POLICY-BASED-MANAGEMENT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Gauge32, Unsigned32, mib-2 FROM SNMPv2-SMI RowStatus, RowPointer, TEXTUAL-CONVENTION, DateAndTime, StorageType FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB; -- Policy-Based Management MIB pmMib MODULE-IDENTITY LAST-UPDATED "200502070000Z" -- February 7, 2005 ORGANIZATION "IETF SNMP Configuration Working Group" CONTACT-INFO " Steve Waldbusser Phone: +1-650-948-6500 Fax: +1-650-745-0671 Email: [email protected] Jon Saperia (WG Co-chair) JDS Consulting, Inc. 84 Kettell Plain Road. Stow MA 01775 USA Phone: +1-978-461-0249 Fax: +1-617-249-0874 Email: [email protected] Thippanna Hongal Riverstone Networks, Inc. 5200 Great America Parkway Santa Clara, CA, 95054 USA Phone: +1-408-878-6562 Fax: +1-408-878-6501 Email: [email protected] David Partain (WG Co-chair) Postal: Ericsson AB P.O. Box 1248 SE-581 12 Linkoping Sweden Tel: +46 13 28 41 44 E-mail: [email protected] Any questions or comments about this document can also be directed to the working group at [email protected]." DESCRIPTION "The MIB module for policy-based configuration of SNMP infrastructures. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 4011; see the RFC itself for full legal notices." REVISION "200502070000Z" -- February 7, 2005 DESCRIPTION "The original version of this MIB, published as RFC4011." ::= { mib-2 124 } PmUTF8String ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An octet string containing information typically in human-readable form. To facilitate internationalization, this information is represented by using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in RFC 3629. As additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x10FFFF. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or that are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character/code point; thus, the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by RFC 3416. Note that the size of PmUTF8String object is measured in octets, not characters." SYNTAX OCTET STRING (SIZE (0..65535)) -- The policy table pmPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF PmPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The policy table. A policy is a pairing of a policyCondition and a policyAction that is used to apply the action to a selected set of elements." ::= { pmMib 1 } pmPolicyEntry OBJECT-TYPE SYNTAX PmPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the policy table representing one policy." INDEX { pmPolicyAdminGroup, pmPolicyIndex } ::= { pmPolicyTable 1 } PmPolicyEntry ::= SEQUENCE { pmPolicyAdminGroup PmUTF8String, pmPolicyIndex Unsigned32, pmPolicyPrecedenceGroup PmUTF8String, pmPolicyPrecedence Unsigned32, pmPolicySchedule Unsigned32, pmPolicyElementTypeFilter PmUTF8String, pmPolicyConditionScriptIndex Unsigned32, pmPolicyActionScriptIndex Unsigned32, pmPolicyParameters OCTET STRING, pmPolicyConditionMaxLatency Unsigned32, pmPolicyActionMaxLatency Unsigned32, pmPolicyMaxIterations Unsigned32, pmPolicyDescription PmUTF8String, pmPolicyMatches Gauge32, pmPolicyAbnormalTerminations Gauge32, pmPolicyExecutionErrors Counter32, pmPolicyDebugging INTEGER, pmPolicyAdminStatus INTEGER, pmPolicyStorageType StorageType, pmPolicyRowStatus RowStatus } pmPolicyAdminGroup OBJECT-TYPE SYNTAX PmUTF8String (SIZE(0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An administratively assigned string that can be used to group policies for convenience, for readability, or to simplify configuration of access control. The value of this string does not affect policy processing in any way. If grouping is not desired or necessary, this object may be set to a zero-length string." ::= { pmPolicyEntry 1 } pmPolicyIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique index for this policy entry, unique among all policies regardless of administrative group." ::= { pmPolicyEntry 2 } pmPolicyPrecedenceGroup OBJECT-TYPE SYNTAX PmUTF8String (SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "An administratively assigned string that is used to group policies. For each element, only one policy in the same precedence group may be active on that element. If multiple policies would be active on an element (because their conditions return non-zero), the execution environment will only allow the policy with the highest value of pmPolicyPrecedence to be active. All values of this object must have been successfully transformed by Stringprep RFC 3454. Management stations must perform this translation and must only set this object to string values that have been transformed." ::= { pmPolicyEntry 3 } pmPolicyPrecedence OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "If, while checking to see which policy conditions match an element, 2 or more ready policies in the same precedence group match the same element, the pmPolicyPrecedence object provides the rule to arbitrate which single policy will be active on 'this element'. Of policies in the same precedence group, only the ready and matching policy with the highest precedence value (e.g., 2 is higher than 1) will have its policy action periodically executed on 'this element'. When a policy is active on an element but the condition ceases to match the element, its action (if currently running) will be allowed to finish and then the condition-matching ready policy with the next-highest precedence will immediately become active (and have its action run immediately). If the condition of a higher-precedence ready policy suddenly begins matching an element, the previously-active policy's action (if currently running) will be allowed to finish and then the higher precedence policy will immediately become active. Its action will run immediately, and any lower-precedence matching policy will not be active anymore. In the case where multiple ready policies share the highest value, it is an implementation-dependent matter as to which single policy action will be chosen. Note that if it is necessary to take certain actions after a policy is no longer active on an element, these actions should be included in a lower-precedence policy that is in the same precedence group." ::= { pmPolicyEntry 4 } pmPolicySchedule OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "This policy will be ready if any of the associated schedule entries are active. If the value