximum supported FEC redundancy word size, in octets, for G.Bond/TDIM ports supporting the FEC function. A value of zero SHALL be returned if the FEC function is not supported. This object maps to the TR-159 attribute aFECMaxRedundancySize." REFERENCE "[TR-159], Section 5.5.4.12; [G.998.3], Appendix II, B-XII" ::= { g9983PortCapEntry 3 } g9983PortCapFecInterleaverTypeSupported OBJECT-TYPE SYNTAX INTEGER { none(0), block(1), convolution(2), blockConvolution(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Supported Interleaver types for G.Bond/TDIM ports supporting the FEC function. Possible values are: none - the port does not support interleaving block - the port supports Block Interleaver convolution - the port supports Convolution Interleaver blockConvolution - the port supports both Block Interleaver and Convolution Interleaver This object maps to the TR-159 attribute aFECInterleaverTypesSupported." REFERENCE "[TR-159], Section 5.5.4.13; [G.998.3], Appendix II, B-XIII" ::= { g9983PortCapEntry 4 } g9983PortCapFecMaxInterleaverDepth OBJECT-TYPE SYNTAX Unsigned32 (0|1|2|3|4|6|8|12|16|24|32|48|96) MAX-ACCESS read-only STATUS current DESCRIPTION "A maximum Interleaver depth for G.Bond/TDIM ports supporting the FEC function. A value of zero SHALL be returned if the Interleaver is not supported. This object maps to the TR-159 attribute aFECMaxInterleaverDepth." REFERENCE "[TR-159], Section 5.5.4.14; [G.998.3], Appendix II, B-XIV" ::= { g9983PortCapEntry 5 } g9983PortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983PortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides overall status information of G.Bond TDIM ports, complementing the generic status information from the ifTable of the IF-MIB and the gBondPortStatFltStatus of the GBOND-MIB. Additional status information about connected BCEs is available from the relevant line MIBs. This table contains live data from the equipment. As such, it is NOT persistent." ::= { g9983Port 3 } g9983PortStatEntry OBJECT-TYPE SYNTAX G9983PortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Port Status table. Each entry represents a G.Bond/TDIM port indexed by the ifIndex. Note that a G.Bond GBS port runs on top of a single or multiple BCE port(s), which are also indexed by the ifIndex." INDEX { ifIndex } ::= { g9983PortStatTable 1 } G9983PortStatEntry ::= SEQUENCE { g9983PortStatFecOperState TruthValue, g9983PortStatFltStatus BITS, g9983PortStatCrc4Errors Counter32, g9983PortStatCrc6Errors Counter32, g9983PortStatCrc8Errors Counter32 } g9983PortStatFecOperState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value indicating the current operational state of the OPTIONAL Forward Error Correction (FEC) function for the G.998.3 port. A value of 'false' indicates that the FEC function is disabled. A value of 'true' indicates that the FEC function is enabled (and supported). This object maps to the TR-159 attribute aFECOperState." REFERENCE "[TR-159], Section 5.5.4.6" ::= { g9983PortStatEntry 1 } g9983PortStatFltStatus OBJECT-TYPE SYNTAX BITS { serviceDown(0), wrongConfig(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "G.Bond/TDIM port fault status. This is a bitmap of possible conditions. The various bit positions are: serviceDown - at least one of the services defined for this aggregation group is down (due to low rate). wrongConfig - at least one BCE at the remote GBS-R is already connected to another GBS. This object is intended to supplement the ifOperStatus object in the IF-MIB and the gBondPortStatFltStatus object in the GBOND-MIB." REFERENCE "[G.998.3], Section 6.3; RFC 2863, IF-MIB, ifOperStatus; RFC 6765, GBOND-MIB, gBondPortStatFltStatus" ::= { g9983PortStatEntry 2 } g9983PortStatCrc4Errors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of CRC-4 errors (frame header errors) on all pairs in the G.Bond/TDIM port. Simultaneous errors on M lines SHOULD be counted M times. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime as defined in the IF-MIB. This object maps to the TR-159/G.998.3 attribute aCRC4Errors." REFERENCE "[TR-159], Section 5.5.4.1; [G.998.3], Appendix II, B-VII" ::= { g9983PortStatEntry 3 } g9983PortStatCrc6Errors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of CRC-6 errors (super-frame errors) on all pairs in the G.Bond/TDIM port. Simultaneous errors on M lines SHOULD be counted 1 time. Discontinuities in the value of this counter can occur at re-initialization of the local management subsystem, and at other times as indicated by the value of ifCounterDiscontinuityTime as defined in the IF-MIB. This object maps to the TR-159/G.998.3 attribute aCRC6Errors." REFERENCE "[TR-159], Section 5.5.4.2; [G.998.3], Appendix II, B-VIII" ::= { g9983PortStatEntry 4 } g9983PortStatCrc8Errors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of CRC-8 errors (event/message errors) on all pairs in the G.Bond/TDIM port. Simultaneous errors on M lines SHOULD be counted M times. Discontinuities in