PMIPV6-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, mib-2, Integer32, Counter32, Gauge32, Unsigned32, OBJECT-TYPE, NOTIFICATION-TYPE FROM SNMPv2-SMI -- RFC 2578 PhysAddress, TimeStamp, TruthValue FROM SNMPv2-TC -- RFC 2579 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC 2580 InetAddressType, InetAddress, InetAddressPrefixLength FROM INET-ADDRESS-MIB -- RFC 4001 Ipv6AddressIfIdentifierTC FROM IP-MIB -- RFC 4293 mip6MnBLEntry, mip6BindingCacheEntry FROM MOBILEIPV6-MIB -- RFC 4295 Pmip6TimeStamp64, Pmip6MnIdentifier, Pmip6MnLLIdentifier, Pmip6MnIndex, Pmip6MnLLIndex, Pmip6MnInterfaceATT FROM PMIPV6-TC-MIB -- RFC 6475 ; pmip6MIB MODULE-IDENTITY LAST-UPDATED "201205070000Z" -- 7th May, 2012 ORGANIZATION "IETF NETLMM Working Group" CONTACT-INFO " Glenn Mansfield Keeni Postal: Cyber Solutions, Inc. 6-6-3, Minami Yoshinari Aoba-ku, Sendai 989-3204, Japan. Tel: +81-22-303-4012 Fax: +81-22-303-4015 EMail: [email protected] Kazuhide Koide Postal: KDDI Corporation GARDEN AIR TOWER 3-10-10, Iidabashi Chiyoda-ku, Tokyo 102-8460, Japan. Tel: +81-3-6678-3378 EMail: [email protected] Sri Gundavelli Postal: Cisco 170 W.Tasman Drive, San Jose, CA 95134 USA Tel: +1-408-527-6109 EMail: [email protected] Ryuji Wakikawa Postal: TOYOTA InfoTechnology Center, U.S.A., Inc. 465 Bernardo Avenue Mountain View, CA 94043 USA EMail: [email protected] Support Group EMail: [email protected]" DESCRIPTION "The MIB module for monitoring and controlling PMIPv6 entities. Copyright (c) 2012 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). " REVISION "201205070000Z" -- 7th May 2012 DESCRIPTION "Initial version, published as RFC 6475." ::= { mib-2 206 } -- The PMIPv6 MIB has the following 5 primary groups pmip6Notifications OBJECT IDENTIFIER ::= { pmip6MIB 0 } pmip6Objects OBJECT IDENTIFIER ::= { pmip6MIB 1 } pmip6Conformance OBJECT IDENTIFIER ::= { pmip6MIB 2 } pmip6Core OBJECT IDENTIFIER ::= { pmip6Objects 1 } pmip6Mag OBJECT IDENTIFIER ::= { pmip6Objects 2 } pmip6Lma OBJECT IDENTIFIER ::= { pmip6Objects 3 } -- The sub groups pmip6System OBJECT IDENTIFIER ::= { pmip6Core 1 } pmip6Bindings OBJECT IDENTIFIER ::= { pmip6Core 2 } pmip6Conf OBJECT IDENTIFIER ::= { pmip6Core 3 } pmip6Stats OBJECT IDENTIFIER ::= { pmip6Core 4 } pmip6MagSystem OBJECT IDENTIFIER ::= { pmip6Mag 1 } pmip6MagConf OBJECT IDENTIFIER ::= { pmip6Mag 2 } pmip6MagRegistration OBJECT IDENTIFIER ::= { pmip6Mag 3 } pmip6LmaSystem OBJECT IDENTIFIER ::= { pmip6Lma 1 } pmip6LmaConf OBJECT IDENTIFIER ::= { pmip6Lma 2 } -- The pmip6Stats group has the following sub groups pmip6BindingRegCounters OBJECT IDENTIFIER ::= { pmip6Stats 1 } -- -- -- pmip6System group -- -- pmip6Capabilities OBJECT-TYPE SYNTAX BITS { mobilityAccessGateway (0), localMobilityAnchor (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the PMIPv6 functions that are supported by this managed entity. Multiple Proxy Mobile IPv6 functions may be supported by a single entity. mobilityAccessGateway(0) indicates the availability of the mobility access gateway function. localMobilityAnchor(1) indicates the availability of the local mobility anchor function. " REFERENCE "RFC 6275: Sections 3.2, 4.1" ::= { pmip6System 1 } pmip6MobileNodeGeneratedTimestampInUse OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This flag indicates whether or not the MN-generated timestamp mechanism is in use in that Proxy Mobile IPv6 domain. true(1) indicates that the local mobility anchors and mobile access gateways in that Proxy Mobile IPv6 domain apply the MN-generated timestamp considerations. false(0) indicates that the MN-generated timestamp mechanism is not in use in that Proxy Mobile IPv6 domain. The default value for this flag is 'false'. " REFERENCE "RFC 5213: Sections 5.5, 9.3" DEFVAL { false } ::= { pmip6Conf 1 } pmip6FixedMagLinkLocalAddressOnAllAccessLinksType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The InetAddressType of the pmip6FixedMagLinkLocalAddressOnAllAccessLinks that follows. " ::= { pmip6Conf 2 } pmip6FixedMagLinkLocalAddressOnAllAccessLinks OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates the link-local address value that all the mobile access gateways should use on any of the access links shared with any of the mobile nodes in that Proxy Mobile IPv6 domain. If this variable is initialized with all zeroes, it implies that the use of fixed link-local address mode is not enabled for that Proxy Mobile IPv6 domain." REFERENCE "RFC 5213: Sections 2.2, 6.8, 6.9.1.1, 6.9.3, 9.3" ::= { pmip6Conf 3 } pmip6FixedMagLinkLayerAddressOnAllAccessLinks OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates the link-layer address value that all the mobile access gateways should use on any of the access links shared with any of the mobile nodes in that Proxy Mobile IPv6 domain. For access technologies where there is no link-layer address, this variable MUST be initialized with all zeroes. " REFERENCE "RFC 5213: Sections 6.9.3, 9.3" ::= { pmip6Conf 4 } pmip6MagStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the PMIPv6 mobile access gateway function is enabled for the managed entity. Changing the status from enabled(1) to disabled(2) will terminate the PMIPv6 mobile access gateway function. On the other hand, changing the status from disabled(2) to enabled(1) will start the PMIPv6 mobile access gateway function. The value of this object MUST remain unchanged across reboots of the managed entity. " DEFVAL { disabled } ::= { pmip6MagSystem 1 } pmip6MagProxyCOATable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6MagProxyCOAEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table models the Proxy Care-of Addresses configured on the egress interfaces of the mobile access gateway. This address is the transport endpoint of the tunnel between the local mobility anchor and the mobile access gateway. Entries in this table are not required to survive a reboot of the managed entity. " REFERENCE "RFC 5213: Sections 2.2, 6.10" ::= { pmip6MagSystem 2 } pmip6MagProxyCOAEntry OBJECT-TYPE SYNTAX Pmip6MagProxyCOAEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry represents a conceptual row in the Proxy-CoA table. It represents a Proxy Care-of Address on the mobile access gateway. Implementers need to be aware that if the total number of octets in pmip6MagProxyCOA exceeds 113, then OIDs of column instances in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3. " INDEX { pmip6MagProxyCOAType, pmip6MagProxyCOA } ::= { pmip6MagProxyCOATable 1 } Pmip6MagProxyCOAEntry ::= SEQUENCE { pmip6MagProxyCOAType InetAddressType, pmip6MagProxyCOA