MPLS-LC-ATM-STD-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF RowStatus, StorageType, TruthValue FROM SNMPv2-TC AtmVpIdentifier FROM ATM-TC-MIB mplsStdMIB, MplsAtmVcIdentifier FROM MPLS-TC-STD-MIB mplsInterfaceIndex FROM MPLS-LSR-STD-MIB ; mplsLcAtmStdMIB MODULE-IDENTITY LAST-UPDATED "200601120000Z" -- 12 January 2006 ORGANIZATION "Multiprotocol Label Switching (MPLS) Working Group" CONTACT-INFO " Thomas D. Nadeau Postal: Cisco Systems, Inc. 250 Apollo Drive Chelmsford, MA 01824 Tel: +1-978-244-3051 Email: [email protected] Subrahmanya Hegde Postal: Cisco Systems, Inc. 225 East Tazman Drive Tel: +1-408-525-6562 Email: [email protected] General comments should be sent to [email protected] " DESCRIPTION "This MIB module contains managed object definitions for MPLS Label-Controlled ATM interfaces as defined in [RFC3035]. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4368; see the RFC itself for full legal notices." -- Revision history. REVISION "200601120000Z" -- 12 January 2006 DESCRIPTION "Initial revision, published as part of RFC 4368." ::= { mplsStdMIB 9 } -- Top level components of this MIB module. -- Tables, Scalars, Notifications, Conformance mplsLcAtmStdNotifications OBJECT IDENTIFIER ::= { mplsLcAtmStdMIB 0 } mplsLcAtmStdObjects OBJECT IDENTIFIER ::= { mplsLcAtmStdMIB 1 } mplsLcAtmStdConformance OBJECT IDENTIFIER ::= { mplsLcAtmStdMIB 2 } -- MPLS LC-ATM Interface Configuration Table. mplsLcAtmStdInterfaceConfTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLcAtmStdInterfaceConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies per-interface MPLS LC-ATM capability and associated information. In particular, this table sparsely extends the MPLS-LSR-STD-MIB's mplsInterfaceConfTable." ::= { mplsLcAtmStdObjects 1 } mplsLcAtmStdInterfaceConfEntry OBJECT-TYPE SYNTAX MplsLcAtmStdInterfaceConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by an LSR for every interface capable of supporting MPLS LC-ATM. Each entry in this table will exist only if a corresponding entry in ifTable and mplsInterfaceConfTable exists. If the associated entries in ifTable and mplsInterfaceConfTable are deleted, the corresponding entry in this table must also be deleted shortly thereafter." INDEX { mplsInterfaceIndex } ::= { mplsLcAtmStdInterfaceConfTable 1 } MplsLcAtmStdInterfaceConfEntry ::= SEQUENCE { mplsLcAtmStdCtrlVpi AtmVpIdentifier, mplsLcAtmStdCtrlVci MplsAtmVcIdentifier, mplsLcAtmStdUnlabTrafVpi AtmVpIdentifier, mplsLcAtmStdUnlabTrafVci MplsAtmVcIdentifier, mplsLcAtmStdVcMerge TruthValue, mplsLcAtmVcDirectlyConnected TruthValue, mplsLcAtmLcAtmVPI AtmVpIdentifier, mplsLcAtmStdIfConfRowStatus RowStatus, mplsLcAtmStdIfConfStorageType StorageType } mplsLcAtmStdCtrlVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "This is the VPI value over which this LSR is willing to accept control traffic on this interface." ::= { mplsLcAtmStdInterfaceConfEntry 1 } mplsLcAtmStdCtrlVci OBJECT-TYPE SYNTAX MplsAtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "This is the VCI value over which this LSR is willing to accept control traffic on this interface." ::= { mplsLcAtmStdInterfaceConfEntry 2 } mplsLcAtmStdUnlabTrafVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "This is the VPI value over which this LSR is willing to accept unlabeled traffic on this interface." ::= { mplsLcAtmStdInterfaceConfEntry 3 } mplsLcAtmStdUnlabTrafVci OBJECT-TYPE SYNTAX MplsAtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "This is the VCI value over which this LSR is willing to accept unlabeled traffic on this interface." ::= { mplsLcAtmStdInterfaceConfEntry 4 } mplsLcAtmStdVcMerge OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If set to true(1), indicates that this interface is capable of ATM VC merge; otherwise, it MUST be set to false(2)." DEFVAL { false } ::= { mplsLcAtmStdInterfaceConfEntry 5 } mplsLcAtmVcDirectlyConnected OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This