of this object is 0, this policy is always ready. If the value of this object is non-zero but doesn't refer to a schedule group that includes an active schedule, then the policy will not be ready, even if this is due to a misconfiguration of this object or the pmSchedTable." ::= { pmPolicyEntry 5 } pmPolicyElementTypeFilter OBJECT-TYPE SYNTAX PmUTF8String (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the element types for which this policy can be executed. The format of this object will be a sequence of pmElementTypeRegOIDPrefix values, encoded in the following BNF form: elementTypeFilter: oid [ ';' oid ]* oid: subid [ '.' subid ]* subid: '0' | decimal_constant For example, to register for the policy to be run on all interface elements, the 'ifEntry' element type will be registered as '1.3.6.1.2.1.2.2.1'. If a value is included that does not represent a registered pmElementTypeRegOIDPrefix, then that value will be ignored." ::= { pmPolicyEntry 6 } pmPolicyConditionScriptIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the row or rows in the pmPolicyCodeTable that contain the condition code for this policy. When a policy entry is created, a pmPolicyCodeIndex value unused by this policy's adminGroup will be assigned to this object. A policy condition is one or more PolicyScript statements that result(s) in a boolean value that represents whether an element is a member of a set of elements upon which an action is to be performed. If a policy is ready and the condition returns true for an element of a proper element type, and if no higher-precedence policy should be active, then the policy is active on that element. Condition evaluation stops immediately when any run-time exception is detected, and the policyAction is not executed. The policyCondition is evaluated for various elements. Any element for which the policyCondition returns any nonzero value will match the condition and will have the associated policyAction executed on that element unless a higher-precedence policy in the same precedence group also matches 'this element'. If the condition object is empty (contains no code) or otherwise does not return a value, the element will not be matched. When this condition is executed, if SNMP requests are made to the local system and secModel/secName/secLevel aren't specified, access to objects is under the security credentials of the requester who most recently modified the associated pmPolicyAdminStatus object. If SNMP requests are made in which secModel/secName/secLevel are specified, then the specified credentials are retrieved from the local configuration datastore only if VACM is configured to allow access to the requester who most recently modified the associated pmPolicyAdminStatus object. See the Security Considerations section for more information." ::= { pmPolicyEntry 7 } pmPolicyActionScriptIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the row or rows in the pmPolicyCodeTable that contain the action code for this policy. When a policy entry is created, a pmPolicyCodeIndex value unused by this policy's adminGroup will be assigned to this object. A PolicyAction is an operation performed on a set of elements for which the policy is active. Action evaluation stops immediately when any run-time exception is detected. When this condition is executed, if SNMP requests are made to the local system and secModel/secName/secLevel aren't specified, access to objects is under the security credentials of the requester who most recently modified the associated pmPolicyAdminStatus object. If SNMP requests are made in which secModel/secName/secLevel are specified, then the specified credentials are retrieved from the local configuration datastore only if VACM is configured to allow access to the requester who most recently modified the associated pmPolicyAdminStatus object. See the Security Considerations section for more information." ::= { pmPolicyEntry 8 } pmPolicyParameters OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..65535)) MAX-ACCESS read-create STATUS current DESCRIPTION "From time to time, policy scripts may seek one or more parameters (e.g., site-specific constants). These parameters may be installed with the script in this object and are accessible to the script via the getParameters() function. If it is necessary for multiple parameters to be passed to the script, the script can choose whatever encoding/delimiting mechanism is most appropriate." ::= { pmPolicyEntry 9 } pmPolicyConditionMaxLatency OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Every element under the control of this agent is re-checked periodically to see whether it is under control of this policy by re-running the condition for this policy. This object lets the manager control the maximum amount of time that may pass before an element is re-checked. In other words, in any given interval of this duration, all elements must be re-checked. Note that how the policy agent schedules the checking of various elements within this interval is an implementation-dependent matter. Implementations may wish to re-run a condition more quickly if they note a change to the role strings for an element." ::= { pmPolicyEntry 10 } pmPolicyActionMaxLatency OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Every element that matches this policy's condition and is therefore under control of this policy will have this policy's action executed periodically to ensure that the element remains in the state dictated by the policy. This object lets the manager control the maximum amount of time that may pass before an element has the action run on it. In other words, in any given interval of this duration, all elements under control of this policy must have the action run on them. Note that how the policy agent schedules the policy action on various elements within this interval is an implementation-dependent matter." ::= { pmPolicyEntry 11 } pmPolicyMaxIterations OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "If a condition or action script iterates in loops too many times in one invocation, the execution environment may consider it in an infinite loop or otherwise not acting as intended and may be terminated by the execution environment. The execution environment will count the cumulative number of times all 'for' or 'while' loops iterated