InetAddress, pmip6MagProxyCOAState INTEGER } pmip6MagProxyCOAType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The InetAddressType of the pmip6MagProxyCOA that follows. " ::= { pmip6MagProxyCOAEntry 1 } pmip6MagProxyCOA OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Proxy-CoA configured on the egress interface of the mobile access gateway. The type of the address represented by this object is specified by the corresponding pmip6MagProxyCOAType object. " REFERENCE "RFC 5213: Sections 2.2, 6.10" ::= { pmip6MagProxyCOAEntry 2 } pmip6MagProxyCOAState OBJECT-TYPE SYNTAX INTEGER { unknown(1), activated(2), tunneled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the state of the Proxy-CoA: unknown -- The state of the Proxy-CoA cannot be determined. activated -- The Proxy-CoA is ready to establish a tunnel. This state SHOULD be indicated when the MAG is up but has no mobile node. tunneled -- Bidirectional tunnel is established using the Proxy-CoA. " ::= { pmip6MagProxyCOAEntry 3 } pmip6MagEnableMagLocalRouting OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This flag indicates whether or not the mobile access gateway is allowed to enable local routing of the traffic exchanged between a visiting mobile node and a correspondent node that is locally connected to one of the interfaces of the mobile access gateway. The correspondent node can be another visiting mobile node as well, or a local fixed node. true(1) indicates that the mobile access gateway routes the traffic locally. false(0) indicates that the mobile access gateway reverse tunnels all the traffic to the mobile node's local mobility anchor. The default value for this flag is 'false'. " REFERENCE "RFC 5213: Section 9.2" DEFVAL { false } ::= { pmip6MagConf 1 } pmip6MagMnIdentifierTable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6MagMnIdentifierEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the identifiers of mobile nodes attached to the MAG. Entries in this table are not required to survive a reboot of the managed entity. " REFERENCE "RFC 5213: Sections 2.2, 6.1" ::= { pmip6MagConf 2 } pmip6MagMnIdentifierEntry OBJECT-TYPE SYNTAX Pmip6MagMnIdentifierEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the mobile node identifier table. " INDEX { pmip6MagBLMnIndex } ::= { pmip6MagMnIdentifierTable 1 } Pmip6MagMnIdentifierEntry ::= SEQUENCE { pmip6MagMnIdentifier Pmip6MnIdentifier } pmip6MagMnIdentifier OBJECT-TYPE SYNTAX Pmip6MnIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The identity of a mobile node in the Proxy Mobile IPv6 domain. " REFERENCE "RFC 5213: Sections 2.2, 6.1" ::= { pmip6MagMnIdentifierEntry 1 } pmip6MagMnLLIdentifierTable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6MagMnLLIdentifierEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the link-layer identifiers of the interfaces of the mobile nodes attached to the MAG. Entries in this table are not required to survive a reboot of the managed entity. " REFERENCE "RFC 5213: Sections 2.2, 6.1" ::= { pmip6MagConf 3 } pmip6MagMnLLIdentifierEntry OBJECT-TYPE SYNTAX Pmip6MagMnLLIdentifierEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the mobile node link-layer identifier table. " INDEX { pmip6MagBLMnIndex, pmip6MagBLMnLLIndex } ::= { pmip6MagMnLLIdentifierTable 1 } Pmip6MagMnLLIdentifierEntry ::= SEQUENCE { pmip6MagMnLLIdentifier Pmip6MnLLIdentifier } pmip6MagMnLLIdentifier OBJECT-TYPE SYNTAX Pmip6MnLLIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The link-layer identifier of the mobile node's connected interface on the access link. " REFERENCE "RFC 5213: Sections 2.2, 6.1" ::= { pmip6MagMnLLIdentifierEntry 1 } pmip6MagHomeNetworkPrefixTable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6MagHomeNetworkPrefixEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table representing the home network prefixes assigned to the connected interfaces of mobile nodes attached to the MAG. " REFERENCE "RFC 5213: Sections 2, 6.1, 6.2" ::= { pmip6MagConf 4 } pmip6MagHomeNetworkPrefixEntry OBJECT-TYPE SYNTAX Pmip6MagHomeNetworkPrefixEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the home network prefixes table. Implementers need to be aware that if the total number of octets in pmip6MagHomeNetworkPrefix exceeds 111, then OIDs of column instances in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3. " INDEX { pmip6MagBLMnIndex, pmip6MagBLMnLLIndex, pmip6MagHomeNetworkPrefixType, pmip6MagHomeNetworkPrefix } ::= { pmip6MagHomeNetworkPrefixTable 1 } Pmip6MagHomeNetworkPrefixEntry ::= SEQUENCE { pmip6MagHomeNetworkPrefixType InetAddressType, pmip6MagHomeNetworkPrefix InetAddress, pmip6MagHomeNetworkPrefixLength InetAddressPrefixLength, pmip6MagHomeNetworkPrefixLifeTime Unsigned32 } pmip6MagHomeNetworkPrefixType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The InetAddressType of the pmip6MagHomeNetworkPrefix that follows. " ::= { pmip6MagHomeNetworkPrefixEntry 1 } pmip6MagHomeNetworkPrefix OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mobile network prefix that is delegated to the mobile node. The type of the address represented by this object is specified by the corresponding pmip6MagHomeNetworkPrefixType object. " REFERENCE "RFC 5213: Section 2" ::= { pmip6MagHomeNetworkPrefixEntry 2 } pmip6MagHomeNetworkPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-only STATUS current DESCRIPTION "The prefix length of the home network prefix. " ::= { pmip6MagHomeNetworkPrefixEntry 3 } pmip6MagHomeNetworkPrefixLifeTime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The lifetime parameter (in seconds) that will be advertised in Router Advertisements by the MAG for this home network prefix. " REFERENCE "RFC 5213: Sections 6.2, 6.7" ::= { pmip6MagHomeNetworkPrefixEntry 4 } pmip6MagBLTable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6MagBLEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table corresponds to the Binding Update List (BL) that includes PMIPv6-related information and is maintained by the mobile access gateway. Entries from the table are deleted as the lifetime of the binding expires. " REFERENCE "RFC 6275: Sections 4.5, 11.1 RFC 5213: Section 6.1" ::= { pmip6MagRegistration 1 } pmip6MagBLEntry OBJECT-TYPE SYNTAX Pmip6MagBLEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing additional information from a Binding Update sent by the mobile access gateway to the local mobility anchor. " AUGMENTS {mip6MnBLEntry} ::= { pmip6MagBLTable 1 } Pmip6MagBLEntry ::= SEQUENCE { pmip6MagBLFlag TruthValue, pmip6MagBLMnIndex