MPLS-LDP-STD-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE, Integer32, Counter32, Unsigned32 FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] RowStatus, TimeInterval, TruthValue, TimeStamp, StorageType FROM SNMPv2-TC -- [RFC2579] InetAddressPrefixLength, InetAddressType, InetAddress, InetPortNumber FROM INET-ADDRESS-MIB -- [RFC3291] IndexInteger, IndexIntegerNextFree FROM DIFFSERV-MIB -- [RFC3289] mplsStdMIB, MplsLabelDistributionMethod, MplsLdpIdentifier, MplsLdpLabelType, MplsLspType, MplsLsrIdentifier, MplsRetentionMode FROM MPLS-TC-STD-MIB -- [RFC3811] MplsIndexType FROM MPLS-LSR-STD-MIB; -- [RFC3813] mplsLdpStdMIB MODULE-IDENTITY LAST-UPDATED "200406030000Z" -- June 3, 2004 ORGANIZATION "Multiprotocol Label Switching (mpls) Working Group" CONTACT-INFO "Joan Cucchiara ([email protected]) Marconi Communications, Inc. Hans Sjostrand ([email protected]) ipUnplugged James V. Luciani ([email protected]) Marconi Communications, Inc. Working Group Chairs: George Swallow, email: [email protected] Loa Andersson, email: [email protected] MPLS Working Group, email: [email protected]" DESCRIPTION "Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3815. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB contains managed object definitions for the 'Multiprotocol Label Switching, Label Distribution Protocol, LDP' document." REVISION "200406030000Z" -- June 3, 2004 DESCRIPTION "Initial version published as part of RFC 3815." ::= { mplsStdMIB 4 } --**************************************************************** mplsLdpNotifications OBJECT IDENTIFIER ::= { mplsLdpStdMIB 0 } mplsLdpObjects OBJECT IDENTIFIER ::= { mplsLdpStdMIB 1 } mplsLdpConformance OBJECT IDENTIFIER ::= { mplsLdpStdMIB 2 } --**************************************************************** -- MPLS LDP Objects --**************************************************************** mplsLdpLsrObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 1 } mplsLdpEntityObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 2 } -- -- The MPLS Label Distribution Protocol's -- Label Switching Router Objects -- mplsLdpLsrId OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The Label Switching Router's Identifier." ::= { mplsLdpLsrObjects 1 } mplsLdpLsrLoopDetectionCapable OBJECT-TYPE SYNTAX INTEGER { none(1), other(2), hopCount(3), pathVector(4), hopCountAndPathVector(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "A indication of whether this Label Switching Router supports loop detection. none(1) -- Loop Detection is not supported on this LSR. other(2) -- Loop Detection is supported but by a method other than those listed below. hopCount(3) -- Loop Detection is supported by Hop Count only. pathVector(4) -- Loop Detection is supported by Path Vector only. hopCountAndPathVector(5) -- Loop Detection is supported by both Hop Count And Path Vector. Since Loop Detection is determined during Session Initialization, an individual session may not be running with loop detection. This object simply gives an indication of whether or not the LSR has the ability to support Loop Detection and which types." ::= { mplsLdpLsrObjects 2 } -- -- The MPLS Label Distribution Protocol Entity Objects -- mplsLdpEntityLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the most recent addition or deletion of an entry to/from the mplsLdpEntityTable/mplsLdpEntityStatsTable, or the most recent change in value of any objects in the mplsLdpEntityTable. If no such changes have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value." ::= { mplsLdpEntityObjects 1 } mplsLdpEntityIndexNext OBJECT-TYPE SYNTAX IndexIntegerNextFree MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for mplsLdpEntityIndex when creating entries in the mplsLdpEntityTable. The value 0 indicates that no unassigned entries are available." ::= { mplsLdpEntityObjects 2 } mplsLdpEntityTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the MPLS Label Distribution Protocol Entities which exist on this Label Switching Router (LSR) or Label Edge Router (LER)." ::= { mplsLdpEntityObjects 3 } mplsLdpEntityEntry OBJECT-TYPE SYNTAX MplsLdpEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents an LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex } ::= { mplsLdpEntityTable 1 } MplsLdpEntityEntry ::= SEQUENCE { mplsLdpEntityLdpId MplsLdpIdentifier, mplsLdpEntityIndex IndexInteger, mplsLdpEntityProtocolVersion Unsigned32, mplsLdpEntityAdminStatus INTEGER, mplsLdpEntityOperStatus INTEGER, mplsLdpEntityTcpPort InetPortNumber, mplsLdpEntityUdpDscPort InetPortNumber, mplsLdpEntityMaxPduLength Unsigned32, mplsLdpEntityKeepAliveHoldTimer Unsigned32, mplsLdpEntityHelloHoldTimer Unsigned32, mplsLdpEntityInitSessionThreshold Integer32, mplsLdpEntityLabelDistMethod MplsLabelDistributionMethod, mplsLdpEntityLabelRetentionMode MplsRetentionMode, mplsLdpEntityPathVectorLimit Integer32, mplsLdpEntityHopCountLimit Integer32, mplsLdpEntityTransportAddrKind INTEGER, mplsLdpEntityTargetPeer TruthValue, mplsLdpEntityTargetPeerAddrType InetAddressType, mplsLdpEntityTargetPeerAddr InetAddress, mplsLdpEntityLabelType MplsLdpLabelType, mplsLdpEntityDiscontinuityTime TimeStamp, mplsLdpEntityStorageType StorageType, mplsLdpEntityRowStatus RowStatus } mplsLdpEntityLdpId OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The LDP identifier." REFERENCE "RFC3036, LDP Specification, Section on LDP Identifiers." ::= { mplsLdpEntityEntry 1 } mplsLdpEntityIndex OBJECT-TYPE SYNTAX IndexInteger MAX-ACCESS not-accessible STATUS current DESCRIPTION "This index is used as a secondary index to uniquely identify this row. Before creating a row in this table, the 'mplsLdpEntityIndexNext' object should be retrieved. That value should be used for the value of this index when creating a row in this table. NOTE: if a value of zero (0) is retrieved, that indicates that no rows can be created in this table at this time. A secondary index (this object) is meaningful to some but not all, LDP implementations. For example an LDP implementation which uses PPP would use this index to differentiate PPP sub-links. Another way to use this index is to give this the value of ifIndex. However, this is dependant on the implementation." ::= { mplsLdpEntityEntry 2 } mplsLdpEntityProtocolVersion OBJECT-TYPE SYNTAX Unsigned32(1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The version number of the LDP protocol which will be used in the session initialization message. Section 3.5.3 in the LDP Specification specifies that the version of the LDP protocol is negotiated during session establishment. The value of this object represents the value that is sent in the initialization message." REFERENCE "RFC3036, LDP Specification, Section 3.5.3 Initialization Message." DEFVAL { 1 } ::= { mplsLdpEntityEntry 3 } mplsLdpEntityAdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative status of this LDP Entity. If this object is changed from 'enable' to 'disable' and this entity has already attempted to establish contact with a Peer, then all contact with that Peer is lost and all information from that Peer needs to be removed from the MIB. (This implies that the network management subsystem should clean up any related entry in the mplsLdpPeerTable. This further implies that a 'tear-down' for that session is issued and the session and all information related to that session cease to exist). At this point the operator is able to change values which are related to this entity. When the admin status is set back to 'enable', then this Entity will attempt to establish a new session with the Peer." DEFVAL { enable } ::= { mplsLdpEntityEntry 4 } mplsLdpEntityOperStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operational status of this LDP Entity. The value of unknown(1) indicates that the operational status cannot be determined at this time. The value of unknown should be a transient condition before changing to enabled(2) or disabled(3)." ::= { mplsLdpEntityEntry 5 } mplsLdpEntityTcpPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The TCP Port for LDP. The default value is the well-known value of this port." REFERENCE "RFC3036, LDP Specification, Section 3.10, Well-known Numbers, and Section 3.10.1. UDP and TCP Ports." DEFVAL { 646 } ::= { mplsLdpEntityEntry 6 } mplsLdpEntityUdpDscPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The UDP Discovery Port for LDP. The default value is the well-known value for this port." REFERENCE "RFC3036, LDP Specification, Section 2.4.1, Basic Discovery Mechanism, Section 2.4.2, Extended Discovery Mechanism, Section 3.10, Well-known Numbers, and Section 3.10.1. UDP and TCP Ports." DEFVAL { 646 } ::= { mplsLdpEntityEntry 7 } mplsLdpEntityMaxPduLength OBJECT-TYPE SYNTAX Unsigned32 (256..65535) UNITS "octets" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum PDU Length that is sent in the Common Session Parameters of an Initialization Message. According to the LDP Specification [RFC3036] a value of 255 or less specifies the default maximum length of 4096 octets, this is why the value of this object starts at 256. The operator should explicitly choose the default value (i.e., 4096), or some other value. The receiving LSR MUST calculate the maximum PDU length for the session by using the smaller of its and its peer's proposals for Max PDU Length." REFERENCE "RFC3036, LDP Specification, Section 3.5.3. Initialization Message." DEFVAL { 4096 } ::= { mplsLdpEntityEntry 8 } mplsLdpEntityKeepAliveHoldTimer OBJECT-TYPE SYNTAX Unsigned32 (1..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The 16-bit integer value which is the proposed keep alive hold timer for this LDP Entity." DEFVAL { 40 } ::= { mplsLdpEntityEntry 9 } mplsLdpEntityHelloHoldTimer OBJECT-TYPE SYNTAX Unsigned32 (0..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The 16-bit integer value which is the proposed Hello hold timer for this LDP Entity. The Hello Hold time in seconds. An LSR maintains a record of Hellos received from potential peers. This object represents the Hold Time in the Common Hello Parameters TLV of the Hello Message. A value of 0 is a default value and should be interpretted in conjunction with the mplsLdpEntityTargetPeer object. If the value of this object is 0: if the value of the mplsLdpEntityTargetPeer object is false(2), then this specifies that the Hold Time's actual default value is 15 seconds (i.e., the default Hold time for Link Hellos is 15 seconds). Otherwise if the value of the mplsLdpEntityTargetPeer object is true(1), then this specifies that the Hold Time's actual default value is 45 seconds (i.e., the default Hold time for Targeted Hellos is 45 seconds). A value of 65535 means infinite (i.e., wait forever). All other values represent the amount of time in seconds to wait for a Hello Message. Setting the hold time to a value smaller than 15 is not recommended, although not forbidden according to RFC3036." REFERENCE "RFC3036, LDP Specification, Section 3.5.2., Hello Message." DEFVAL { 0 } ::= { mplsLdpEntityEntry 10 } mplsLdpEntityInitSessionThreshold OBJECT-TYPE SYNTAX Integer32(0..100) MAX-ACCESS read-create STATUS current DESCRIPTION "When attempting to establish a session with a given Peer, the given LDP Entity should send out the SNMP notification, 'mplsLdpInitSessionThresholdExceeded', when the number of Session Initialization messages sent exceeds this threshold. The notification is used to notify an operator when this Entity and its Peer are possibly engaged in an endless sequence of messages as each NAKs the other's Initialization messages with Error Notification messages. Setting this threshold which triggers the notification is one way to notify the operator. The notification should be generated each time this threshold is exceeded and for every subsequent Initialization message which is NAK'd with an Error Notification message after this threshold is exceeded. A value of 0 (zero) for this object indicates that the threshold is infinity, thus the SNMP notification will never be generated." REFERENCE "RFC3036, LDP Specification, Section 2.5.3 Session Initialization." DEFVAL { 8 } ::= { mplsLdpEntityEntry 11 } mplsLdpEntityLabelDistMethod OBJECT-TYPE SYNTAX MplsLabelDistributionMethod MAX-ACCESS read-create STATUS current DESCRIPTION "For any given LDP session, the method of label distribution must be specified." ::= { mplsLdpEntityEntry 12 } mplsLdpEntityLabelRetentionMode OBJECT-TYPE SYNTAX MplsRetentionMode MAX-ACCESS read-create STATUS current DESCRIPTION "The LDP Entity can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized label mappings are retained only if they will be used to forward packets, i.e., if label came from a valid next hop. If the value of this object is liberal(2) then all advertized label mappings are retained whether they are from a valid next hop or not." ::= { mplsLdpEntityEntry 13 } mplsLdpEntityPathVectorLimit OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "If the value of this object is 0 (zero) then Loop Detection for Path Vectors is disabled. Otherwise, if this object has a value greater than zero, then Loop Dection for Path Vectors is enabled, and the Path Vector Limit is this value. Also, the value of the object, 'mplsLdpLsrLoopDetectionCapable', must be set to either 'pathVector(4)' or 'hopCountAndPathVector(5)', if this object has a value greater than 0 (zero), otherwise it is ignored." REFERENCE "RFC3036, LDP Specification, Section 2.8 Loop Dection, Section 3.4.5 Path Vector TLV." ::= { mplsLdpEntityEntry 14 } mplsLdpEntityHopCountLimit OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "If the value of this object is 0 (zero), then Loop Detection using Hop Counters is disabled. If the value of this object is greater than 0 (zero) then Loop Detection using Hop Counters is enabled, and this object specifies this Entity's maximum allowable value for the Hop Count. Also, the value of the object mplsLdpLsrLoopDetectionCapable must be set to either 'hopCount(3)' or 'hopCountAndPathVector(5)' if this object has a value greater than 0 (zero), otherwise it is ignored." DEFVAL { 0 } ::= { mplsLdpEntityEntry 15 } mplsLdpEntityTransportAddrKind OBJECT-TYPE SYNTAX INTEGER { interface(1), loopback(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies whether the loopback or interface address is to be used as the transport address in the transport address TLV of the hello message. If the value is interface(1), then the IP address of the interface from which hello messages are sent is used as the transport address in the hello message. Otherwise, if the value is loopback(2), then the IP address of the loopback interface is used as the transport address in the hello message." DEFVAL { loopback } ::= { mplsLdpEntityEntry 16 } mplsLdpEntityTargetPeer OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If this LDP entity uses targeted peer then set this to true." DEFVAL { false } ::= { mplsLdpEntityEntry 17 } mplsLdpEntityTargetPeerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the internetwork layer address used for the Extended Discovery. This object indicates how the value of mplsLdpEntityTargetPeerAddr is to be interpreted." ::= { mplsLdpEntityEntry 18 } mplsLdpEntityTargetPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the internetwork layer address used for the Extended Discovery. The value of mplsLdpEntityTargetPeerAddrType specifies how this address is to be interpreted." ::= { mplsLdpEntityEntry 19 } mplsLdpEntityLabelType OBJECT-TYPE SYNTAX MplsLdpLabelType MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the optional parameters for the LDP Initialization Message. If the value is generic(1) then no optional parameters will be sent in the LDP Initialization message associated with this Entity. If the value is atmParameters(2) then a row must be created in the mplsLdpEntityAtmTable, which corresponds to this entry. If the value is frameRelayParameters(3) then a row must be created in the mplsLdpEntityFrameRelayTable, which corresponds to this entry." REFERENCE "RFC3036, LDP Specification, Section 3.5.3., Initialization Message." ::= { mplsLdpEntityEntry 20 } mplsLdpEntityDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this entity's counters suffered a discontinuity. The relevant counters are the specific instances associated with this entity of any Counter32 object contained in the 'mplsLdpEntityStatsTable'. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value." ::= { mplsLdpEntityEntry 21 } mplsLdpEntityStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL{ nonVolatile } ::= { mplsLdpEntityEntry 22 } mplsLdpEntityRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable, which enables a new session to be initiated." ::= { mplsLdpEntityEntry 23 } -- -- The MPLS LDP Entity Statistics Table -- mplsLdpEntityStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpEntityStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is a read-only table which augments the mplsLdpEntityTable. The purpose of this table is to keep statistical information about the LDP Entities on the LSR." ::= { mplsLdpEntityObjects 4 } mplsLdpEntityStatsEntry OBJECT-TYPE SYNTAX MplsLdpEntityStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table contains statistical information about an LDP Entity. Some counters contained in a row are for fatal errors received during a former LDP Session associated with this entry. For example, an LDP PDU received on a TCP connection during an LDP Session contains a fatal error. That error is counted here, because the session is terminated. If the error is NOT fatal (i.e., the Session remains), then the error is counted in the mplsLdpSessionStatsEntry." AUGMENTS { mplsLdpEntityEntry } ::= { mplsLdpEntityStatsTable 1 } MplsLdpEntityStatsEntry ::= SEQUENCE { mplsLdpEntityStatsSessionAttempts Counter32, mplsLdpEntityStatsSessionRejectedNoHelloErrors Counter32, mplsLdpEntityStatsSessionRejectedAdErrors Counter32, mplsLdpEntityStatsSessionRejectedMaxPduErrors Counter32, mplsLdpEntityStatsSessionRejectedLRErrors Counter32, mplsLdpEntityStatsBadLdpIdentifierErrors Counter32, mplsLdpEntityStatsBadPduLengthErrors Counter32, mplsLdpEntityStatsBadMessageLengthErrors Counter32, mplsLdpEntityStatsBadTlvLengthErrors Counter32, mplsLdpEntityStatsMalformedTlvValueErrors Counter32, mplsLdpEntityStatsKeepAliveTimerExpErrors Counter32, mplsLdpEntityStatsShutdownReceivedNotifications Counter32, mplsLdpEntityStatsShutdownSentNotifications Counter32 } mplsLdpEntityStatsSessionAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the Session Initialization messages which were sent or received by this LDP Entity and were NAK'd. In other words, this counter counts the number of session initializations that failed. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 1 } mplsLdpEntityStatsSessionRejectedNoHelloErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the Session Rejected/No Hello Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 2 } mplsLdpEntityStatsSessionRejectedAdErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the Session Rejected/Parameters Advertisement Mode Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 3 } mplsLdpEntityStatsSessionRejectedMaxPduErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the Session Rejected/Parameters Max Pdu Length Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 4 } mplsLdpEntityStatsSessionRejectedLRErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the Session Rejected/Parameters Label Range Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 5 } mplsLdpEntityStatsBadLdpIdentifierErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Bad LDP Identifier Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 6 } mplsLdpEntityStatsBadPduLengthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Bad PDU Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 7 } mplsLdpEntityStatsBadMessageLengthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Bad Message Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 8 } mplsLdpEntityStatsBadTlvLengthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Bad TLV Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 9 } mplsLdpEntityStatsMalformedTlvValueErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Malformed TLV Value Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 