the value of this counter can occur at re-initialization of the local management subsystem, and at other times as indicated by the value of ifCounterDiscontinuityTime as defined in the IF-MIB. This object maps to the TR-159/G.998.3 attribute aCRC8Errors." REFERENCE "[TR-159], Section 5.5.4.3; [G.998.3], Appendix II, B-IX" ::= { g9983PortStatEntry 5 } g9983OperSvcTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983OperSvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of the operational services configured on a G.Bond/TDIM port. This table reflects current actual service configuration, set by the g9983PortConfAdminServices object. The number of entries (services) in this table therefore can vary between 0, when no services are configured, and 60, for the maximum number of services. This table contains live data from the equipment. As such, it is NOT persistent." ::= { g9983Port 4 } g9983OperSvcEntry OBJECT-TYPE SYNTAX G9983OperSvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Port Operational Service table, containing the index of an active service entry in the g9983SvcTable. The entry is indexed by the ifIndex, indicating a corresponding G.Bond/TDIM port, and by g9983OperSvcPosition (1..60), indicating the corresponding service position in the G.Bond/TDIM frame." INDEX { ifIndex, g9983OperSvcPosition } ::= { g9983OperSvcTable 1 } G9983OperSvcEntry ::= SEQUENCE { g9983OperSvcPosition G9983SvcOrderIndex, g9983OperSvcIdx G9983SvcIndex, g9983OperSvcState INTEGER } g9983OperSvcPosition OBJECT-TYPE SYNTAX G9983SvcOrderIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "G.Bond/TDIM operational service position -- a unique index, indicating relative placement of the associated service pointed to by g9983OperSvcIdx, within the G.Bond/TDIM frame. There can be up to 60 services defined over a TDIM bonded facility. Services with lower indices have higher priority in cases of bandwidth degradation. The value of g9983OperSvcPosition for the first g9983OperSvcEntry is always 1, incrementing sequentially for each consecutive entry, i.e., 2 for the second entry, 3 for the third, etc. This objects maps to the TR-159/G.998.3 attribute aServiceID." REFERENCE "[TR-159], Section 5.5.5.1; [G.998.3], Appendix II, C-I" ::= { g9983OperSvcEntry 1 } g9983OperSvcIdx OBJECT-TYPE SYNTAX G9983SvcIndex MAX-ACCESS read-only STATUS current DESCRIPTION "G.Bond/TDIM operational service index -- a read-only pointer to an existing entry in the g9983SvcTable (value of g9983SvcIdx) describing a particular service." ::= { g9983OperSvcEntry 2 } g9983OperSvcState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "G.Bond/TDIM service operational state. Possible values are: up - Service is up and passing traffic. down - Service is down, due to a variety of reasons, e.g., G.Bond/TDIM port is down, current link bandwidth is too low to support a particular service, etc. This objects maps to the TR-159 attribute aServiceOperState." REFERENCE "[TR-159], Section 5.5.5.5" ::= { g9983OperSvcEntry 3 } g9983SvcTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983SvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of possible services for G.Bond/TDIM ports. Entries in this table MUST be maintained in a persistent manner." ::= { g9983Port 5 } g9983SvcEntry OBJECT-TYPE SYNTAX G9983SvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Port Service table, containing the management information applicable to a particular service, indexed by the g9983SvcIdx, on a G.Bond/TDIM port, indexed by the ifIndex." INDEX { ifIndex, g9983SvcIdx } ::= { g9983SvcTable 1 } G9983SvcEntry ::= SEQUENCE { g9983SvcIdx G9983SvcIndex, g9983SvcIfIdx InterfaceIndex, g9983SvcType INTEGER, g9983SvcSize Unsigned32, g9983SvcRowStatus RowStatus } g9983SvcIdx OBJECT-TYPE SYNTAX G9983SvcIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "G.Bond/TDIM service index -- a unique index associated with a particular service entry." ::= { g9983SvcEntry 1 } g9983SvcIfIdx OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "This is a unique index within the ifTable. It represents the interface index of a service to be transmitted over the G.Bond/TDIM service instance. This objects maps to the TR-159 attribute aServiceIfIndex." REFERENCE "[TR-159], Section 5.5.5.2" ::= { g9983SvcEntry 2 } g9983SvcType OBJECT-TYPE SYNTAX INTEGER { ds1(0), e1(1), nxds0(2), nxe0(3), ds3(4), e3(5), clock(6), ethernet(7), atm(8), gfpNoFCS(9), gfp(10) } MAX-ACCESS read-create STATUS current DESCRIPTION "G.Bond/TDIM service type. Possible values are: ds1 - Clear Channel DS1 (synchronous) e1 - Clear Channel E1 (synchronous) nxds0 - Fractional DS1 (synchronous) nxe0 - Fractional E1 (synchronous) ds3 - DS3 (synchronous) e3 - E3 (synchronous) clock - Clock transfer (synchronous) ethernet - Ethernet (asynchronous) atm - ATM (asynchronous) gfpNoFCS - GFP encapsulated without FCS (asynchronous) gfp - GFP encapsulated with FCS (asynchronous) For the GBS-R ports, the value of this