and will apply a threshold to determine when to terminate the script. What threshold the execution environment uses is an implementation-dependent manner, but the value of this object SHOULD be the basis for choosing the threshold for each script. The value of this object represents a policy-specific threshold and can be tuned for policies of varying workloads. If this value is zero, no threshold will be enforced except for any implementation-dependent maximum. Regardless of this value, the agent is allowed to terminate any script invocation that exceeds a local CPU or memory limitation. Note that the condition and action invocations are tracked separately." ::= { pmPolicyEntry 12 } pmPolicyDescription OBJECT-TYPE SYNTAX PmUTF8String MAX-ACCESS read-create STATUS current DESCRIPTION "A description of this rule and its significance, typically provided by a human." ::= { pmPolicyEntry 13 } pmPolicyMatches OBJECT-TYPE SYNTAX Gauge32 UNITS "elements" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of elements that, in their most recent execution of the associated condition, were matched by the condition." ::= { pmPolicyEntry 14 } pmPolicyAbnormalTerminations OBJECT-TYPE SYNTAX Gauge32 UNITS "elements" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of elements that, in their most recent execution of the associated condition or action, have experienced a run-time exception and terminated abnormally. Note that if a policy was experiencing a run-time exception while processing a particular element but runs normally on a subsequent invocation, this number can decline." ::= { pmPolicyEntry 15 } pmPolicyExecutionErrors OBJECT-TYPE SYNTAX Counter32 UNITS "errors" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times that execution of this policy's condition or action has been terminated due to run-time exceptions." ::= { pmPolicyEntry 16 } pmPolicyDebugging OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The status of debugging for this policy. If this is turned on(2), log entries will be created in the pmDebuggingTable for each run-time exception that is experienced by this policy." DEFVAL { off } ::= { pmPolicyEntry 17 } pmPolicyAdminStatus OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), enabledAutoRemove(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative status of this policy. The policy will be valid only if the associated pmPolicyRowStatus is set to active(1) and this object is set to enabled(2) or enabledAutoRemove(3). If this object is set to enabledAutoRemove(3), the next time the associated schedule moves from the active state to the inactive state, this policy will immediately be deleted, including any associated entries in the pmPolicyCodeTable. The following related objects may not be changed unless this object is set to disabled(1): pmPolicyPrecedenceGroup, pmPolicyPrecedence, pmPolicySchedule, pmPolicyElementTypeFilter, pmPolicyConditionScriptIndex, pmPolicyActionScriptIndex, pmPolicyParameters, and any pmPolicyCodeTable row referenced by this policy. In order to change any of these parameters, the policy must be moved to the disabled(1) state, changed, and then re-enabled. When this policy moves to either enabled state from the disabled state, any cached values of policy condition must be erased, and any Policy or PolicyElement scratchpad values for this policy should be removed. Policy execution will begin by testing the policy condition on all appropriate elements." ::= { pmPolicyEntry 18 } pmPolicyStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This object defines whether this policy and any associated entries in the pmPolicyCodeTable are kept in volatile storage and lost upon reboot or if this row is backed up by non-volatile or permanent storage. If the value of this object is 'permanent', the values for the associated pmPolicyAdminStatus object must remain writable." ::= { pmPolicyEntry 19 } pmPolicyRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of this pmPolicyEntry. The status may not be set to active if any of the related entries in the pmPolicyCode table do not have a status of active or if any of the objects in this row are not set to valid values. Only the following objects may be modified while in the active state: pmPolicyParameters pmPolicyConditionMaxLatency pmPolicyActionMaxLatency pmPolicyDebugging pmPolicyAdminStatus If this row is deleted, any associated entries in the pmPolicyCodeTable will be deleted as well." ::= { pmPolicyEntry 20 } -- Policy Code Table pmPolicyCodeTable OBJECT-TYPE SYNTAX SEQUENCE OF PmPolicyCodeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The pmPolicyCodeTable stores the code for policy conditions and actions. An example of the relationships between the code table and the policy table follows: pmPolicyTable AdminGroup Index ConditionScriptIndex ActionScriptIndex A '' 1 1 2 B 'oper' 1 1 2 C 'oper' 2 3 4 pmPolicyCodeTable AdminGroup ScriptIndex Segment Note '' 1 1 Filter for policy A '' 2 1 Action for policy A 'oper' 1 1 Filter for policy B 'oper' 2 1 Action 1/2 for policy B 'oper' 2 2 Action 2/2 for policy B 'oper' 3 1 Filter for policy C 'oper' 4 1 Action for policy C In this example, there are 3 policies: 1 in the '' adminGroup, and 2 in the 'oper' adminGroup. Policy A has been assigned script indexes 1 and 2 (these script indexes are assigned out of a separate pool per adminGroup), with 1 code segment each for the filter and the action. Policy B has been assigned script indexes 1 and 2 (out of the pool for the 'oper' adminGroup). While the filter has 1 segment, the action is longer and is loaded into 2 segments. Finally, Policy C has been assigned script indexes 3 and 4, with 1 code segment each for the filter and the action." ::= { pmMib 2 } pmPolicyCodeEntry OBJECT-TYPE SYNTAX PmPolicyCodeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the policy code table representing one code segment. Entries that share a common AdminGroup/ScriptIndex pair make up a single script. Valid values of ScriptIndex are retrieved from pmPolicyConditionScriptIndex and pmPolicyActionScriptIndex after a pmPolicyEntry is created. Segments of code can then be written to this table with the learned ScriptIndex values. The StorageType of this entry is determined by the value of the associated pmPolicyStorageType. The pmPolicyAdminGroup element of the