10 } mplsLdpEntityStatsKeepAliveTimerExpErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Session Keep Alive Timer Expired Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 11 } mplsLdpEntityStatsShutdownReceivedNotifications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Shutdown Notifications received related to session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 12 } mplsLdpEntityStatsShutdownSentNotifications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Shutdown Notfications sent related to session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 13 } -- -- The MPLS LDP Peer Table -- mplsLdpSessionObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 3 } mplsLdpPeerLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the most recent addition or deletion to/from the mplsLdpPeerTable/mplsLdpSessionTable." ::= { mplsLdpSessionObjects 1 } mplsLdpPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about LDP peers known by Entities in the mplsLdpEntityTable. The information in this table is based on information from the Entity-Peer interaction during session initialization but is not appropriate for the mplsLdpSessionTable, because objects in this table may or may not be used in session establishment." ::= { mplsLdpSessionObjects 2 } mplsLdpPeerEntry OBJECT-TYPE SYNTAX MplsLdpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single Peer which is related to a Session. This table is augmented by the mplsLdpSessionTable." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId } ::= { mplsLdpPeerTable 1 } MplsLdpPeerEntry ::= SEQUENCE { mplsLdpPeerLdpId MplsLdpIdentifier, mplsLdpPeerLabelDistMethod MplsLabelDistributionMethod, mplsLdpPeerPathVectorLimit Integer32, mplsLdpPeerTransportAddrType InetAddressType, mplsLdpPeerTransportAddr InetAddress } mplsLdpPeerLdpId OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The LDP identifier of this LDP Peer." ::= { mplsLdpPeerEntry 1 } mplsLdpPeerLabelDistMethod OBJECT-TYPE SYNTAX MplsLabelDistributionMethod MAX-ACCESS read-only STATUS current DESCRIPTION "For any given LDP session, the method of label distribution must be specified." ::= { mplsLdpPeerEntry 2 } mplsLdpPeerPathVectorLimit OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "If the value of this object is 0 (zero) then Loop Dection for Path Vectors for this Peer is disabled. Otherwise, if this object has a value greater than zero, then Loop Dection for Path Vectors for this Peer is enabled and the Path Vector Limit is this value." REFERENCE "RFC3036, LDP Specification, Section 2.8 Loop Dection, Section 3.4.5 Path Vector TLV." ::= { mplsLdpPeerEntry 3 } mplsLdpPeerTransportAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the Internet address for the mplsLdpPeerTransportAddr object. The LDP specification describes this as being either an IPv4 Transport Address or IPv6 Transport Address which is used in opening the LDP session's TCP connection, or if the optional TLV is not present, then this is the IPv4/IPv6 source address for the UPD packet carrying the Hellos. This object specifies how the value of the mplsLdpPeerTransportAddr object should be interpreted." REFERENCE "RFC3036, LDP Specification, Section 2.5.2 Transport Connection Establishment and Section 3.5.2.1 Hello Message Procedures." ::= { mplsLdpPeerEntry 4 } mplsLdpPeerTransportAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Internet address advertised by the peer in the Hello Message or the Hello source address. The type of this address is specified by the value of the mplsLdpPeerTransportAddrType object." REFERENCE "RFC3036, LDP Specification, Section 2.5.2 Transport Connection Establishment and Section 3.5.2.1 Hello Message Procedures." ::= { mplsLdpPeerEntry 5 } -- -- The MPLS LDP Sessions Table -- mplsLdpSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Sessions between the LDP Entities and LDP Peers. This table AUGMENTS the mplsLdpPeerTable. Each row in this table represents a single session." ::= { mplsLdpSessionObjects 3 } mplsLdpSessionEntry OBJECT-TYPE SYNTAX MplsLdpSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a single session between an LDP Entity and LDP Peer. The information contained in a row is read-only. Please note: the Path Vector Limit for the Session is the value which is configured in the corresponding mplsLdpEntityEntry. The Peer's Path Vector Limit is in the mplsLdpPeerPathVectorLimit object in the mplsLdpPeerTable. Values which may differ from those configured are noted in the objects of this table, the mplsLdpAtmSessionTable and the mplsLdpFrameRelaySessionTable. A value will differ if it was negotiated between the Entity and the Peer. Values may or may not be negotiated. For example, if the values are the same then no negotiation takes place. If they are negotiated, then they may differ." AUGMENTS { mplsLdpPeerEntry } ::= { mplsLdpSessionTable 1 } MplsLdpSessionEntry ::= SEQUENCE { mplsLdpSessionStateLastChange TimeStamp, mplsLdpSessionState INTEGER, mplsLdpSessionRole INTEGER, mplsLdpSessionProtocolVersion Unsigned32, mplsLdpSessionKeepAliveHoldTimeRem TimeInterval, mplsLdpSessionKeepAliveTime Unsigned32, mplsLdpSessionMaxPduLength Unsigned32, mplsLdpSessionDiscontinuityTime TimeStamp } mplsLdpSessionStateLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time this Session entered its current state as denoted by the mplsLdpSessionState object." ::= { mplsLdpSessionEntry 1 } mplsLdpSessionState OBJECT-TYPE SYNTAX INTEGER { nonexistent(1), initialized(2), openrec(3), opensent(4), operational(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the session, all of the states 1 to 5 are based on the state machine for session negotiation behavior." REFERENCE "RFC3036, LDP Specification, Section 2.5.4, Initialization State Machine." ::= { mplsLdpSessionEntry 2 } mplsLdpSessionRole OBJECT-TYPE SYNTAX INTEGER { unknown(1), active(2), passive(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "During session establishment the LSR/LER takes either the active role or the passive role based on address comparisons. This object indicates whether this LSR/LER was behaving in an active role or passive role during this session's establishment. The value of unknown(1), indicates that the role is not able to be determined at the present time." REFERENCE "RFC3036, LDP Specification, Section 2.5.3., Session Initialization" ::= { mplsLdpSessionEntry 3 } mplsLdpSessionProtocolVersion OBJECT-TYPE SYNTAX Unsigned32(1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the LDP Protocol which this session is using. This is the version of the LDP protocol which has been negotiated during session initialization." REFERENCE "RFC3036, LDP Specification, Section 3.5.3, Initialization