object cannot be changed directly. This value may be changed as a result of a write operation on the g9983SvcType object of a remote GBS-C. Attempts to change this object MUST be rejected for the GBS-R ports. This object maps to the TR-159/G.998.3 attribute aServiceType." REFERENCE "[TR-159], Section 5.5.5.3; [G.998.3], Appendix II, C-II" ::= { g9983SvcEntry 3 } g9983SvcSize OBJECT-TYPE SYNTAX Unsigned32 (0|20..255) UNITS "octets" MAX-ACCESS read-create STATUS current DESCRIPTION "Service size, in octets, per bonding sub-block for a specific service identified by g9983SvcIdx. For TDM (synchronous) services with variable size (e.g., fractional DS1/E1), this object represents the number of DS0/E0 channels. For asynchronous services (Ethernet, ATM, GFPnoFCS, or GFP), this object represents the maximum number of octets. For non-fractional TDM services (i.e., DS1, E1, DS3, E3, and clock), the value of this object MUST be 0. A GET operation returns the current value. A SET operation, allowed on GBS-C ports, changes the service size to the indicated value. If the service type is a fixed-rate synchronous service (g9983SvcType is nxds0, nxe0, ds1, e1, ds3, e3, or clock), the operation MUST be rejected. This object maps to the TR-159/G.998.3 attribute aServiceSize." REFERENCE "[TR-159], Section 5.5.5.4; [G.998.3], Appendix II, C-III" ::= { g9983SvcEntry 4 } g9983SvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object controls the creation, modification, or deletion of the associated entry in the g9983SvcTable per the semantics of RowStatus. If an 'active' entry is referenced via g9983OperSvcIdx or a g9983PortConfAdminServices instance, or indexes a g9983SvcPm*Entry, the entry MUST remain 'active'. An 'active' entry SHALL NOT be modified. In order to modify an existing entry, it MUST be taken out of service (by setting this object to 'notInService'), modified, and set to 'active' again." ::= { g9983SvcEntry 5 } ------------------------------- -- Performance Monitoring group ------------------------------- g9983PM OBJECT IDENTIFIER ::= { g9983Port 6 } g9983PortPmCurTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983PortPmCurEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains current Performance Monitoring information for a G.Bond/TDIM port. This table contains live data from the equipment and as such is NOT persistent." ::= { g9983PM 1 } g9983PortPmCurEntry OBJECT-TYPE SYNTAX G9983PortPmCurEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Port PM table. Each entry represents a G.Bond/TDIM port indexed by the ifIndex." INDEX { ifIndex } ::= { g9983PortPmCurTable 1 } G9983PortPmCurEntry ::= SEQUENCE { g9983PortPmCur15MinValidIntervals HCPerfValidIntervals, g9983PortPmCur15MinInvalidIntervals HCPerfInvalidIntervals, g9983PortPmCur15MinTimeElapsed HCPerfTimeElapsed, g9983PortPmCur15MinCrc4s HCPerfCurrentCount, g9983PortPmCur15MinCrc6s HCPerfCurrentCount, g9983PortPmCur15MinCrc8s HCPerfCurrentCount, g9983PortPmCur1DayValidIntervals Unsigned32, g9983PortPmCur1DayInvalidIntervals Unsigned32, g9983PortPmCur1DayTimeElapsed HCPerfTimeElapsed, g9983PortPmCur1DayCrc4s HCPerfCurrentCount, g9983PortPmCur1DayCrc6s HCPerfCurrentCount, g9983PortPmCur1DayCrc8s HCPerfCurrentCount } g9983PortPmCur15MinValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 15-minute intervals for which the performance data was collected. The value of this object will be 96 or the maximum number of 15-minute history intervals collected by the implementation, unless the measurement was (re)started recently, in which case the value will be the number of complete 15-minute intervals for which there are at least some data. In certain cases, it is possible that some intervals are unavailable. In this case, this object reports the maximum interval number for which data is available. This object partially maps to the TR-159 attribute aGroupPerf15MinValidIntervals." REFERENCE "[TR-159], Section 5.5.1.32" ::= { g9983PortPmCurEntry 1 } g9983PortPmCur15MinInvalidIntervals OBJECT-TYPE SYNTAX HCPerfInvalidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 15-minute intervals for which the performance data was not always available. The value will typically be zero, except in cases where the data for some intervals are not available. This object partially maps to the TR-159 attribute aGroupPerf15MinInvalidIntervals." REFERENCE "[TR-159], Section 5.5.1.33" ::= { g9983PortPmCurEntry 2 } g9983PortPmCur15MinTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds that have elapsed since the beginning of the current 15-minute performance interval. This object partially maps to the TR-159 attribute aGroupPerfCurr15MinTimeElapsed." REFERENCE "[TR-159], Section 5.5.1.34" ::= { g9983PortPmCurEntry 3 } g9983PortPmCur15MinCrc4s OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-4 errors (frame header errors) on all active pairs in the G.Bond/TDIM port during the current 15-minute performance interval. Simultaneous errors