Pmip6MnIndex, pmip6MagBLMnLLIndex Pmip6MnLLIndex, pmip6MagBLMagLinkLocalAddressType InetAddressType, pmip6MagBLMagLinkLocalAddress InetAddress, pmip6MagBLMagIfIdentifierToMn Ipv6AddressIfIdentifierTC, pmip6MagBLTunnelIfIdentifier Ipv6AddressIfIdentifierTC, pmip6MagBLMnInterfaceATT Pmip6MnInterfaceATT, pmip6MagBLTimeRecentlyAccepted Pmip6TimeStamp64 } pmip6MagBLFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "true(1) indicates that the mobile access gateway sent the Proxy Binding Update with Proxy Registration Flag that indicates to the local mobility anchor that the registration is the Proxy Binding Update and is from a mobile access gateway. false(0) implies that the mobile access gateway is behaving as a simple mobile node. " REFERENCE "RFC 5213: Section 8.1" ::= { pmip6MagBLEntry 1 } pmip6MagBLMnIndex OBJECT-TYPE SYNTAX Pmip6MnIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index to the identifier of the attached mobile node in the pmip6MagMnIdentifierTable. " REFERENCE "RFC 5213: Sections 2.2, 6.1, 8.1" ::= { pmip6MagBLEntry 2 } pmip6MagBLMnLLIndex OBJECT-TYPE SYNTAX Pmip6MnLLIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index to the link-layer identifier of the mobile node's connected interface in the pmip6MagMnLLIdentifierTable. " REFERENCE "RFC 5213: Sections 2.2, 6.1, 8.1" ::= { pmip6MagBLEntry 3 } pmip6MagBLMagLinkLocalAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The InetAddressType of the pmip6MagBLMagLinkLocalAddress that follows. " ::= { pmip6MagBLEntry 4 } pmip6MagBLMagLinkLocalAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The link-local address of the mobile access gateway on the access link shared with the mobile node. This is the address that is present in the Link-local Address option of the corresponding Proxy Binding Update message. " REFERENCE "RFC 3963: Sections 4.1, 5.1" ::= { pmip6MagBLEntry 5 } pmip6MagBLMagIfIdentifierToMn OBJECT-TYPE SYNTAX Ipv6AddressIfIdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The interface identifier (if-id) of the point-to-point link between the mobile node and the mobile access gateway. This is internal to the mobile access gateway and is used to associate the Proxy Mobile IPv6 tunnel to the access link where the mobile node is attached. " REFERENCE "RFC 5213: Sections 6.1, 8.1" ::= { pmip6MagBLEntry 6 } pmip6MagBLTunnelIfIdentifier OBJECT-TYPE SYNTAX Ipv6AddressIfIdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The tunnel interface identifier (tunnel-if-id) of the bidirectional tunnel between the mobile node's local mobility anchor and the mobile access gateway. This is internal to the mobile access gateway. The tunnel interface identifier is acquired during the tunnel creation. " REFERENCE "RFC 5213: Sections 6.1, 8.1" ::= { pmip6MagBLEntry 7 } pmip6MagBLMnInterfaceATT OBJECT-TYPE SYNTAX Pmip6MnInterfaceATT MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the access technology by which the mobile node is currently attached to the mobile access gateway. " REFERENCE "RFC 5213: Sections 6.9.1.1, 6.9.1.5, 8.1" ::= { pmip6MagBLEntry 8 } pmip6MagBLTimeRecentlyAccepted OBJECT-TYPE SYNTAX Pmip6TimeStamp64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit timestamp value of the most recently accepted Proxy Binding Update message sent for this mobile node. This is the time of day on the mobile access gateway, when the Proxy Binding Acknowledgement message with the Status field set to 0 was received. If the Timestamp option is not present in the Proxy Binding Update message (i.e., when the sequence-number-based scheme is in use), the value MUST be initialized with all zeroes. " REFERENCE "RFC 5213: Sections 5.1, 8.1" ::= { pmip6MagBLEntry 9 } pmip6MagMnProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6MagMnProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table corresponds to the mobile node's policy profile that includes the essential operational parameters that are required by the network entities for managing the mobile node's mobility service. It contains policy profiles of mobile nodes that are connected to the mobile access gateway. Entries in this table are not required to survive a reboot of the managed entity. " REFERENCE "RFC 5213: Section 6.2" ::= { pmip6MagRegistration 2 } pmip6MagMnProfileEntry OBJECT-TYPE SYNTAX Pmip6MagMnProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information about the mobile node's policy profile. " INDEX { pmip6MagProfMnIndex } ::= { pmip6MagMnProfileTable 1 } Pmip6MagMnProfileEntry ::= SEQUENCE { pmip6MagProfMnIndex Pmip6MnIndex, pmip6MagProfMnIdentifier Pmip6MnIdentifier, pmip6MagProfMnLocalMobilityAnchorAddressType InetAddressType, pmip6MagProfMnLocalMobilityAnchorAddress InetAddress } pmip6MagProfMnIndex OBJECT-TYPE SYNTAX Pmip6MnIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for a mobile node in the Proxy Mobile IPv6 domain. " ::= { pmip6MagMnProfileEntry 1 } pmip6MagProfMnIdentifier OBJECT-TYPE SYNTAX Pmip6MnIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The identity of a mobile node in the Proxy Mobile IPv6 domain. " REFERENCE "RFC 5213: Section 2.2" ::= { pmip6MagMnProfileEntry 2 } pmip6MagProfMnLocalMobilityAnchorAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The InetAddressType of the pmip6MagMnLocalMobilityAnchorAddress that follows. " ::= { pmip6MagMnProfileEntry 3 } pmip6MagProfMnLocalMobilityAnchorAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The global address that is configured on the interface of the local mobility anchor and is the transport endpoint of the bidirectional tunnel established between the local mobility anchor and the mobile access gateway. This is the address to which the mobile access gateway sends the Proxy Binding Update messages. " REFERENCE "RFC 5213: Section 2.2" ::= { pmip6MagMnProfileEntry 4 } pmip6BindingCacheTable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6BindingCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table models the Binding Cache on the local mobility anchor. Entries from the table are deleted as the lifetime of the binding expires. Entries in this table are not required to survive a reboot of the managed entity. " REFERENCE "RFC 6275: Sections 4.5, 9.1, 10.1 RFC 5213: Section 5.1" ::= { pmip6Bindings 1 } pmip6BindingCacheEntry OBJECT-TYPE SYNTAX Pmip6BindingCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing additional information contained in the Binding Cache table of the local mobility anchor. " AUGMENTS {mip6BindingCacheEntry} ::= { pmip6BindingCacheTable 1 } Pmip6BindingCacheEntry ::= SEQUENCE { pmip6BindingPBUFlag TruthValue, pmip6BindingMnIndex Pmip6MnIndex, pmip6BindingMnLLIndex Pmip6MnLLIndex, pmip6BindingMagLinkLocalAddressType InetAddressType, pmip6BindingMagLinkLocalAddress InetAddress, pmip6BindingTunnelIfIdentifier Ipv6AddressIfIdentifierTC, pmip6BindingMnInterfaceATT Pmip6MnInterfaceATT, pmip6BindingTimeRecentlyAccepted Pmip6TimeStamp64 } pmip6BindingPBUFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "true(1) indicates that the local mobility anchor accepted the binding update with Proxy Registration Flag from a mobile access gateway. false(0) implies that the binding cache is from a mobile node. In this case, the remaining objects will not be accessible. " REFERENCE "RFC 5213: Sections 5.1, 8.1" ::= { pmip6BindingCacheEntry 1 } pmip6BindingMnIndex OBJECT-TYPE SYNTAX Pmip6MnIndex MAX-ACCESS read-only STATUS current DESCRIPTION "An index to the identifier of the registered mobile node. " REFERENCE "RFC 5213: Sections 2.2, 5.1, 8.1 RFC 4283: Section 3" ::= { pmip6BindingCacheEntry 2 } pmip6BindingMnLLIndex OBJECT-TYPE SYNTAX Pmip6MnLLIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index to the link-layer identifier of the mobile node's connected interface on the access link. " REFERENCE "RFC 5213: Sections 2.2, 5.1, 8.1" ::= { pmip6BindingCacheEntry 3 } pmip6BindingMagLinkLocalAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The InetAddressType of the pmip6BindingMagLinkLocalAddress that follows. " ::= { pmip6BindingCacheEntry 4 } pmip6BindingMagLinkLocalAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The link-local address of the mobile access gateway on the point-to-point link shared with the mobile node. This is generated by the local mobility anchor after accepting the initial Proxy Binding Update message. This is the address that is present in the Link-local Address option of the corresponding Proxy Binding Acknowledgement message. " REFERENCE "RFC 5213: Sections 5.1, 6.9.1.2, 8.2" ::= { pmip6BindingCacheEntry 5 } pmip6BindingTunnelIfIdentifier OBJECT-TYPE SYNTAX Ipv6AddressIfIdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The tunnel interface identifier (tunnel-if-id) of the bidirectional tunnel between the local mobility anchor and the mobile access gateway where the mobile node is currently anchored. This is internal to the local mobility anchor. The tunnel interface identifier is acquired during the tunnel creation. " REFERENCE "RFC 5213: Sections 5.1, 8.1" ::= { pmip6BindingCacheEntry 6 } pmip6BindingMnInterfaceATT OBJECT-TYPE SYNTAX Pmip6MnInterfaceATT MAX-ACCESS read-only STATUS current DESCRIPTION "The access technology type by which the mobile node is currently attached. This is obtained from the Access Technology Type option, present in the Proxy Binding Update message. " REFERENCE "RFC 5213: Sections 5.1, 8.1" ::= { pmip6BindingCacheEntry 7 } pmip6BindingTimeRecentlyAccepted OBJECT-TYPE SYNTAX Pmip6TimeStamp64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit timestamp value of the most recently accepted Proxy Binding Update message sent for this mobile node. This is the time of day on the local mobility anchor, when the message was received. If the Timestamp option is not present in the Proxy Binding Update message (i.e., when the sequence number based scheme is in use), the value MUST be initialized with all zeroes. " REFERENCE "RFC 5213: Sections 5.1, 8.1" ::= { pmip6BindingCacheEntry 8 } --- --- --- pmip6Stats group --- --- -- -- pmip6Stats:pmip6BindingRegCounters -- pmip6MissingMnIdentifierOption OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'Missing mobile node identifier option' (Code 160). Discontinuities in the value of this counter can occur at re-initialization of the mobile router, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.1, 8.9" ::= { pmip6BindingRegCounters 1 } pmip6MagNotAuthorizedForProxyReg OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'Not authorized to send Proxy Binding Updates' (Code 154). Discontinuities in the value of this counter can occur at re-initialization of the mobile router, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.1, 8.9" ::= { pmip6BindingRegCounters 2 } pmip6NotLMAForThisMobileNode OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'Not local mobility anchor for this mobile node' (Code 153). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.1, 8.9" ::= { pmip6BindingRegCounters 3 } pmip6ProxyRegNotEnabled OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'Proxy Registration not enabled' (Code 152). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.1, 6.9.1.2, 8.9" ::= { pmip6BindingRegCounters 4 } pmip6MissingHomeNetworkPrefixOption OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'Missing home network prefix option' (Code 158). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.1, 8.9" ::= { pmip6BindingRegCounters 5 } pmip6MissingHandOffIndicatorOption OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'Missing handoff indicator option' (Code 161). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.1, 8.9" ::= { pmip6BindingRegCounters 6 } pmip6MissingAccessTechTypeOption OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'Missing access technology type option' (Code 162). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.1, 8.9" ::= { pmip6BindingRegCounters 7 } pmip6NotAuthorizedForHomeNetworkPrefix OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'Mobile node not authorized for one or more of the requesting home network prefixes' (Code 155). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.2, 6.9.1.2, 8.9" ::= { pmip6BindingRegCounters 8 } pmip6TimestampMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'Invalid timestamp value (the clocks are out of sync)' (Code 156). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.5, 6.9.1.2, 8.9" ::= { pmip6BindingRegCounters 9 } pmip6TimestampLowerThanPrevAccepted OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'The timestamp value is lower than the previously accepted value' (Code 157). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.5, 6.9.1.2, 8.9" ::= { pmip6BindingRegCounters 10 } pmip6BcePbuPrefixSetDoNotMatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages rejected by the local mobility anchor with status code in the Binding Acknowledgement message indicating 'All the home network prefixes listed in the Binding Cache entry do not match all the prefixes in the received Proxy Binding Update' (Code 159). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.4.1.1, 8.9" ::= { pmip6BindingRegCounters 11 } pmip6InitialBindingRegistrations OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages that newly creates the Binding Cache entry. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.2" ::= { pmip6BindingRegCounters 12 } pmip6BindingLifeTimeExtensionNoHandOff OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages for extending the binding lifetime, received from the same mobile access gateway that last updated the binding. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.3" ::= { pmip6BindingRegCounters 13 } pmip6BindingLifeTimeExtensionAfterHandOff OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages for extending the binding lifetime, received from a new mobile access gateway where the mobile node's mobility session is handed off. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.4" ::= { pmip6BindingRegCounters 14 } pmip6BindingDeRegistrations OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Update messages with the lifetime value of zero. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.5" ::= { pmip6BindingRegCounters 15 } pmip6BindingBindingAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of Proxy Binding Acknowledgement messages. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of pmip6CounterDiscontinuityTime. " REFERENCE "RFC 5213: Sections 5.3.5" ::= { pmip6BindingRegCounters 16 } pmip6CounterDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this PMIPv6 entity's global counters, viz., counters with OID prefix 'pmip6BindingRegCounters' suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object will have a zero value. " ::= { pmip6BindingRegCounters 17 } pmip6LmaStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the PMIPv6 local mobility anchor function is enabled for the managed entity. Changing the status from enabled(1) to disabled(2) will terminate the PMIPv6 local mobility anchor function. On the other hand, changing the status from disabled(2) to enabled(1) will start the PMIPv6 local mobility anchor function. The value of this object MUST remain unchanged across reboots of the managed entity. " DEFVAL { disabled } ::= { pmip6LmaSystem 1 } pmip6LmaLMAATable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6LmaLMAAEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table models the LMA Addresses configured on the local mobility anchor. Each LMA Address acts as a transport endpoint of the tunnel between the local mobility anchor and the mobile access gateway and is the transport endpoint of the tunnel between the local mobility anchor and the mobile access gateway. Entries in this table are not required to survive a reboot of the managed entity. " REFERENCE "RFC 5213: Sections 2.2, 5.6" ::= { pmip6LmaSystem 2 } pmip6LmaLMAAEntry OBJECT-TYPE SYNTAX Pmip6LmaLMAAEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry represents a conceptual row in the LMAA table. It represents each LMAA on the local mobility anchor. Implementers need to be aware that if the total number of octets in pmip6LmaLMAA exceeds 113, then OIDs of column instances in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3. " INDEX { pmip6LmaLMAAType, pmip6LmaLMAA } ::= { pmip6LmaLMAATable 1 } Pmip6LmaLMAAEntry ::= SEQUENCE { pmip6LmaLMAAType InetAddressType, pmip6LmaLMAA InetAddress, pmip6LmaLMAAState INTEGER } pmip6LmaLMAAType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The InetAddressType of the pmip6LmaLMAA that follows. " ::= { pmip6LmaLMAAEntry 1 } pmip6LmaLMAA OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The LMAA configured on the local mobility anchor. The type of the address represented by this object is specified by the corresponding pmip6LmaLMAAType object. " REFERENCE "RFC 5213: Sections 2.2, 5.6" ::= { pmip6LmaLMAAEntry 2 } pmip6LmaLMAAState OBJECT-TYPE SYNTAX INTEGER { unknown(1), activated(2), tunneled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the state of the LMAA: unknown -- The state of the LMAA cannot be determined. activated -- The LMAA is ready to establish a tunnel. tunneled -- The LMAA is used to set up the bidirectional tunnel. " ::= { pmip6LmaLMAAEntry 3 } pmip6LmaMinDelayBeforeBCEDelete OBJECT-TYPE SYNTAX Integer32 (1..65535) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This variable specifies the length of time in milliseconds the local mobility anchor MUST wait before it deletes a Binding Cache entry of a mobile node, upon receiving a Proxy Binding Update message from a mobile access gateway with a lifetime value of 0. During this wait time, if the local mobility anchor receives a Proxy Binding Update for the same mobility binding, with a lifetime value greater than 0, then it must update the Binding Cache entry with the accepted binding values. By the end of this wait time, if the local mobility anchor did not receive any valid Proxy Binding Update message for that mobility binding, it MUST delete the Binding Cache entry. This delay essentially ensures that a mobile node's Binding Cache entry is not deleted too quickly and allows some time for the new mobile access gateway to complete the signaling for the mobile node. The default value for this variable is 10000 milliseconds. " REFERENCE "RFC 5213: Sections 5.3.5, 9.1" DEFVAL { 10000 } ::= { pmip6LmaConf 1 } pmip6LmaMaxDelayBeforeNewBCEAssign OBJECT-TYPE SYNTAX Integer32 (1..65535) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This variable specifies the length of time in milliseconds the local mobility anchor MUST wait for the de-registration message for an existing mobility session before it decides to create a new mobility session. The default value for this variable is 1500 milliseconds. Note that there is a dependency between this value and the values used in the retransmission algorithm for Proxy Binding Updates. The retransmissions need to happen before MaxDelayBeforeNewBCEAssign runs out, as otherwise there are situations where a de-registration from a previous mobile access gateway may be lost, and the local mobility anchor creates, needlessly, a new mobility session and new prefixes for the mobile node. However, this affects situations where there is no information from the lower layers about the type of a handoff or other parameters that can be used for identifying the mobility session. " REFERENCE "RFC 5213: Sections 5.4.1.2, 5.4.1.3, 9.1" DEFVAL { 1500 } ::= { pmip6LmaConf 2 } pmip6LmaTimestampValidityWindow OBJECT-TYPE SYNTAX Integer32 (1..65535) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This variable specifies the maximum length of time