index represents the administrative group of the policy of which this code entry is a part." INDEX { pmPolicyAdminGroup, pmPolicyCodeScriptIndex, pmPolicyCodeSegment } ::= { pmPolicyCodeTable 1 } PmPolicyCodeEntry ::= SEQUENCE { pmPolicyCodeScriptIndex Unsigned32, pmPolicyCodeSegment Unsigned32, pmPolicyCodeText PmUTF8String, pmPolicyCodeStatus RowStatus } pmPolicyCodeScriptIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique index for each policy condition or action. The code for each such condition or action may be composed of multiple entries in this table if the code cannot fit in one entry. Values of pmPolicyCodeScriptIndex may not be used unless they have previously been assigned in the pmPolicyConditionScriptIndex or pmPolicyActionScriptIndex objects." ::= { pmPolicyCodeEntry 1 } pmPolicyCodeSegment OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique index for each segment of a policy condition or action. When a policy condition or action spans multiple entries in this table, the code of that policy starts from the lowest-numbered segment and continues with increasing segment values until it ends with the highest-numbered segment." ::= { pmPolicyCodeEntry 2 } pmPolicyCodeText OBJECT-TYPE SYNTAX PmUTF8String (SIZE (1..1024)) MAX-ACCESS read-create STATUS current DESCRIPTION "A segment of policy code (condition or action). Lengthy Policy conditions or actions may be stored in multiple segments in this table that share the same value of pmPolicyCodeScriptIndex. When multiple segments are used, it is recommended that each segment be as large as is practical. Entries in this table are associated with policies by values of the pmPolicyConditionScriptIndex and pmPolicyActionScriptIndex objects. If the status of the related policy is active, then this object may not be modified." ::= { pmPolicyCodeEntry 3 } pmPolicyCodeStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this code entry. Entries in this table are associated with policies by values of the pmPolicyConditionScriptIndex and pmPolicyActionScriptIndex objects. If the status of the related policy is active, then this object can not be modified (i.e., deleted or set to notInService), nor may new entries be created. If the status of this object is active, no objects in this row may be modified." ::= { pmPolicyCodeEntry 4 } -- Element Type Registration Table pmElementTypeRegTable OBJECT-TYPE SYNTAX SEQUENCE OF PmElementTypeRegEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A registration table for element types managed by this system. The Element Type Registration table allows the manager to learn what element types are being managed by the system and to register new types, if necessary. An element type is registered by providing the OID of an SNMP object (i.e., without the instance). Each SNMP instance that exists under that object is a distinct element. The index of the element is the index part of the discovered OID. This index will be supplied to policy conditions and actions so that this code can inspect and configure the element. For example, this table might contain the following entries. The first three are agent-installed, and the 4th was downloaded by a management station: OIDPrefix MaxLatency Description StorageType ifEntry 100 mS interfaces - builtin readOnly 0.0 100 mS system element - builtin readOnly frCircuitEntry 100 mS FR Circuits - builtin readOnly hrSWRunEntry 60 sec Running Processes volatile Note that agents may automatically configure elements in this table for frequently used element types (interfaces, circuits, etc.). In particular, it may configure elements for whom discovery is optimized in one or both of the following ways: 1. The agent may discover elements by scanning internal data structures as opposed to issuing local SNMP requests. It is possible to recreate the exact semantics described in this table even if local SNMP requests are not issued. 2. The agent may receive asynchronous notification of new elements (for example, 'card inserted') and use that information to instantly create elements rather than through polling. A similar feature might be available for the deletion of elements. Note that the disposition of agent-installed entries is described by the pmPolicyStorageType object." ::= { pmMib 3 } pmElementTypeRegEntry OBJECT-TYPE SYNTAX PmElementTypeRegEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A registration of an element type. Note that some values of this table's index may result in an instance name that exceeds a length of 128 sub-identifiers, which exceeds the maximum for the SNMP protocol. Implementations should take care to avoid such values." INDEX { pmElementTypeRegOIDPrefix } ::= { pmElementTypeRegTable 1 } PmElementTypeRegEntry ::= SEQUENCE { pmElementTypeRegOIDPrefix OBJECT IDENTIFIER, pmElementTypeRegMaxLatency Unsigned32, pmElementTypeRegDescription PmUTF8String, pmElementTypeRegStorageType StorageType, pmElementTypeRegRowStatus RowStatus } pmElementTypeRegOIDPrefix OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS not-accessible STATUS current DESCRIPTION "This OBJECT IDENTIFIER value identifies a table in which all elements of this type will be found. Every row in the referenced table will be treated as an element for the period of time that it remains in the table. The agent will then execute policy conditions and actions as appropriate on each of these elements. This object identifier value is specified down to the 'entry' component (e.g., ifEntry) of the identifier. The index of each discovered row will be passed to each invocation of the policy condition and policy action. The actual mechanism by which instances are discovered is implementation dependent. Periodic walks of the table to discover the rows in the table is one such mechanism. This mechanism has the advantage that it can be performed by an agent with no knowledge of the names, syntax, or semantics of the MIB objects in the table. This mechanism also serves as the reference design. Other implementation-dependent mechanisms may be implemented that are more efficient (perhaps because they are hard coded) or that don't require polling. These mechanisms must discover the same elements as would the table-walking reference design. This object can contain a OBJECT IDENTIFIER, '0.0'. '0.0' represents the single instance of the