on M lines SHOULD be counted M times. Note that the total number of CRC-4 errors is indicated by the g9983PortStatCrc4Errors object. This object is inhibited during Severely Errored Seconds (SES) or Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.4.1" ::= { g9983PortPmCurEntry 4} g9983PortPmCur15MinCrc6s OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-6 errors (super-frame errors) on all active pairs in the G.Bond/TDIM port during the current 15-minute performance interval. Simultaneous errors on M lines SHOULD be counted 1 time. Note that the total number of CRC-6 errors is indicated by the g9983PortStatCrc6Errors object. This object is inhibited during Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.4.2" ::= { g9983PortPmCurEntry 5} g9983PortPmCur15MinCrc8s OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-8 errors (event/message errors) on all active pairs in the G.Bond/TDIM port during the current 15-minute performance interval. Simultaneous errors on M lines SHOULD be counted M times. Note that the total number of CRC-8 errors is indicated by the g9983PortStatCrc8Errors object. This object is inhibited during Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.4.3" ::= { g9983PortPmCurEntry 6} g9983PortPmCur1DayValidIntervals OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 1-day intervals for which data was collected. The value of this object will be 7 or the maximum number of 1-day history intervals collected by the implementation, unless the measurement was (re)started recently, in which case the value will be the number of complete 1-day intervals for which there are at least some data. In certain cases, it is possible that some intervals are unavailable. In this case, this object reports the maximum interval number for which data is available." REFERENCE "[TR-159], Section 5.5.1.45" ::= { g9983PortPmCurEntry 7 } g9983PortPmCur1DayInvalidIntervals OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 1-day intervals for which data was not always available. The value will typically be zero, except in cases where the data for some intervals are not available." REFERENCE "[TR-159], Section 5.5.1.46" ::= { g9983PortPmCurEntry 8 } g9983PortPmCur1DayTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds that have elapsed since the beginning of the current 1-day performance interval." REFERENCE "[TR-159], Section 5.5.1.47" ::= { g9983PortPmCurEntry 9 } g9983PortPmCur1DayCrc4s OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-4 errors on the G.Bond/TDIM port in the current 1-day performance interval. This object is inhibited during Severely Errored Seconds (SES) and Unavailable Seconds (UAS)." ::= { g9983PortPmCurEntry 10 } g9983PortPmCur1DayCrc6s OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-6 errors on the G.Bond/TDIM port in the current 1-day performance interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9983PortPmCurEntry 11 } g9983PortPmCur1DayCrc8s OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-8 errors on the G.Bond/TDIM port in the current 1-day performance interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9983PortPmCurEntry 12 } -- Port PM history: 15-min buckets g9983PortPm15MinTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983PortPm15MinEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains historical 15-minute buckets of Performance Monitoring information for a G.Bond/TDIM port (a row for each 15-minute interval, up to 96 intervals). Entries in this table MUST be maintained in a persistent manner." ::= { g9983PM 2 } g9983PortPm15MinEntry OBJECT-TYPE SYNTAX G9983PortPm15MinEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Port historical 15-minute PM table. Each entry represents Performance Monitoring data for a G.Bond TDIM port, indexed by the ifIndex, collected during a particular 15-minute interval, indexed by the g9983PortPm15MinIntervalIndex." INDEX { ifIndex, g9983PortPm15MinIntervalIndex } ::= { g9983PortPm15MinTable 1 } G9983PortPm15MinEntry ::= SEQUENCE { g9983PortPm15MinIntervalIndex Unsigned32, g9983PortPm15MinIntervalMoniTime HCPerfTimeElapsed, g9983PortPm15MinIntervalCrc4s HCPerfIntervalCount, g9983PortPm15MinIntervalCrc6s HCPerfIntervalCount, g9983PortPm15MinIntervalCrc8s HCPerfIntervalCount, g9983PortPm15MinIntervalValid TruthValue } g9983PortPm15MinIntervalIndex OBJECT-TYPE SYNTAX Unsigned32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance data interval number. 