difference in milliseconds between the timestamp in the received Proxy Binding Update message and the current time of day on the local mobility anchor that is allowed by the local mobility anchor for the received message to be considered valid. The default value for this variable is 300 milliseconds. This variable must be adjusted to suit the deployments. " REFERENCE "RFC 5213: Sections 5.5, 9.1" DEFVAL { 300 } ::= { pmip6LmaConf 3 } pmip6LmaMnIdentifierTable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6LmaMnIdentifierEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the identifiers of mobile nodes served by the LMA. Entries in this table are not required to survive a reboot of the managed entity. " REFERENCE "RFC 5213: Sections 2, 6.1" ::= { pmip6LmaConf 4 } pmip6LmaMnIdentifierEntry OBJECT-TYPE SYNTAX Pmip6LmaMnIdentifierEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the mobile node identifier table. " INDEX { pmip6BindingMnIndex } ::= { pmip6LmaMnIdentifierTable 1 } Pmip6LmaMnIdentifierEntry ::= SEQUENCE { pmip6LmaMnIdentifier Pmip6MnIdentifier } pmip6LmaMnIdentifier OBJECT-TYPE SYNTAX Pmip6MnIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The identity of a mobile node in the Proxy Mobile IPv6 domain. " REFERENCE "RFC 5213: Section 2.2" ::= { pmip6LmaMnIdentifierEntry 1 } pmip6LmaMnLLIdentifierTable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6LmaMnLLIdentifierEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the link-layer identifiers of the interfaces of the mobile nodes served by the LMA. Entries in this table are not required to survive a reboot of the managed entity. " REFERENCE "RFC 5213: Sections 2, 6.1" ::= { pmip6LmaConf 5 } pmip6LmaMnLLIdentifierEntry OBJECT-TYPE SYNTAX Pmip6LmaMnLLIdentifierEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the mobile node link-layer identifier table. " INDEX { pmip6BindingMnIndex, pmip6BindingMnLLIndex } ::= { pmip6LmaMnLLIdentifierTable 1 } Pmip6LmaMnLLIdentifierEntry ::= SEQUENCE { pmip6LmaMnLLIdentifier Pmip6MnLLIdentifier } pmip6LmaMnLLIdentifier OBJECT-TYPE SYNTAX Pmip6MnLLIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The link-layer identifier of the mobile node's connected interface on the access link. " ::= { pmip6LmaMnLLIdentifierEntry 1 } pmip6LmaHomeNetworkPrefixTable OBJECT-TYPE SYNTAX SEQUENCE OF Pmip6LmaHomeNetworkPrefixEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table representing the home network prefixes assigned to the connected interfaces of all the mobile nodes anchored at the LMA. " REFERENCE "RFC 5213: Sections 2, 5.1, 5.2" ::= { pmip6LmaConf 6 } pmip6LmaHomeNetworkPrefixEntry OBJECT-TYPE SYNTAX Pmip6LmaHomeNetworkPrefixEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the home network prefixes table. Implementers need to be aware that if the total number of octets in pmip6LmaHomeNetworkPrefix exceeds 111 then OIDs of column instances in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3. " INDEX { pmip6BindingMnIndex, pmip6BindingMnLLIndex, pmip6LmaHomeNetworkPrefixType, pmip6LmaHomeNetworkPrefix } ::= { pmip6LmaHomeNetworkPrefixTable 1 } Pmip6LmaHomeNetworkPrefixEntry ::= SEQUENCE { pmip6LmaHomeNetworkPrefixType InetAddressType, pmip6LmaHomeNetworkPrefix InetAddress, pmip6LmaHomeNetworkPrefixLength InetAddressPrefixLength, pmip6LmaHomeNetworkPrefixLifeTime Gauge32 } pmip6LmaHomeNetworkPrefixType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The InetAddressType of the pmip6LmaHomeNetworkPrefix that follows. " ::= { pmip6LmaHomeNetworkPrefixEntry 1 } pmip6LmaHomeNetworkPrefix OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mobile network prefix that is delegated to the mobile node. The type of the address represented by this object is specified by the corresponding pmip6LmaHomeNetworkPrefixType object. " REFERENCE "RFC 5213: Section 2" ::= { pmip6LmaHomeNetworkPrefixEntry 2 } pmip6LmaHomeNetworkPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-only STATUS current DESCRIPTION "The prefix length of the home network prefix. " ::= { pmip6LmaHomeNetworkPrefixEntry 3 } pmip6LmaHomeNetworkPrefixLifeTime OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The lifetime (in seconds) granted to the mobile node for this registration. " REFERENCE "RFC 5213: Section 5.3" ::= { pmip6LmaHomeNetworkPrefixEntry 4 } -- -- pmip6Notifications -- -- pmip6MagHomeTunnelEstablished NOTIFICATION-TYPE OBJECTS { pmip6MagBLTunnelIfIdentifier, pmip6MagProxyCOAState } STATUS current DESCRIPTION "This notification is sent by the Proxy Mobile IPv6 entities every time the tunnel is established between the local mobility anchor and mobile access gateway. " REFERENCE "RFC 5213: Section 5.6.1" ::= { pmip6Notifications 1 } pmip6MagHomeTunnelReleased NOTIFICATION-TYPE OBJECTS { pmip6MagBLTunnelIfIdentifier, pmip6MagProxyCOAState } STATUS current DESCRIPTION "This notification is sent by the Proxy Mobile IPv6 entities every time the tunnel between the local mobility anchor and mobile access gateway is released. " REFERENCE "RFC 5213: Section 5.6.1" ::= { pmip6Notifications 2} pmip6LmaHomeTunnelEstablished NOTIFICATION-TYPE OBJECTS { pmip6BindingTunnelIfIdentifier, pmip6LmaLMAAState } STATUS current DESCRIPTION "This notification is sent by the Proxy Mobile IPv6 entities every time the tunnel is established between the local mobility anchor and mobile access gateway. " REFERENCE "RFC 5213: Section 5.6.1" ::= { pmip6Notifications 3 } pmip6LmaHomeTunnelReleased NOTIFICATION-TYPE OBJECTS { pmip6BindingTunnelIfIdentifier, pmip6LmaLMAAState } STATUS current DESCRIPTION "This notification is sent by the Proxy Mobile IPv6 entities every time the tunnel between the local mobility anchor and mobile access gateway is released. " REFERENCE "RFC 5213: Section 5.6.1" ::= { pmip6Notifications 4} -- Conformance information pmip6Groups OBJECT IDENTIFIER ::= { pmip6Conformance 1 } pmip6Compliances OBJECT IDENTIFIER ::= { pmip6Conformance 2 } -- Units of conformance pmip6SystemGroup OBJECT-GROUP OBJECTS { pmip6Capabilities, pmip6MobileNodeGeneratedTimestampInUse, pmip6FixedMagLinkLocalAddressOnAllAccessLinksType, pmip6FixedMagLinkLocalAddressOnAllAccessLinks, pmip6FixedMagLinkLayerAddressOnAllAccessLinks } STATUS current DESCRIPTION " A collection of objects for basic PMIPv6 monitoring." ::= { pmip6Groups 1 } pmip6BindingCacheGroup OBJECT-GROUP OBJECTS { pmip6BindingPBUFlag, pmip6BindingMnIndex, pmip6BindingMnLLIndex, pmip6BindingMagLinkLocalAddressType, pmip6BindingMagLinkLocalAddress, pmip6BindingTunnelIfIdentifier, pmip6BindingMnInterfaceATT, pmip6BindingTimeRecentlyAccepted, pmip6LmaMnIdentifier, pmip6LmaMnLLIdentifier } STATUS current DESCRIPTION " A collection of objects for monitoring the PMIPv6 extensions of the Binding Cache." ::= { pmip6Groups 2 } pmip6StatsGroup OBJECT-GROUP OBJECTS { pmip6MissingMnIdentifierOption, pmip6MagNotAuthorizedForProxyReg, pmip6NotLMAForThisMobileNode, pmip6ProxyRegNotEnabled, pmip6MissingHomeNetworkPrefixOption, pmip6MissingHandOffIndicatorOption, pmip6MissingAccessTechTypeOption, pmip6NotAuthorizedForHomeNetworkPrefix, pmip6TimestampMismatch, pmip6TimestampLowerThanPrevAccepted, pmip6BcePbuPrefixSetDoNotMatch, pmip6InitialBindingRegistrations, pmip6BindingLifeTimeExtensionNoHandOff, pmip6BindingLifeTimeExtensionAfterHandOff, pmip6BindingDeRegistrations, pmip6BindingBindingAcks, pmip6CounterDiscontinuityTime } STATUS current DESCRIPTION " A collection of objects for basic PMIPv6 statistics monitoring. " ::= { pmip6Groups 3 } pmip6MagSystemGroup OBJECT-GROUP OBJECTS { pmip6MagStatus, pmip6MagProxyCOAState } STATUS current DESCRIPTION " A collection of objects for monitoring the PMIPv6-system-related objects on a mobile router." ::= { pmip6Groups 4 } pmip6MagConfigurationGroup OBJECT-GROUP OBJECTS { pmip6MagHomeNetworkPrefixLength, pmip6MagHomeNetworkPrefixLifeTime, pmip6MagEnableMagLocalRouting } STATUS current DESCRIPTION " A collection of objects for monitoring the configuration-related objects on a mobile access gateway. " ::= { pmip6Groups 5 } pmip6MagRegistrationGroup OBJECT-GROUP OBJECTS { pmip6MagBLFlag, pmip6MagBLMnIndex, pmip6MagBLMnLLIndex, pmip6MagBLMagLinkLocalAddressType, pmip6MagBLMagLinkLocalAddress, pmip6MagBLMagIfIdentifierToMn, pmip6MagBLTunnelIfIdentifier, pmip6MagBLMnInterfaceATT, pmip6MagBLTimeRecentlyAccepted, pmip6MagMnIdentifier, pmip6MagMnLLIdentifier, pmip6MagProfMnIdentifier, pmip6MagProfMnLocalMobilityAnchorAddressType, pmip6MagProfMnLocalMobilityAnchorAddress } STATUS current DESCRIPTION " A collection of objects for monitoring the registration-related objects on a mobile access gateway. " ::= { pmip6Groups 6 } pmip6LmaSystemGroup OBJECT-GROUP OBJECTS { pmip6LmaStatus, pmip6LmaLMAAState } STATUS current DESCRIPTION " A collection of objects for monitoring the system-related objects on an LMA." ::= { pmip6Groups 7 } pmip6LmaConfigurationGroup OBJECT-GROUP OBJECTS { pmip6LmaMinDelayBeforeBCEDelete, pmip6LmaMaxDelayBeforeNewBCEAssign, pmip6LmaTimestampValidityWindow, pmip6LmaHomeNetworkPrefixLength, pmip6LmaHomeNetworkPrefixLifeTime } STATUS current DESCRIPTION " A collection of objects for Monitoring the configuration-related objects on an LMA." ::= { pmip6Groups 8 } pmip6MagNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { pmip6MagHomeTunnelEstablished, pmip6MagHomeTunnelReleased } STATUS current DESCRIPTION "A collection of notifications from a home agent or correspondent node to the Manager about the tunnel status of the mobile router. " ::= { pmip6Groups 9 } pmip6LmaNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { pmip6LmaHomeTunnelEstablished, pmip6LmaHomeTunnelReleased } STATUS current DESCRIPTION "A collection of notifications from a home agent or correspondent node to the Manager about the tunnel status of the mobile router. " ::= { pmip6Groups 10 } -- Compliance statements pmip6CoreCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB. There are a number of INDEX objects that cannot be represented in the form of OBJECT clauses in SMIv2, but for which there are compliance requirements, expressed in OBJECT clause form in this description: -- OBJECT pmip6BindingHomeAddressType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- ipv6 addresses for the pmip6BindingHomeAddress -- object. -- " MODULE -- this module MANDATORY-GROUPS { pmip6SystemGroup } ::= { pmip6Compliances 1 } pmip6Compliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB. " MODULE -- this module MANDATORY-GROUPS { pmip6SystemGroup, pmip6BindingCacheGroup, pmip6StatsGroup } ::= { pmip6Compliances 2 } pmip6CoreReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB without support for read-write (i.e., in read-only mode). " MODULE -- this module MANDATORY-GROUPS { pmip6SystemGroup } OBJECT pmip6MobileNodeGeneratedTimestampInUse MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6FixedMagLinkLocalAddressOnAllAccessLinksType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6FixedMagLinkLocalAddressOnAllAccessLinks MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6FixedMagLinkLayerAddressOnAllAccessLinks MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pmip6Compliances 3 } pmip6ReadOnlyCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB without support for read-write (i.e., in read-only mode). " MODULE -- this module MANDATORY-GROUPS { pmip6SystemGroup, pmip6BindingCacheGroup, pmip6StatsGroup } OBJECT pmip6MobileNodeGeneratedTimestampInUse MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6FixedMagLinkLocalAddressOnAllAccessLinksType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6FixedMagLinkLocalAddressOnAllAccessLinks MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6FixedMagLinkLayerAddressOnAllAccessLinks MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pmip6Compliances 4 } pmip6MagCoreCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB. There are a number of INDEX objects that cannot be represented in the form of OBJECT clauses in SMIv2, but for which there are compliance requirements, expressed in OBJECT clause form in this description: -- OBJECT pmip6MagProxyCOAType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6MagProxyCOAType -- object. -- -- OBJECT pmip6MagProxyCOA -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6MagProxyCOA -- object. -- " MODULE -- this module MANDATORY-GROUPS { pmip6MagSystemGroup } ::= { pmip6Compliances 5 } pmip6MagCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB for monitoring configuration- related information, registration details, and statistics on a mobile access gateway. There are a number of INDEX objects that cannot be represented in the form of OBJECT clauses in SMIv2, but for which there are compliance requirements, expressed in OBJECT clause form in this description: -- OBJECT pmip6MagProxyCOAType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6MagProxyCOA -- object. -- -- OBJECT pmip6MagProxyCOA -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6MagProxyCOAType -- object. -- -- OBJECT pmip6MagHomeNetworkPrefixType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the -- pmip6MagHomeNetworkPrefix object. -- -- OBJECT