value indicates whether an LC-ATM is directly or indirectly (by means of a VP) connected. If set to true(1), indicates that this interface is directly connected LC-ATM; otherwise, it MUST be set to false(2). Note that although it can be intimated from RFC 3057 that multiple VPs may be used, in practice only a single one is used, and therefore the authors of this MIB module have chosen to model it as such." DEFVAL { true } ::= { mplsLcAtmStdInterfaceConfEntry 6 } mplsLcAtmLcAtmVPI OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "This is the VPI value used for indirectly connected LC-ATM interfaces. For these interfaces, the VPI field is not available to MPLS, and the label MUST be encoded entirely within the VCI field (see [RFC3035]). If the interface is directly connected, this value MUST be set to zero." DEFVAL { 0 } ::= { mplsLcAtmStdInterfaceConfEntry 7 } mplsLcAtmStdIfConfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create and delete entries in this table. When configuring entries in this table, the corresponding ifEntry and mplsInterfaceConfEntry MUST exist beforehand. If a manager attempts to create an entry for a corresponding mplsInterfaceConfEntry that does not support LC-ATM, the agent MUST return an inconsistentValue error. If this table is implemented read-only, then the agent must set this object to active(1) when this row is made active. If this table is implemented writable, then an agent MUST not allow modification to its objects once this value is set to active(1), except to mplsLcAtmStdIfConfRowStatus and mplsLcAtmStdIfConfStorageType." ::= { mplsLcAtmStdInterfaceConfEntry 8 } mplsLcAtmStdIfConfStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { mplsLcAtmStdInterfaceConfEntry 9 } -- End of mplsLcAtmStdInterfaceConfTable -- Module compliance. mplsLcAtmStdCompliances OBJECT IDENTIFIER ::= { mplsLcAtmStdConformance 1 } mplsLcAtmStdGroups OBJECT IDENTIFIER ::= { mplsLcAtmStdConformance 2 } -- Compliance requirement for full compliance mplsLcAtmStdModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents that provide full support for MPLS-LC-ATM-STD-MIB. Such devices can be monitored and also be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { mplsLcAtmStdIfGroup } OBJECT mplsLcAtmStdIfConfRowStatus SYNTAX RowStatus { active(1), notInService(2) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notReady is not required." ::= { mplsLcAtmStdCompliances 1 } -- Compliance requirement for read-only implementations. mplsLcAtmStdModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance requirement for implementations that only provide read-only support for MPLS-LC-ATM-STD-MIB. Such devices can be monitored but cannot be configured using this MIB module. " MODULE -- this module MANDATORY-GROUPS { mplsLcAtmStdIfGroup } -- mplsLcAtmStdInterfaceConfTable OBJECT mplsLcAtmStdCtrlVpi MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLcAtmStdCtrlVci MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLcAtmStdUnlabTrafVpi MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLcAtmStdUnlabTrafVci MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLcAtmStdVcMerge MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLcAtmStdIfConfRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLcAtmVcDirectlyConnected MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLcAtmLcAtmVPI MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLcAtmStdIfConfStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { mplsLcAtmStdCompliances 2 } -- Units of conformance. mplsLcAtmStdIfGroup OBJECT-GROUP OBJECTS { mplsLcAtmStdCtrlVpi, mplsLcAtmStdCtrlVci, mplsLcAtmStdUnlabTrafVpi, mplsLcAtmStdUnlabTrafVci, mplsLcAtmStdVcMerge, mplsLcAtmVcDirectlyConnected, mplsLcAtmLcAtmVPI, mplsLcAtmStdIfConfRowStatus, mplsLcAtmStdIfConfStorageType } STATUS current DESCRIPTION "Collection of objects needed for MPLS LC-ATM interface configuration." ::= { mplsLcAtmStdGroups 1 } END