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are OPTIONAL. This object partially maps to the TR-159 attribute aGroupPerf15MinIntervalNumber." REFERENCE "[TR-159], Section 5.5.1.57" ::= { g9983PortPm15MinEntry 1 } g9983PortPm15MinIntervalMoniTime OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds over which the performance data was actually monitored. This value will be the same as the interval duration (900 seconds), except in a situation where performance data could not be collected for any reason." ::= { g9983PortPm15MinEntry 2 } g9983PortPm15MinIntervalCrc4s OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-4 errors on the G.Bond/TDIM port during the 15-minute performance history interval. This object is inhibited during Severely Errored Seconds (SES) and Unavailable Seconds (UAS)." ::= { g9983PortPm15MinEntry 3 } g9983PortPm15MinIntervalCrc6s OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-6 errors on the G.Bond/TDIM port during the 15-minute performance history interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9983PortPm15MinEntry 4 } g9983PortPm15MinIntervalCrc8s OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-8 errors on the G.Bond/TDIM port during the current 15-minute performance interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9983PortPm15MinEntry 5 } g9983PortPm15MinIntervalValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only object indicating whether or not this history bucket contains valid data. A valid bucket is reported as true(1) and an invalid bucket as false(2). If this history bucket is invalid, the BTU-C MUST NOT produce notifications based upon the value of the counters in this bucket. Note that an implementation may decide not to store invalid history buckets in its database. In such a case, this object is not required, as only valid history buckets are available while invalid history buckets are simply not in the database. This object partially maps to the TR-159 attribute aGroupPerf15MinIntervalValid." REFERENCE "[TR-159], Section 5.5.1.58" ::= { g9983PortPm15MinEntry 6 } -- Port PM history: 1-day buckets g9983PortPm1DayTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983PortPm1DayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains historical 1-day buckets of Performance Monitoring information for a G.Bond/TDIM port (a row for each 1-day interval, up to 7 intervals). Entries in this table MUST be maintained in a persistent manner." ::= { g9983PM 3 } g9983PortPm1DayEntry OBJECT-TYPE SYNTAX G9983PortPm1DayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Port historical 1-day PM table. Each entry represents Performance Monitoring data for such a port, indexed by the ifIndex, collected during a particular 1-day interval, indexed by the g9983PortPm1DayIntervalIndex." INDEX { ifIndex, g9983PortPm1DayIntervalIndex } ::= { g9983PortPm1DayTable 1 } G9983PortPm1DayEntry ::= SEQUENCE { g9983PortPm1DayIntervalIndex Unsigned32, g9983PortPm1DayIntervalMoniTime HCPerfTimeElapsed, g9983PortPm1DayIntervalCrc4s HCPerfIntervalCount, g9983PortPm1DayIntervalCrc6s HCPerfIntervalCount, g9983PortPm1DayIntervalCrc8s HCPerfIntervalCount, g9983PortPm1DayIntervalValid TruthValue } g9983PortPm1DayIntervalIndex OBJECT-TYPE SYNTAX Unsigned32 (1..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance data interval number. 1 is the most recent previous interval; interval 7 is 7 days ago. Intervals 2..7 are OPTIONAL. This object partially maps to the TR-159 attribute aGroupPerf1DayIntervalNumber." REFERENCE "[TR-159], Section 5.5.1.62" ::= { g9983PortPm1DayEntry 1 } g9983PortPm1DayIntervalMoniTime OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds over which the performance data was actually monitored. This value will be the same as the interval duration (86400 seconds), except in a situation where performance data could not be collected for any reason. This object partially maps to the TR-159 attribute aGroupPerf1DayIntervalMoniSecs." REFERENCE "[TR-159], Section 5.5.1.64" ::= { g9983PortPm1DayEntry 2 } g9983PortPm1DayIntervalCrc4s OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-4 errors on the G.Bond/TDIM port during the 1-day performance history interval. This object is inhibited during Severely Errored Seconds (SES) and Unavailable Seconds (UAS)." ::= { g9983PortPm1DayEntry 3 } g9983PortPm1DayIntervalCrc6s OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-6 errors on the G.Bond/TDIM port during the 1-day performance history interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9983PortPm1DayEntry 4 } g9983PortPm1DayIntervalCrc8s OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of CRC-8 errors on the G.Bond/TDIM port during the current 1-day performance interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9983PortPm1DayEntry 5 } g9983PortPm1DayIntervalValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only object indicating whether or not this history bucket contains valid data. A valid bucket is reported as true(1) and an invalid bucket as false(2). If this history bucket is invalid, the BTU-C MUST NOT produce notifications based upon the value of the counters in this bucket. Note that an implementation may decide not to store invalid history buckets in its database. In such a case, this object is not required, as only valid history buckets are available while invalid history buckets are simply not in the database. This object partially maps to the TR-159 attribute