pmip6MagHomeNetworkPrefix -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the -- pmip6MagHomeNetworkPrefix object. -- " MODULE -- this module MANDATORY-GROUPS { pmip6MagSystemGroup, pmip6MagConfigurationGroup, pmip6MagRegistrationGroup } ::= { pmip6Compliances 6 } pmip6MagCoreReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB without support for read-write (i.e., in read-only mode). There are a number of INDEX objects that cannot be represented in the form of OBJECT clauses in SMIv2, but for which there are compliance requirements, expressed in OBJECT clause form in this description: -- OBJECT pmip6MagProxyCOAType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6MagProxyCOA -- object. -- -- OBJECT pmip6MagProxyCOA -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6MagProxyCOAType -- object. -- -- OBJECT pmip6MagHomeNetworkPrefixType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the -- pmip6MagHomeNetworkPrefix object. -- " MODULE -- this module MANDATORY-GROUPS { pmip6MagSystemGroup } OBJECT pmip6MagStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pmip6Compliances 7 } pmip6MagReadOnlyCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB without support for read- write (i.e., in read-only mode) and with support for monitoring configuration-related information, registration details, and statistics on a mobile access gateway. There are a number of INDEX objects that cannot be represented in the form of OBJECT clauses in SMIv2, but for which there are compliance requirements, expressed in OBJECT clause form in this description: -- OBJECT pmip6MagProxyCOAType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6MagProxyCOA -- object. -- -- OBJECT pmip6MagProxyCOA -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6MagProxyCOAType -- object. -- -- OBJECT pmip6MagHomeNetworkPrefixType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the -- pmip6MagHomeNetworkPrefix object. -- -- OBJECT pmip6MagHomeNetworkPrefix -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the -- pmip6MagHomeNetworkPrefix object. -- " MODULE -- this module MANDATORY-GROUPS { pmip6MagSystemGroup, pmip6MagConfigurationGroup, pmip6MagRegistrationGroup } OBJECT pmip6MagStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6MagEnableMagLocalRouting MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pmip6Compliances 8 } pmip6LmaCoreCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB. There are a number of INDEX objects that cannot be represented in the form of OBJECT clauses in SMIv2, but for which there are compliance requirements, expressed in OBJECT clause form in this description: -- OBJECT pmip6LmaLMAAType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6LmaLMAA -- object. -- -- OBJECT pmip6LmaLMAA -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6LmaLMAA -- object. -- " MODULE -- this module MANDATORY-GROUPS { pmip6LmaSystemGroup } ::= { pmip6Compliances 9 } pmip6LmaCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB for monitoring configuration- related information, registration details, and statistics on a mobile access gateway. There are a number of INDEX objects that cannot be represented in the form of OBJECT clauses in SMIv2, but for which there are compliance requirements, expressed in OBJECT clause form in this description: -- OBJECT pmip6LmaLMAAType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6LmaLMAA -- object. -- -- OBJECT pmip6LmaLMAA -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6LmaLMAA -- object. -- -- OBJECT pmip6LmaHomeNetworkPrefixType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the -- pmip6LmaHomeNetworkPrefix object. -- -- OBJECT pmip6LmaHomeNetworkPrefix -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the -- pmip6LmaHomeNetworkPrefix object. -- " MODULE -- this module MANDATORY-GROUPS { pmip6LmaSystemGroup, pmip6LmaConfigurationGroup } ::= { pmip6Compliances 10 } pmip6LmaReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB. There are a number of INDEX objects that cannot be represented in the form of OBJECT clauses in SMIv2, but for which there are compliance requirements, expressed in OBJECT clause form in this description: -- OBJECT pmip6LmaLMAAType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6LmaLMAA -- object. -- -- OBJECT pmip6LmaLMAA -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6LmaLMAA -- object. -- " MODULE -- this module MANDATORY-GROUPS { pmip6LmaSystemGroup } OBJECT pmip6LmaStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pmip6Compliances 11 } pmip6LmaReadOnlyCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB without support for read-write (i.e., in read-only mode) and for monitoring configuration-related information, registration details, and statistics on a mobile access gateway. There are a number of INDEX objects that cannot be represented in the form of OBJECT clauses in SMIv2, but for which there are compliance requirements, expressed in OBJECT clause form in this description: -- OBJECT pmip6LmaLMAAType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6LmaLMAA -- object. -- -- OBJECT pmip6LmaLMAA -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the pmip6LmaLMAA -- object. -- -- OBJECT pmip6LmaHomeNetworkPrefixType -- SYNTAX InetAddressType { ipv6(2) } -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the -- pmip6LmaHomeNetworkPrefix object. -- -- OBJECT pmip6LmaHomeNetworkPrefix -- SYNTAX InetAddress (SIZE(16)) -- DESCRIPTION -- This MIB module requires support for global -- IPv6 addresses for the -- pmip6LmaHomeNetworkPrefix object. -- " MODULE -- this module MANDATORY-GROUPS { pmip6LmaSystemGroup, pmip6LmaConfigurationGroup } OBJECT pmip6LmaStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6LmaMinDelayBeforeBCEDelete MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6LmaMaxDelayBeforeNewBCEAssign MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6LmaTimestampValidityWindow MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pmip6LmaHomeNetworkPrefixLifeTime MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pmip6Compliances 12 } pmip6MagNotificationCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB and support notification from the mobile access gateway. " MODULE -- this module MANDATORY-GROUPS { pmip6MagNotificationGroup } ::= { pmip6Compliances 13 } pmip6LmaNotificationCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement the PMIPV6-MIB and support notification from the LMA. " MODULE -- this module MANDATORY-GROUPS { pmip6LmaNotificationGroup } ::={ pmip6Compliances 14 } END