Message." ::= { mplsLdpSessionEntry 4 } mplsLdpSessionKeepAliveHoldTimeRem OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "The keep alive hold time remaining for this session." ::= { mplsLdpSessionEntry 5 } mplsLdpSessionKeepAliveTime OBJECT-TYPE SYNTAX Unsigned32 (1..65535) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The negotiated KeepAlive Time which represents the amount of seconds between keep alive messages. The mplsLdpEntityKeepAliveHoldTimer related to this Session is the value that was proposed as the KeepAlive Time for this session. This value is negotiated during session initialization between the entity's proposed value (i.e., the value configured in mplsLdpEntityKeepAliveHoldTimer) and the peer's proposed KeepAlive Hold Timer value. This value is the smaller of the two proposed values." REFERENCE "RFC3036, LDP Specification, Section 3.5.3, Initialization Message." ::= { mplsLdpSessionEntry 6 } mplsLdpSessionMaxPduLength OBJECT-TYPE SYNTAX Unsigned32 (1..65535) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of maximum allowable length for LDP PDUs for this session. This value may have been negotiated during the Session Initialization. This object is related to the mplsLdpEntityMaxPduLength object. The mplsLdpEntityMaxPduLength object specifies the requested LDP PDU length, and this object reflects the negotiated LDP PDU length between the Entity and the Peer." REFERENCE "RFC3036, LDP Specification, Section 3.5.3, Initialization Message." ::= { mplsLdpSessionEntry 7 } mplsLdpSessionDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this session's counters suffered a discontinuity. The relevant counters are the specific instances associated with this session of any Counter32 object contained in the mplsLdpSessionStatsTable. The initial value of this object is the value of sysUpTime when the entry was created in this table. Also, a command generator can distinguish when a session between a given Entity and Peer goes away and a new session is established. This value would change and thus indicate to the command generator that this is a different session." ::= { mplsLdpSessionEntry 8 } -- -- The MPLS LDP Session Statistics Table -- mplsLdpSessionStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpSessionStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of statistics for Sessions between LDP Entities and LDP Peers. This table AUGMENTS the mplsLdpPeerTable." ::= { mplsLdpSessionObjects 4 } mplsLdpSessionStatsEntry OBJECT-TYPE SYNTAX MplsLdpSessionStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents statistical information on a single session between an LDP Entity and LDP Peer." AUGMENTS { mplsLdpPeerEntry } ::= { mplsLdpSessionStatsTable 1 } MplsLdpSessionStatsEntry ::= SEQUENCE { mplsLdpSessionStatsUnknownMesTypeErrors Counter32, mplsLdpSessionStatsUnknownTlvErrors Counter32 } mplsLdpSessionStatsUnknownMesTypeErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Unknown Message Type Errors detected by this LSR/LER during this session. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpSessionDiscontinuityTime." ::= { mplsLdpSessionStatsEntry 1 } mplsLdpSessionStatsUnknownTlvErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Unknown TLV Errors detected by this LSR/LER during this session. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpSessionDiscontinuityTime." ::= { mplsLdpSessionStatsEntry 2 } -- -- The MPLS LDP Hello Adjacency Table -- mplsLdpHelloAdjacencyObjects OBJECT IDENTIFIER ::= { mplsLdpSessionObjects 5 } mplsLdpHelloAdjacencyTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpHelloAdjacencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Hello Adjacencies for Sessions." ::= { mplsLdpHelloAdjacencyObjects 1 } mplsLdpHelloAdjacencyEntry OBJECT-TYPE SYNTAX MplsLdpHelloAdjacencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello Adjacencies." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsLdpHelloAdjacencyIndex } ::= { mplsLdpHelloAdjacencyTable 1 } MplsLdpHelloAdjacencyEntry ::= SEQUENCE { mplsLdpHelloAdjacencyIndex Unsigned32, mplsLdpHelloAdjacencyHoldTimeRem TimeInterval, mplsLdpHelloAdjacencyHoldTime Unsigned32, mplsLdpHelloAdjacencyType INTEGER } mplsLdpHelloAdjacencyIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An identifier for this specific adjacency." ::= { mplsLdpHelloAdjacencyEntry 1 } mplsLdpHelloAdjacencyHoldTimeRem OBJECT-TYPE SYNTAX TimeInterval UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "If the value of this object is 65535, this means that the hold time is infinite (i.e., wait forever). Otherwise, the time remaining for this Hello Adjacency to receive its next Hello Message. This interval will change when the 'next' Hello Message which corresponds to this Hello Adjacency is received unless it is infinite." ::= { mplsLdpHelloAdjacencyEntry 2 } mplsLdpHelloAdjacencyHoldTime OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The Hello hold time which is negotiated between the Entity and the Peer. The entity associated with this Hello Adjacency issues a proposed Hello Hold Time value in the mplsLdpEntityHelloHoldTimer object. The peer also proposes a value and this object represents the negotiated value. A value of 0 means the default, which is 15 seconds for Link Hellos and 45 seconds for Targeted Hellos. A value of 65535 indicates an infinite hold time." REFERENCE "RFC3036, LDP Specification, Section 3.5.2 Hello Message" ::= { mplsLdpHelloAdjacencyEntry 3 } mplsLdpHelloAdjacencyType OBJECT-TYPE SYNTAX INTEGER { link(1), targeted(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This adjacency is the result of a 'link' hello if the value of this object is link(1). Otherwise, it is a result of a 'targeted' hello, targeted(2)." ::= { mplsLdpHelloAdjacencyEntry 4 } -- -- Session Label (LSP) Mapping to LSR MIB's -- In Segment LIB Information. -- -- -- NOTE: the next 2 tables map to the -- MPLS-LSR-STD-MIB's MplsInSegmentTable -- and MplsOutSegmentTable. The -- cross-connect (XC) information is not -- represented here as it can be gleaned -- from the MPLS-LSR-STD-MIB. -- mplsInSegmentLdpLspTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsInSegmentLdpLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of LDP LSP's which map to the mplsInSegmentTable in the MPLS-LSR-STD-MIB module." ::= { mplsLdpSessionObjects 6 } mplsInSegmentLdpLspEntry OBJECT-TYPE SYNTAX MplsInSegmentLdpLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a single LDP LSP which is represented by a session's index triple (mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId) AND the index for the mplsInSegmentTable (mplsInSegmentLdpLspLabelIndex) from the MPLS-LSR-STD-MIB. The information contained in a row is read-only." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsInSegmentLdpLspIndex } ::= { mplsInSegmentLdpLspTable 1 } MplsInSegmentLdpLspEntry ::= SEQUENCE { mplsInSegmentLdpLspIndex MplsIndexType, mplsInSegmentLdpLspLabelType MplsLdpLabelType, mplsInSegmentLdpLspType MplsLspType } mplsInSegmentLdpLspIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This contains the same value as the mplsInSegmentIndex in the MPLS-LSR-STD-MIB's mplsInSegmentTable." ::= { mplsInSegmentLdpLspEntry 1 } mplsInSegmentLdpLspLabelType OBJECT-TYPE SYNTAX MplsLdpLabelType MAX-ACCESS read-only STATUS current DESCRIPTION "The Layer 2 Label Type." ::= { mplsInSegmentLdpLspEntry 2 } mplsInSegmentLdpLspType OBJECT-TYPE SYNTAX MplsLspType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of LSP connection." ::= { mplsInSegmentLdpLspEntry 3 } -- -- Session Label (LSP) Mapping to LSR MIB's -- Out Segment LIB Information. -- mplsOutSegmentLdpLspTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsOutSegmentLdpLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of LDP LSP's which map to the mplsOutSegmentTable in the MPLS-LSR-STD-MIB." ::= { mplsLdpSessionObjects 7 } mplsOutSegmentLdpLspEntry OBJECT-TYPE SYNTAX MplsOutSegmentLdpLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a single LDP LSP which is represented by a session's index triple (mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId) AND the index (mplsOutSegmentLdpLspIndex) for the mplsOutSegmentTable. The information contained in a row is read-only." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsOutSegmentLdpLspIndex } ::= { mplsOutSegmentLdpLspTable 1 } MplsOutSegmentLdpLspEntry ::= SEQUENCE { mplsOutSegmentLdpLspIndex MplsIndexType, mplsOutSegmentLdpLspLabelType MplsLdpLabelType, mplsOutSegmentLdpLspType MplsLspType } mplsOutSegmentLdpLspIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This contains the same value as the mplsOutSegmentIndex in the MPLS-LSR-STD-MIB's mplsOutSegmentTable." ::= { mplsOutSegmentLdpLspEntry 1 } mplsOutSegmentLdpLspLabelType OBJECT-TYPE SYNTAX MplsLdpLabelType MAX-ACCESS read-only STATUS current DESCRIPTION "The Layer 2 Label Type." ::= { mplsOutSegmentLdpLspEntry 2 } mplsOutSegmentLdpLspType OBJECT-TYPE SYNTAX MplsLspType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of LSP connection." ::= { mplsOutSegmentLdpLspEntry 3 } -- -- Mpls FEC Table -- mplsFecObjects OBJECT IDENTIFIER ::= { mplsLdpSessionObjects 8 } mplsFecLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the most recent addition/deletion of an entry to/from the mplsLdpFectTable or the most recent change in values to any objects in the mplsLdpFecTable. If no such changes have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value." ::= { mplsFecObjects 1 } mplsFecIndexNext OBJECT-TYPE SYNTAX IndexIntegerNextFree MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for mplsFecIndex when creating entries in the mplsFecTable. The value 0 indicates that no unassigned entries are available." ::= { mplsFecObjects 2 } mplsFecTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsFecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the FEC (Forwarding Equivalence Class) Information associated with an LSP." ::= { mplsFecObjects 3 } mplsFecEntry OBJECT-TYPE SYNTAX MplsFecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row represents a single FEC Element." INDEX { mplsFecIndex } ::= { mplsFecTable 1 } MplsFecEntry ::= SEQUENCE { mplsFecIndex IndexInteger, mplsFecType INTEGER, mplsFecAddrType InetAddressType, mplsFecAddr InetAddress, mplsFecAddrPrefixLength InetAddressPrefixLength, mplsFecStorageType StorageType, mplsFecRowStatus RowStatus } mplsFecIndex OBJECT-TYPE SYNTAX IndexInteger MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index which uniquely identifies this entry." ::= { mplsFecEntry 1 } mplsFecType OBJECT-TYPE SYNTAX INTEGER { prefix(1), hostAddress(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the FEC. If the value of this object is 'prefix(1)' then the FEC type described by this row is an address prefix. If the value of this object is 'hostAddress(2)' then the FEC type described by this row is a host address." REFERENCE "RFC3036, Section 3.4.1. FEC TLV." ::= { mplsFecEntry 2 } mplsFecAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object is the type of the Internet address. The value of this object, decides how the value of the mplsFecAddr object is interpreted." REFERENCE "RFC3036, Section 3.4.1. FEC TLV." ::= { mplsFecEntry 4 } mplsFecAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object is interpreted based on the value of the 'mplsFecAddrType' object. This address is then further interpretted as an being used with the address prefix, or as the host address. This further interpretation is indicated by the 'mplsFecType' object. In other words, the FEC element is populated according to the Prefix FEC Element value encoding, or the Host Address FEC Element encoding." REFERENCE "RFC3036, Section 3.4.1 FEC TLV." ::= { mplsFecEntry 5 } mplsFecAddrPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-create STATUS current DESCRIPTION "If the value of the 'mplsFecType' is 'hostAddress(2)' then this object is undefined. If the value of 'mplsFecType' is 'prefix(1)' then the value of this object is the length in bits of the address prefix represented by 'mplsFecAddr', or zero. If the value of this object is zero, this indicates that the prefix matches all addresses. In this case the address prefix MUST also be zero (i.e., 'mplsFecAddr' should have the value of zero.)" REFERENCE "RFC3036, Section 3.4.1. FEC TLV." DEFVAL { 0 } ::= { mplsFecEntry 3 } mplsFecStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { mplsFecEntry 6 } mplsFecRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. If the value of this object is 'active(1)', then none of the writable objects of this entry can be modified, except to set this object to 'destroy(6)'. NOTE: if this row is being referenced by any entry in the mplsLdpLspFecTable, then a request to destroy this row, will result in an inconsistentValue error." ::= { mplsFecEntry 7 } -- -- LDP LSP FEC Table -- mplsLdpLspFecLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the most recent addition/deletion of an entry to/from the mplsLdpLspFecTable or the most recent change in values to any objects in the mplsLdpLspFecTable. If no such changes have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value." ::= { mplsLdpSessionObjects 9 } mplsLdpLspFecTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpLspFecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table which shows the relationship between LDP LSPs and FECs. Each row represents a single LDP LSP to FEC association." ::= { mplsLdpSessionObjects 10 } mplsLdpLspFecEntry OBJECT-TYPE SYNTAX MplsLdpLspFecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry represents a LDP LSP to FEC association." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsLdpLspFecSegment, mplsLdpLspFecSegmentIndex, mplsLdpLspFecIndex } ::= { mplsLdpLspFecTable 1 } MplsLdpLspFecEntry ::= SEQUENCE { mplsLdpLspFecSegment INTEGER, mplsLdpLspFecSegmentIndex MplsIndexType, mplsLdpLspFecIndex IndexInteger, mplsLdpLspFecStorageType StorageType, mplsLdpLspFecRowStatus RowStatus } mplsLdpLspFecSegment OBJECT-TYPE SYNTAX INTEGER { inSegment(1), outSegment(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the value is inSegment(1), then this indicates that the following index, mplsLdpLspFecSegmentIndex, contains the same value as the mplsInSegmentLdpLspIndex. Otherwise, if the value of this object is outSegment(2), then this indicates that following index, mplsLdpLspFecSegmentIndex, contains the same value as the mplsOutSegmentLdpLspIndex." ::= { mplsLdpLspFecEntry 1 } mplsLdpLspFecSegmentIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This index is interpretted by using the value of the mplsLdpLspFecSegment. If the mplsLdpLspFecSegment is inSegment(1), then this index has the same value as mplsInSegmentLdpLspIndex. If the mplsLdpLspFecSegment is outSegment(2), then this index has the same value as mplsOutSegmentLdpLspIndex." ::= { mplsLdpLspFecEntry 2 } mplsLdpLspFecIndex OBJECT-TYPE SYNTAX IndexInteger MAX-ACCESS not-accessible STATUS current DESCRIPTION "This index identifies the FEC entry in the mplsFecTable associated with this session. In other words, the value of this index is the same as the value of the mplsFecIndex that denotes the FEC associated with this Session." ::= { mplsLdpLspFecEntry 3 } mplsLdpLspFecStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { mplsLdpLspFecEntry 4 } mplsLdpLspFecRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. If the value of this object is 'active(1)', then none of the writable objects of this entry can be modified. The Agent should delete this row when the session ceases to exist. If an operator wants to associate the session with a different FEC, the recommended procedure is (as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object) is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. This will also cause this entry to be deleted. Then, set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated. Once the session is initiated, an entry may be added to this table to associate the new session with a FEC." ::= { mplsLdpLspFecEntry 5 } -- -- Address Message/Address Withdraw Message Information -- -- This information is associated with a specific Session -- because Label Address Messages are sent after session -- initialization has taken place. -- mplsLdpSessionPeerAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpSessionPeerAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table 'extends' the mplsLdpSessionTable. This table is used to store Label Address Information from Label Address Messages received by this LSR from Peers. This table is read-only and should be updated when Label Withdraw Address Messages are received, i.e., Rows should be deleted as appropriate. NOTE: since more than one address may be contained in a Label Address Message, this table 'sparse augments', the mplsLdpSessionTable's information." ::= { mplsLdpSessionObjects 11 } mplsLdpSessionPeerAddrEntry OBJECT-TYPE SYNTAX MplsLdpSessionPeerAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a session's single next hop address which was advertised in an Address Message from the LDP peer. The information contained in a row is read-only." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsLdpSessionPeerAddrIndex } ::= { mplsLdpSessionPeerAddrTable 1 } MplsLdpSessionPeerAddrEntry ::= SEQUENCE { mplsLdpSessionPeerAddrIndex Unsigned32, mplsLdpSessionPeerNextHopAddrType InetAddressType, mplsLdpSessionPeerNextHopAddr InetAddress } mplsLdpSessionPeerAddrIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index which uniquely identifies this entry within a given session." ::= { mplsLdpSessionPeerAddrEntry 1 } mplsLdpSessionPeerNextHopAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The internetwork layer address type of this Next Hop Address as specified in the Label Address Message associated with this Session. The value of this object indicates how to interpret the value of mplsLdpSessionPeerNextHopAddr." ::= { mplsLdpSessionPeerAddrEntry 2 } mplsLdpSessionPeerNextHopAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The next hop address. The type of this address is specified by the value of the mplsLdpSessionPeerNextHopAddrType." REFERENCE "RFC3036, Section 2.7. LDP Identifiers and Next Hop Addresses" ::= { mplsLdpSessionPeerAddrEntry 3 } --- --- Notifications --- mplsLdpInitSessionThresholdExceeded NOTIFICATION-TYPE OBJECTS { mplsLdpEntityInitSessionThreshold } STATUS current DESCRIPTION "This notification is generated when the value of the 'mplsLdpEntityInitSessionThreshold' object is not zero, and the number of Session Initialization messages exceeds the value of the 'mplsLdpEntityInitSessionThreshold' object." ::= { mplsLdpNotifications 1 } mplsLdpPathVectorLimitMismatch NOTIFICATION-TYPE OBJECTS { mplsLdpEntityPathVectorLimit, mplsLdpPeerPathVectorLimit } STATUS current DESCRIPTION "This notification is sent when the 'mplsLdpEntityPathVectorLimit' does NOT match the value of the 'mplsLdpPeerPathVectorLimit' for a specific Entity." REFERENCE "RFC3036, LDP Specification, Section 3.5.3." ::= { mplsLdpNotifications 2 } mplsLdpSessionUp NOTIFICATION-TYPE OBJECTS { mplsLdpSessionState, mplsLdpSessionDiscontinuityTime, mplsLdpSessionStatsUnknownMesTypeErrors, mplsLdpSessionStatsUnknownTlvErrors } STATUS current DESCRIPTION "If this notification is sent when the value of 'mplsLdpSessionState' enters the 'operational(5)' state." ::= { mplsLdpNotifications 3 } mplsLdpSessionDown NOTIFICATION-TYPE OBJECTS { mplsLdpSessionState, mplsLdpSessionDiscontinuityTime, mplsLdpSessionStatsUnknownMesTypeErrors, mplsLdpSessionStatsUnknownTlvErrors } STATUS current DESCRIPTION "This notification is sent when the value of 'mplsLdpSessionState' leaves the 'operational(5)' state." ::= { mplsLdpNotifications 4 } --**************************************************************** -- Module Conformance Statement --**************************************************************** mplsLdpGroups OBJECT IDENTIFIER ::= { mplsLdpConformance 1 } mplsLdpCompliances OBJECT IDENTIFIER ::= { mplsLdpConformance 2 } -- -- Full Compliance -- mplsLdpModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Module is implemented with support for read-create and read-write. In other words, both monitoring and configuration are available when using this