system itself and provides an execution context for policies to operate on the 'system element' and on MIB objects modeled as scalars. For example, '0.0' gives an execution context for policy-based selection of the operating system code version (likely modeled as a scalar MIB object). The element type '0.0' always exists; as a consequence, no actual discovery will take place, and the pmElementTypeRegMaxLatency object will have no effect for the '0.0' element type. However, if the '0.0' element type is not registered in the table, policies will not be executed on the '0.0' element. When a policy is invoked on behalf of a '0.0' entry in this table, the element name will be '0.0', and there is no index of 'this element' (in other words, it has zero length). As this object is used in the index for the pmElementTypeRegTable, users of this table should be careful not to create entries that would result in instance names with more than 128 sub-identifiers." ::= { pmElementTypeRegEntry 2 } pmElementTypeRegMaxLatency OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The PM agent is responsible for discovering new elements of types that are registered. This object lets the manager control the maximum amount of time that may pass between the time an element is created and when it is discovered. In other words, in any given interval of this duration, all new elements must be discovered. Note that how the policy agent schedules the checking of various elements within this interval is an implementation-dependent matter." ::= { pmElementTypeRegEntry 3 } pmElementTypeRegDescription OBJECT-TYPE SYNTAX PmUTF8String (SIZE (0..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "A descriptive label for this registered type." ::= { pmElementTypeRegEntry 4 } pmElementTypeRegStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This object defines whether this row is kept in volatile storage and lost upon reboot or backed up by non-volatile or permanent storage. If the value of this object is 'permanent', no values in the associated row have to be writable." ::= { pmElementTypeRegEntry 5 } pmElementTypeRegRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this registration entry. If the value of this object is active, no objects in this row may be modified." ::= { pmElementTypeRegEntry 6 } -- Role Table pmRoleTable OBJECT-TYPE SYNTAX SEQUENCE OF PmRoleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The pmRoleTable is a read-create table that organizes role strings sorted by element. This table is used to create and modify role strings and their associations, as well as to allow a management station to learn about the existence of roles and their associations. It is the responsibility of the agent to keep track of any re-indexing of the underlying SNMP elements and to continue to associate role strings with the element with which they were initially configured. Policy MIB agents that have elements in multiple local SNMP contexts have to allow some roles to be assigned to elements in particular contexts. This is particularly true when some elements have the same names in different contexts and the context is required to disambiguate them. In those situations, a value for the pmRoleContextName may be provided. When a pmRoleContextName value is not provided, the assignment is to the element in the default context. Policy MIB agents that discover elements on other systems and execute policies on their behalf need to have access to role information for these remote elements. In such situations, role assignments for other systems can be stored in this table by providing values for the pmRoleContextEngineID parameters. For example: Example: element role context ctxEngineID #comment ifindex.1 gold local, default context ifindex.2 gold local, default context repeaterid.1 foo rptr1 local, rptr1 context repeaterid.1 bar rptr2 local, rptr2 context ifindex.1 gold '' A different system ifindex.1 gold '' B different system The agent must store role string associations in non-volatile storage." ::= { pmMib 4 } pmRoleEntry OBJECT-TYPE SYNTAX PmRoleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A role string entry associates a role string with an individual element. Note that some combinations of index values may result in an instance name that exceeds a length of 128 sub-identifiers, which exceeds the maximum for the SNMP protocol. Implementations should take care to avoid such combinations." INDEX { pmRoleElement, pmRoleContextName, pmRoleContextEngineID, pmRoleString } ::= { pmRoleTable 1 } PmRoleEntry ::= SEQUENCE { pmRoleElement RowPointer, pmRoleContextName SnmpAdminString, pmRoleContextEngineID OCTET STRING, pmRoleString PmUTF8String, pmRoleStatus RowStatus } pmRoleElement OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS not-accessible STATUS current DESCRIPTION "The element with which this role string is associated. For example, if the element is interface 3, then this object will contain the OID for 'ifIndex.3'. If the agent assigns new indexes in the MIB table to represent the same underlying element (re-indexing), the agent will modify this value to contain the new index for the underlying element. As this object is used in the index for the pmRoleTable, users of this table should be careful not to create entries that would result in instance names with more than 128 sub-identifiers." ::= { pmRoleEntry 1 } pmRoleContextName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the associated element is not in the default SNMP context for the target system, this object is used to identify the context. If the element is in the default context, this object is equal to the empty string." ::= { pmRoleEntry 2 } pmRoleContextEngineID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 5..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the associated element is on a remote system, this object is used to identify the remote system. This object contains the contextEngineID of the system for which this role string assignment is valid. If the element is on the local system this object will be the empty string." ::= { pmRoleEntry 3 } pmRoleString OBJECT-TYPE SYNTAX PmUTF8String (SIZE (0..