aGroupPerf1DayIntervalValid." REFERENCE "[TR-159], Section 5.5.1.63" ::= { g9983PortPm1DayEntry 6 } -- Services PM g9983SvcPmCurTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983SvcPmCurEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains current Performance Monitoring information for the services of a G.Bond/TDIM port. This table contains live data from the equipment and as such is NOT persistent." ::= { g9983PM 4 } g9983SvcPmCurEntry OBJECT-TYPE SYNTAX G9983SvcPmCurEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Services PM table. Each entry represents a service, indexed by the g9983SvcIdx, in a G.Bond/TDIM port, indexed by the ifIndex." INDEX { ifIndex, g9983SvcIdx } ::= { g9983SvcPmCurTable 1 } G9983SvcPmCurEntry ::= SEQUENCE { g9983SvcPmCur15MinValidIntervals HCPerfValidIntervals, g9983SvcPmCur15MinInvalidIntervals HCPerfInvalidIntervals, g9983SvcPmCur15MinTimeElapsed HCPerfTimeElapsed, g9983SvcPmCur15MinDowns HCPerfCurrentCount, g9983SvcPmCur1DayValidIntervals Unsigned32, g9983SvcPmCur1DayInvalidIntervals Unsigned32, g9983SvcPmCur1DayTimeElapsed HCPerfTimeElapsed, g9983SvcPmCur1DayDowns HCPerfCurrentCount } g9983SvcPmCur15MinValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 15-minute intervals for which the performance data was collected. The value of this object will be 96 or the maximum number of 15-minute history intervals collected by the implementation, unless the measurement was (re)started recently, in which case the value will be the number of complete 15-minute intervals for which there are at least some data. In certain cases, it is possible that some intervals are unavailable. In this case, this object reports the maximum interval number for which data is available. This object partially maps to the TR-159 attribute aGroupPerf15MinValidIntervals." REFERENCE "[TR-159], Section 5.5.1.32" ::= { g9983SvcPmCurEntry 1 } g9983SvcPmCur15MinInvalidIntervals OBJECT-TYPE SYNTAX HCPerfInvalidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 15-minute intervals for which the performance data was not always available. The value will typically be zero, except in cases where the data for some intervals are not available. This object partially maps to the TR-159 attribute aGroupPerf15MinInvalidIntervals." REFERENCE "[TR-159], Section 5.5.1.33" ::= { g9983SvcPmCurEntry 2 } g9983SvcPmCur15MinTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds that have elapsed since the beginning of the current 15-minute performance interval. This object partially maps to the TR-159 attribute aGroupPerfCurr15MinTimeElapsed." REFERENCE "[TR-159], Section 5.5.1.34" ::= { g9983SvcPmCurEntry 3 } g9983SvcPmCur15MinDowns OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds in the current 15-minute performance interval during which a particular TDIM service was 'down', as indicated by the g9983OperSvcState object. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9983SvcPmCurEntry 4} g9983SvcPmCur1DayValidIntervals OBJECT-TYPE SYNTAX Unsigned32 (0..7) UNITS "days" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 1-day performance history intervals for which the data was collected. The value of this object will be 7 or the maximum number of 1-day history intervals collected by the implementation, unless the measurement was (re)started recently, in which case the value will be the number of complete 1-day intervals for which there are at least some data. In certain cases, it is possible that some intervals are unavailable. In this case, this object reports the maximum interval number for which data is available." REFERENCE "[TR-159], Section 5.5.1.45" ::= { g9983SvcPmCurEntry 5 } g9983SvcPmCur1DayInvalidIntervals OBJECT-TYPE SYNTAX Unsigned32 (0..7) UNITS "days" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 1-day performance history intervals for which the performance data was not always available. The value will typically be zero, except in cases where the data for some intervals are not available." REFERENCE "[TR-159], Section 5.5.1.46" ::= { g9983SvcPmCurEntry 6 } g9983SvcPmCur1DayTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds that have elapsed since the beginning of the current 1-day performance interval." REFERENCE "[TR-159], Section 5.5.1.47" ::= { g9983SvcPmCurEntry 7 } g9983SvcPmCur1DayDowns OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds in the current 1-day performance interval during which a particular TDIM service was 'down', as indicated by the g9983OperSvcState object. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9983SvcPmCurEntry 8 } -- Service PM history: 15-min buckets g9983SvcPm15MinTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983SvcPm15MinEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains historical 15-minute buckets of Performance Monitoring information for the services of a G.Bond/TDIM port (a multi-dimensional row for each 15-minute interval, up to 96 intervals). Entries in this table MUST be maintained in a persistent manner." ::= { g9983PM 5 } g9983SvcPm15MinEntry OBJECT-TYPE SYNTAX G9983SvcPm15MinEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Service historical 15-minute PM table. Each entry represents Performance Monitoring data for a particular service, indexed by the g9983SvcIdx, in a G.Bond TDIM port, indexed by the ifIndex, collected during a particular 15-minute interval, indexed by the g9983SvcPm15MinIntervalIndex." INDEX { ifIndex, g9983SvcIdx, g9983SvcPm15MinIntervalIndex } ::= { g9983SvcPm15MinTable 1 } G9983SvcPm15MinEntry ::= SEQUENCE { g9983SvcPm15MinIntervalIndex Unsigned32, g9983SvcPm15MinIntervalMoniTime HCPerfTimeElapsed, g9983SvcPm15MinIntervalDowns HCPerfIntervalCount, g9983SvcPm15MinIntervalValid TruthValue } g9983SvcPm15MinIntervalIndex OBJECT-TYPE SYNTAX Unsigned32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance data interval number. 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are OPTIONAL. This object partially maps to the TR-159 attribute aGroupPerf15MinIntervalNumber." REFERENCE "[TR-159], Section 5.5.1.57" ::= { g9983SvcPm15MinEntry 1 } g9983SvcPm15MinIntervalMoniTime OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds over which the performance data was actually monitored. This value will be the same as the interval duration (900 seconds), except in a situation where performance data could not be collected for any reason." ::= { g9983SvcPm15MinEntry 2 } g9983SvcPm15MinIntervalDowns OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds in the 15-minute performance history interval during which a particular TDIM service was 'down', as indicated by the g9983OperSvcState object. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9983SvcPm15MinEntry 3 } g9983SvcPm15MinIntervalValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only object indicating whether or not this history bucket contains valid data. A valid bucket is reported as true(1) and an invalid bucket as false(2). If this history bucket is invalid, the BTU-C MUST NOT produce notifications based upon the value of the counters in this bucket. Note that an implementation may decide not to store invalid history buckets in its database. In such a case, this object is not required, as only valid history buckets are available while invalid history buckets are simply not in the database. This object partially maps to the TR-159 attribute aGroupPerf15MinIntervalValid." REFERENCE "[TR-159], Section 5.5.1.58" ::= { g9983SvcPm15MinEntry 4 } -- Service PM history: 1-day buckets g9983SvcPm1DayTable OBJECT-TYPE SYNTAX SEQUENCE OF G9983SvcPm1DayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains historical 1-day buckets of Performance Monitoring information for the services of a G.Bond/TDIM port (a multi-dimensional row for each 1-day interval, up to 7 intervals). Entries in this table MUST be maintained in a persistent manner." ::= { g9983PM 6 } g9983SvcPm1DayEntry OBJECT-TYPE SYNTAX G9983SvcPm1DayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/TDIM Service historical 1-day PM table. Each entry represents Performance Monitoring data for a particular service, indexed by the g9983SvcIdx, defined in a G.Bond/TDIM port, indexed by the ifIndex, collected during a particular 1-day interval, indexed by the g9983SvcPm1DayIntervalIndex." INDEX { ifIndex, g9983SvcIdx, g9983SvcPm1DayIntervalIndex } ::= { g9983SvcPm1DayTable 1 } G9983SvcPm1DayEntry ::= SEQUENCE { g9983SvcPm1DayIntervalIndex Unsigned32, g9983SvcPm1DayIntervalMoniTime HCPerfTimeElapsed, g9983SvcPm1DayIntervalDowns HCPerfIntervalCount, g9983SvcPm1DayIntervalValid TruthValue } g9983SvcPm1DayIntervalIndex OBJECT-TYPE SYNTAX Unsigned32 (1..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance data interval number. 1 is the most recent previous interval; interval 7 is 7 days ago. Intervals 2..7 are OPTIONAL. This object partially maps to the TR-159 attribute aGroupPerf1DayIntervalNumber." REFERENCE "[TR-159], Section 5.5.1.62" ::= { g9983SvcPm1DayEntry 1 } g9983SvcPm1DayIntervalMoniTime OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds over which the performance data was actually monitored. This value will be the same as the interval duration (86400 seconds), except in a situation where performance data could not be collected for any reason. This object partially maps to the TR-159 attribute aGroupPerf1DayIntervalMoniSecs." REFERENCE "[TR-159], Section 5.5.1.64" ::= { g9983SvcPm1DayEntry 2 } g9983SvcPm1DayIntervalDowns OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds in the 1-day performance history interval during which a particular TDIM service was 'down', as indicated by the g9983OperSvcState object. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9983SvcPm1DayEntry 3 } g9983SvcPm1DayIntervalValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only object indicating whether or not this history bucket contains valid data. A valid bucket is reported as true(1) and an invalid bucket as false(2). If this history bucket is invalid, the BTU-C MUST NOT produce notifications based upon the value of the counters in this bucket. Note that an implementation may decide not to store invalid history buckets in its database. In such a case, this object is not required, as only valid history buckets are available while invalid history buckets are simply not in the database. This object partially maps to the TR-159 attribute aGroupPerf1DayIntervalValid." REFERENCE "[TR-159], Section 5.5.1.63" ::= { g9983SvcPm1DayEntry 4 } -- -- Conformance Statements -- g9983Groups OBJECT IDENTIFIER ::= { g9983Conformance 1 } g9983Compliances OBJECT IDENTIFIER ::= { g9983Conformance 2 } -- Object Groups g9983BasicGroup OBJECT-GROUP OBJECTS { g9983PortConfAdminServices, g9983PortStatCrc4Errors, g9983PortStatCrc6Errors, g9983PortStatCrc8Errors, g9983PortCapFecSupported, g9983OperSvcIdx, g9983OperSvcState, g9983SvcIfIdx, g9983SvcType, g9983SvcSize, g9983SvcRowStatus, g9983PortStatFltStatus } STATUS current DESCRIPTION "A collection of objects representing management information for G.Bond/TDIM ports." ::= { g9983Groups 1 } g9983FecGroup OBJECT-GROUP OBJECTS { g9983PortCapFecSupported, g9983PortConfFecAdminState, g9983PortStatFecOperState, g9983PortConfFecWordSize, g9983PortConfFecRedundancySize, g9983PortConfFecInterleaverType, g9983PortConfFecInterleaverDepth, g9983PortCapFecMaxWordSize, g9983PortCapFecMaxRedundancySize, g9983PortCapFecInterleaverTypeSupported, g9983PortCapFecMaxInterleaverDepth } STATUS current DESCRIPTION "A collection of objects supporting the OPTIONAL Forward Error Correction (FEC) and Interleaver function in G.Bond/TDIM ports." ::= { g9983Groups 2 } g9983AlarmConfGroup OBJECT-GROUP OBJECTS { g9983PortConfSvcUpDownEnable } STATUS current DESCRIPTION "A collection of objects required for configuration of alarm thresholds and notifications in G.Bond/TDIM ports." ::= { g9983Groups 3 } g9983NotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { g9983SvcUp, g9983SvcDown } STATUS current DESCRIPTION "This group supports notifications of significant conditions associated with G.Bond/TDIM ports." ::= { g9983Groups 4 } g9983PerfCurrGroup OBJECT-GROUP OBJECTS { g9983PortPmCur15MinValidIntervals, g9983PortPmCur15MinInvalidIntervals, g9983PortPmCur15MinTimeElapsed, g9983PortPmCur15MinCrc4s, g9983PortPmCur15MinCrc6s, g9983PortPmCur15MinCrc8s, g9983PortPmCur1DayValidIntervals, g9983PortPmCur1DayInvalidIntervals, g9983PortPmCur1DayTimeElapsed, g9983PortPmCur1DayCrc4s, g9983PortPmCur1DayCrc6s, g9983PortPmCur1DayCrc8s, g9983SvcPmCur15MinValidIntervals, g9983SvcPmCur15MinInvalidIntervals, g9983SvcPmCur15MinTimeElapsed, g9983SvcPmCur15MinDowns, g9983SvcPmCur1DayValidIntervals, g9983SvcPmCur1DayInvalidIntervals, g9983SvcPmCur1DayTimeElapsed, g9983SvcPmCur1DayDowns } STATUS current DESCRIPTION "A collection of objects supporting OPTIONAL current Performance Monitoring information for G.Bond/TDIM ports." ::= { g9983Groups 5 } g9983Perf15MinGroup OBJECT-GROUP OBJECTS { g9983PortPm15MinIntervalMoniTime, g9983PortPm15MinIntervalCrc4s, g9983PortPm15MinIntervalCrc6s, g9983PortPm15MinIntervalCrc8s, g9983PortPm15MinIntervalValid, g9983SvcPm15MinIntervalMoniTime, g9983SvcPm15MinIntervalDowns, g9983SvcPm15MinIntervalValid } STATUS current DESCRIPTION "A collection of objects supporting OPTIONAL historical Performance Monitoring information for G.Bond/TDIM ports, during previous 15-minute intervals." ::= { g9983Groups 6 } g9983Perf1DayGroup OBJECT-GROUP OBJECTS { g9983PortPm1DayIntervalMoniTime, g9983PortPm1DayIntervalCrc4s, g9983PortPm1DayIntervalCrc6s, g9983PortPm1DayIntervalCrc8s, g9983PortPm1DayIntervalValid, g9983SvcPm1DayIntervalMoniTime, g9983SvcPm1DayIntervalDowns, g9983SvcPm1DayIntervalValid } STATUS current DESCRIPTION "A collection of objects supporting OPTIONAL historical Performance Monitoring information for G.Bond/TDIM ports, during previous 1-day intervals." ::= { g9983Groups 7 } -- Compliance Statements g9983Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for G.Bond/TDIM interfaces. Compliance with the following external compliance statements is REQUIRED: MIB Module Compliance Statement ---------- -------------------- IF-MIB ifCompliance3 GBOND-MIB gBondCompliance" MODULE -- this module MANDATORY-GROUPS { g9983BasicGroup, g9983AlarmConfGroup, g9983NotificationGroup } GROUP g9983FecGroup DESCRIPTION "Support for this group is only required for implementations supporting the G.Bond/TDIM FEC and Interleaver function." GROUP g9983PerfCurrGroup DESCRIPTION "Support for this group is only required for implementations supporting Performance Monitoring." GROUP g9983Perf15MinGroup DESCRIPTION "Support for this group is only required for implementations supporting historical Performance Monitoring." GROUP g9983Perf1DayGroup DESCRIPTION "Support for this group is only required for implementations supporting historical Performance Monitoring." ::= { g9983Compliances 1 } END