MODULE-COMPLIANCE." MODULE -- this module MANDATORY-GROUPS { mplsLdpGeneralGroup, mplsLdpNotificationsGroup } GROUP mplsLdpLspGroup DESCRIPTION "This group must be supported if the LSR MIB is implemented, specifically the mplsInSegmentTable, the mplsOutSegmentTable or the mplsXCTable." OBJECT mplsLdpEntityTargetPeerAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpEntityTargetPeerAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation is only required to support IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpEntityRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notInService is not required." OBJECT mplsFecAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsFecAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation is only required to support IPv4 and globally unique IPv6 addresses." OBJECT mplsFecRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notInService is not required." OBJECT mplsLdpLspFecRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notInService is not required." OBJECT mplsLdpSessionPeerNextHopAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpSessionPeerNextHopAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation is only required to support IPv4 and globally unique IPv6 addresses." ::= { mplsLdpCompliances 1 } -- -- Read-Only Compliance -- mplsLdpModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Module is implemented with support for read-only. In other words, only monitoring is available by implementing this MODULE-COMPLIANCE." MODULE -- this module MANDATORY-GROUPS { mplsLdpGeneralGroup, mplsLdpNotificationsGroup } GROUP mplsLdpLspGroup DESCRIPTION "This group must be supported if the LSR MIB is implemented, specifically the mplsInSegmentTable, the mplsOutSegmentTable or the mplsXCTable." OBJECT mplsLdpEntityProtocolVersion MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityTcpPort MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityUdpDscPort MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityMaxPduLength MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityKeepAliveHoldTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityHelloHoldTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityInitSessionThreshold MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityLabelDistMethod MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityLabelRetentionMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityPathVectorLimit MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityHopCountLimit MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityTransportAddrKind MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityTargetPeer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityTargetPeerAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpEntityTargetPeerAddr SYNTAX InetAddress (SIZE(0|4|16)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpEntityLabelType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." OBJECT mplsFecType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsFecAddrPrefixLength MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsFecAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsFecAddr SYNTAX InetAddress (SIZE(0|4|16)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support IPv4 and globally unique IPv6 addresses." OBJECT mplsFecStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsFecRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." OBJECT mplsLdpLspFecStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpLspFecRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." OBJECT mplsLdpSessionPeerNextHopAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpSessionPeerNextHopAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation is only required to support IPv4 and globally unique IPv6 addresses." ::= { mplsLdpCompliances 2 } -- units of conformance mplsLdpGeneralGroup OBJECT-GROUP OBJECTS { mplsLdpLsrId, mplsLdpLsrLoopDetectionCapable, mplsLdpEntityLastChange, mplsLdpEntityIndexNext, mplsLdpEntityProtocolVersion, mplsLdpEntityAdminStatus, mplsLdpEntityOperStatus, mplsLdpEntityTcpPort, mplsLdpEntityUdpDscPort, mplsLdpEntityMaxPduLength, mplsLdpEntityKeepAliveHoldTimer, mplsLdpEntityHelloHoldTimer, mplsLdpEntityInitSessionThreshold, mplsLdpEntityLabelDistMethod, mplsLdpEntityLabelRetentionMode, mplsLdpEntityPathVectorLimit, mplsLdpEntityHopCountLimit, mplsLdpEntityTransportAddrKind, mplsLdpEntityTargetPeer, mplsLdpEntityTargetPeerAddrType, mplsLdpEntityTargetPeerAddr, mplsLdpEntityLabelType, mplsLdpEntityDiscontinuityTime, mplsLdpEntityStorageType, mplsLdpEntityRowStatus, mplsLdpEntityStatsSessionAttempts, mplsLdpEntityStatsSessionRejectedNoHelloErrors, mplsLdpEntityStatsSessionRejectedAdErrors, mplsLdpEntityStatsSessionRejectedMaxPduErrors, mplsLdpEntityStatsSessionRejectedLRErrors, mplsLdpEntityStatsBadLdpIdentifierErrors, mplsLdpEntityStatsBadPduLengthErrors, mplsLdpEntityStatsBadMessageLengthErrors, mplsLdpEntityStatsBadTlvLengthErrors, mplsLdpEntityStatsMalformedTlvValueErrors, mplsLdpEntityStatsKeepAliveTimerExpErrors, mplsLdpEntityStatsShutdownReceivedNotifications, mplsLdpEntityStatsShutdownSentNotifications, mplsLdpPeerLastChange, mplsLdpPeerLabelDistMethod, mplsLdpPeerPathVectorLimit, mplsLdpPeerTransportAddrType, mplsLdpPeerTransportAddr, mplsLdpHelloAdjacencyHoldTimeRem, mplsLdpHelloAdjacencyHoldTime, mplsLdpHelloAdjacencyType, mplsLdpSessionStateLastChange, mplsLdpSessionState, mplsLdpSessionRole, mplsLdpSessionProtocolVersion, mplsLdpSessionKeepAliveHoldTimeRem, mplsLdpSessionKeepAliveTime, mplsLdpSessionMaxPduLength, mplsLdpSessionDiscontinuityTime, mplsLdpSessionStatsUnknownMesTypeErrors, mplsLdpSessionStatsUnknownTlvErrors, mplsLdpSessionPeerNextHopAddrType, mplsLdpSessionPeerNextHopAddr, mplsFecLastChange, mplsFecIndexNext, mplsFecType, mplsFecAddrType, mplsFecAddr, mplsFecAddrPrefixLength, mplsFecStorageType, mplsFecRowStatus } STATUS current DESCRIPTION "Objects that apply to all MPLS LDP implementations." ::= { mplsLdpGroups 1 } mplsLdpLspGroup OBJECT-GROUP OBJECTS { mplsInSegmentLdpLspLabelType, mplsInSegmentLdpLspType, mplsOutSegmentLdpLspLabelType, mplsOutSegmentLdpLspType, mplsLdpLspFecLastChange, mplsLdpLspFecStorageType, mplsLdpLspFecRowStatus } STATUS current DESCRIPTION "These objects are for LDP implementations which interface to the Label Information Base (LIB) in the MPLS-LSR-STD-MIB. The LIB is represented in the mplsInSegmentTable, mplsOutSegmentTable and mplsXCTable." ::= { mplsLdpGroups 2 } mplsLdpNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { mplsLdpInitSessionThresholdExceeded, mplsLdpPathVectorLimitMismatch, mplsLdpSessionUp, mplsLdpSessionDown } STATUS current DESCRIPTION "The notification for an MPLS LDP implementation." ::= { mplsLdpGroups 3 } END