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The role string that is associated with an element through this table. All role strings must have been successfully transformed by Stringprep RFC 3454. Management stations must perform this translation and must only set this object to string values that have been transformed. A role string is an administratively specified characteristic of a managed element (for example, an interface). It is a selector for policy rules, that determines the applicability of the rule to a particular managed element." ::= { pmRoleEntry 4 } pmRoleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this role string. If the value of this object is active, no object in this row may be modified." ::= { pmRoleEntry 5 } -- Capabilities table pmCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF PmCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The pmCapabilitiesTable contains a description of the inherent capabilities of the system so that management stations can learn of an agent's capabilities and differentially install policies based on the capabilities. Capabilities are expressed at the system level. There can be variation in how capabilities are realized from one vendor or model to the next. Management systems should consider these differences before selecting which policy to install in a system." ::= { pmMib 5 } pmCapabilitiesEntry OBJECT-TYPE SYNTAX PmCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A capabilities entry holds an OID indicating support for a particular capability. Capabilities may include hardware and software functions and the implementation of MIB Modules. The semantics of the OID are defined in the description of pmCapabilitiesType. Entries appear in this table if any element in the system has a specific capability. A capability should appear in this table only once, regardless of the number of elements in the system with that capability. An entry is removed from this table when the last element in the system that has the capability is removed. In some cases, capabilities are dynamic and exist only in software. This table should have an entry for the capability even if there are no current instances. Examples include systems with database or WEB services. While the system has the ability to create new databases or WEB services, the entry should exist. In these cases, the ability to create these services could come from other processes that are running in the system, even though there are no currently open databases or WEB servers running. Capabilities may include the implementation of MIB Modules but need not be limited to those that represent MIB Modules with one or more configurable objects. It may also be valuable to include entries for capabilities that do not include configuration objects, as that information, in combination with other entries in this table, might be used by the management software to determine whether to install a policy. Vendor software may also add entries in this table to express capabilities from their private branch. Note that some values of this table's index may result in an instance name that exceeds a length of 128 sub-identifiers, which exceeds the maximum for the SNMP protocol. Implementations should take care to avoid such values." INDEX { pmCapabilitiesType } ::= { pmCapabilitiesTable 1 } PmCapabilitiesEntry ::= SEQUENCE { pmCapabilitiesType OBJECT IDENTIFIER } pmCapabilitiesType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "There are three types of OIDs that may be present in the pmCapabilitiesType object: 1) The OID of a MODULE-COMPLIANCE macro that represents the highest level of compliance realized by the agent for that MIB Module. For example, an agent that implements the OSPF MIB Module at the highest level of compliance would have the value of '1.3.6.1.2.1.14.15.2' in the pmCapabilitiesType object. For software that realizes standard MIB Modules that do not have compliance statements, the base OID of the MIB Module should be used instead. If the OSPF MIB Module had not been created with a compliance statement, then the correct value of the pmCapabilitiesType would be '1.3.6.1.2.1.14'. In the cases where multiple compliance statements in a MIB Module are supported by the agent, and where one compliance statement does not by definition include the other, each of the compliance OIDs would have entries in this table. MIB Documents can contain more than one MIB Module. In the case of OSPF, there is a second MIB Module that describes notifications for the OSPF Version 2 Protocol. If the agent also realizes these functions, an entry will also exist for those capabilities in this table. 2) Vendors should install OIDs in this table that represent vendor-specific capabilities. These capabilities can be expressed just as those described above for MIB Modules on the standards track. In addition, vendors may install any OID they desire from their registered branch. The OIDs may be at any level of granularity, from the root of their entire branch to an instance of a single OID. There is no restriction on the number of registrations they may make, though care should be taken to avoid unnecessary entries. 3) OIDs that represent one capability or a collection of capabilities that could be any collection of MIB Objects or hardware or software functions may be created in working groups and registered in a MIB Module. Other entities (e.g., vendors) may also make registrations. Software will register these standard capability OIDs, as well as vendor specific OIDs. If the OID for a known capability is not present in the table, then it should be assumed that the capability is not implemented. As this object is used in the index for the pmCapabilitiesTable, users of this table should be careful not to create entries that would result in instance names with more than 128 sub-identifiers." ::= { pmCapabilitiesEntry 1 } -- Capabilities override table pmCapabilitiesOverrideTable OBJECT-TYPE SYNTAX SEQUENCE OF PmCapabilitiesOverrideEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The pmCapabilitiesOverrideTable allows management stations to override pmCapabilitiesTable entries that have been registered by the agent. This facility can be used to avoid situations in which managers in the network send policies to a system that has advertised a capability in the pmCapabilitiesTable but that should not be installed on this particular system. One example could be newly deployed equipment that is still in a trial state in a trial state or resources reserved for some other administrative reason. This table can also be used to override entries in the pmCapabilitiesTable through the use of the pmCapabilitiesOverrideState object. Capabilities can also be declared available in this table that were not registered in the pmCapabilitiesTable. A management application can make an entry in this table for any valid OID and declare the capability available by setting the pmCapabilitiesOverrideState for that row to valid(1)." ::= { pmMib 6 } pmCapabilitiesOverrideEntry OBJECT-TYPE SYNTAX PmCapabilitiesOverrideEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table indicates whether a particular capability is valid or invalid. Note that some values of this table's index may result in an instance name that exceeds a length of 128 sub-identifiers, which exceeds the maximum for the SNMP protocol. Implementations should take care to avoid such values." INDEX { pmCapabilitiesOverrideType } ::= { pmCapabilitiesOverrideTable 1 } PmCapabilitiesOverrideEntry ::= SEQUENCE { pmCapabilitiesOverrideType OBJECT IDENTIFIER, pmCapabilitiesOverrideState INTEGER, pmCapabilitiesOverrideRowStatus RowStatus } pmCapabilitiesOverrideType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is the OID of the capability that is declared valid or invalid by the pmCapabilitiesOverrideState value for this row. Any valid OID, as described in the pmCapabilitiesTable, is permitted in the pmCapabilitiesOverrideType object. This means that capabilities can be expressed at any level, from a specific instance of an object to a table or entire module. There are no restrictions on whether these objects are from standards track MIB documents or in the private branch of the MIB. If an entry exists in this table for which there is a corresponding entry in the pmCapabilitiesTable, then this entry shall have precedence over the entry in the pmCapabilitiesTable. All entries in this table must be preserved across reboots. As this object is used in the index for the pmCapabilitiesOverrideTable, users of this table should be careful not to create entries that would result in instance names with more than 128 sub-identifiers." ::= { pmCapabilitiesOverrideEntry 1 } pmCapabilitiesOverrideState OBJECT-TYPE SYNTAX INTEGER { invalid(1), valid(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "A pmCapabilitiesOverrideState of invalid indicates that management software should not send policies to this system for the capability identified in the pmCapabilitiesOverrideType for this row of the table. This behavior is the same whether the capability represented by the pmCapabilitiesOverrideType exists only in this table (that is, it was installed by an external management application) or exists in this table as well as the pmCapabilitiesTable. This would be the case when a manager wanted to disable a capability that the native management system found and registered in the pmCapabilitiesTable. An entry in this table that has a pmCapabilitiesOverrideState of valid should be treated as though it appeared in the pmCapabilitiesTable. If the entry also exists in the pmCapabilitiesTable in the pmCapabilitiesType object, and if the value of this object is valid, then the system shall operate as though this entry did not exist and policy installations and executions will continue in a normal fashion." ::= { pmCapabilitiesOverrideEntry 2 } pmCapabilitiesOverrideRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of this pmCapabilitiesOverrideEntry. If the value of this object is active, no object in this row may be modified." ::= { pmCapabilitiesOverrideEntry 3 } -- The Schedule Group pmSchedLocalTime OBJECT-TYPE SYNTAX DateAndTime (SIZE (11)) MAX-ACCESS read-only STATUS current DESCRIPTION "The local time used by the scheduler. Schedules that refer to calendar time will use the local time indicated by this object. An implementation MUST return all 11 bytes of the DateAndTime textual-convention so that a manager may retrieve the offset from GMT time." ::= { pmMib 7 } -- -- The schedule table that controls the scheduler. -- pmSchedTable OBJECT-TYPE SYNTAX SEQUENCE OF PmSchedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines schedules for policies." ::= { pmMib 8 } pmSchedEntry OBJECT-TYPE SYNTAX PmSchedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describing a particular schedule. Unless noted otherwise, writable objects of this row can be modified independently of the current value of pmSchedRowStatus, pmSchedAdminStatus and pmSchedOperStatus. In particular, it is legal to modify pmSchedWeekDay, pmSchedMonth, and pmSchedDay when pmSchedRowStatus is active." INDEX { pmSchedIndex } ::= { pmSchedTable 1 } PmSchedEntry ::= SEQUENCE { pmSchedIndex Unsigned32, pmSchedGroupIndex Unsigned32, pmSchedDescr PmUTF8String, pmSchedTimePeriod PmUTF8String, pmSchedMonth BITS, pmSchedDay BITS, pmSchedWeekDay BITS, pmSchedTimeOfDay PmUTF8String, pmSchedLocalOrUtc INTEGER, pmSchedStorageType StorageType, pmSchedRowStatus RowStatus } pmSchedIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The locally unique, administratively assigned index for this scheduling entry." ::= { pmSchedEntry 1 } pmSchedGroupIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The locally unique, administratively assigned index for the schedule group this scheduling entry belongs to. To assign multiple schedule entries to the same group, the pmSchedGroupIndex of each entry in the group will be set to the same value. This pmSchedGroupIndex value must be equal to the pmSchedIndex of one of the entries in the group. If the entry whose pmSchedIndex equals the pmSchedGroupIndex for the group is deleted, the agent will assign a new pmSchedGroupIndex to all remaining members of the group. If an entry is not a member of a group, its pmSchedGroupIndex must be assigned to the value of its pmSchedIndex. Policies that are controlled by a group of schedule entries are active when any schedule in the group is active." ::= { pmSchedEntry 2 } pmSchedDescr OBJECT-TYPE SYNTAX PmUTF8String MAX-ACCESS read-create STATUS current DESCRIPTION "The human-readable description of the purpose of this scheduling entry." DEFVAL { ''H } ::= { pmSchedEntry 3 } pmSchedTimePeriod OBJECT-TYPE SYNTAX PmUTF8String (SIZE (0..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The overall range of calendar dates and times over which this schedule is active. It is stored in a slightly extended version of the format for a 'period-explicit' defined in RFC 2445. This format is expressed as a string representing the starting date and time, in which the character 'T' indicates the beginning of the time portion, followed by the solidus character, '/', followed by a similar string representing an end date and time. The start of the period MUST be before the end of the period. Date-Time values are expressed as substrings of the form 'yyyymmddThhmmss'. For example: 20000101T080000/20000131T130000 January 1, 2000, 0800 through January 31, 2000, 1PM The 'Date with UTC time' format defined in RFC 2445 in which the Date-Time string ends with the character 'Z' is not allowed. This 'period-explicit' format is also extended to allow two special cases in which one of the Date-Time strings is replaced with a special string defined in RFC 2445: 1. If the first Date-Time value is replaced with the string 'THISANDPRIOR', then the value indicates that the schedule is active at any time prior to the Date-Time that appears after the '/'. 2. If the second Date-Time is replaced with the string 'THISANDFUTURE', then the value indicates that the schedule is active at any time after the Date-Time that appears before the '/'. Note that although RFC 2445 defines these two strings, they are not specified for use in the 'period-explicit' format. The use of these strings represents an extension to the 'period-explicit' format." ::= { pmSchedEntry 4 } pmSchedMonth OBJECT-TYPE SYNTAX BITS { january(0), february(1), march(2), april(3), may(4), june(5), july(6), august(7), september(8), october(9), november(10), december(11) } MAX-ACCESS read-create STATUS current DESCRIPTION "Within the overall time period specified in the pmSchedTimePeriod object, the value of this object specifies the specific months within that time period when the schedule is active. Setting all bits will cause the schedule to act independently of the month." DEFVAL { { january, february, march, april, may, june, july, august, september, october, november, december } } ::= { pmSchedEntry 5 } pmSchedDay OBJECT-TYPE SYNTAX BITS { d1(0), d2(1), d3(2), d4(3), d5(4), d6(5), d7(6), d8(7), d9(8), d10(9), d11(10), d12(11), d13(12), d14(13), d15(14), d16(15), d17(16), d18(17), d19(18), d20(19), d21(20), d22(21), d23(22), d24(23), d25(24), d26(25), d27(26), d28(27), d29(28), d30(29), d31(30), r1(31), r2(32), r3(33), r4(34), r5(35), r6(36), r7(37), r8(38), r9(39), r10(40), r11(41), r12(42), r13(43), r14(44), r15(45), r16(46), r17(47), r18(48), r19(49), r20(50), r21(51), r22(52), r23(53), r24(54), r25(55), r26(56), r27(57), r28(58), r29(59), r30(60), r31(61) } MAX-ACCESS read-create STATUS current DESCRIPTION "Within the overall time period specified in the pmSchedTimePeriod object, the value of this object specifies the specific days of the month within that time period when the schedule is active. There are two sets of bits one can use to define the day within a month: Enumerations starting with the letter 'd' indicate a day in a month relative to the first day of a month. The first day of the month can therefore be specified by setting the bit d1(0), and d31(30) means the last day of a month with 31 days. Enumerations starting with the letter 'r' indicate a day in a month in reverse order, relative to the last day of a month. The last day in the month can therefore be specified by setting the bit r1(31), and r31(61) means the first day of a month with 31 days. Setting multiple bits will include several days in the set of possible days for this schedule. Setting all bits starting with the letter 'd' or all bits starting with the letter 'r' will cause the schedule to act independently of the day of the month." DEFVAL { { d1, d2, d3, d4, d5, d6, d7, d8, d9, d10, d11, d12, d13, d14, d15, d16, d17, d18, d19, d20, d21, d22, d23, d24, d25, d26, d27, d28, d29, d30, d31, r1, r2, r3, r4, r5, r6, r7, r8, r9, r10, r11, r12, r13, r14, r15, r16, r17, r18, r19, r20, r21, r22, r23, r24, r25, r26, r27, r28, r29, r30, r31 } } ::= { pmSchedEntry 6 } pmSchedWeekDay OBJECT-TYPE SYNTAX BITS { sunday(0), monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "Within the overall time period specified in the pmSchedTimePeriod object, the value of this object specifies the specific days of the week within that time period when the schedule is active. Setting all bits will cause the schedule to act independently of the day of the week." DEFVAL { { sunday, monday, tuesday, wednesday, thursday, friday, saturday } } ::= { pmSchedEntry 7 } pmSchedTimeOfDay OBJECT-TYPE SYNTAX PmUTF8String (SIZE (0..15)) MAX-ACCESS read-create STATUS current DESCRIPTION "Within the overall time period specified in the pmSchedTimePeriod object, the value of this object specifies the range of times in a day when the schedule is active. This value is stored in a format based on the RFC 2445 format for 'time': The character 'T' followed by a 'time' string, followed by the solidus character, '/', followed by the character 'T', followed by a second time string. The first time indicates the beginning of the range, and the second time indicates the end. Thus, this value takes the following form: 'Thhmmss/Thhmmss'. The second substring always identifies a later time than the first substring. To allow for ranges that span midnight, however, the value of the second string may be smaller than the value of the first substring. Thus, 'T080000/T210000' identifies the range from 0800 until 2100, whereas 'T210000/T080000' identifies the range from 2100 until 0800 of the following day. When a range spans midnight, by definition it includes parts of two successive days. When one of these days is also selected by either the MonthOfYearMask, DayOfMonthMask, and/or DayOfWeekMask, but the other day is not, then the policy is active only during the portion of the range that falls on the selected day. For example, if the range extends from 2100 until 0800, and the day of week mask selects Monday and Tuesday, then the policy is active during the following three intervals: From midnight Sunday until 0800 Monday From 2100 Monday until 0800 Tuesday From 2100 Tuesday until 23:59:59 Tuesday Setting this value to 'T000000/T235959' will cause the schedule to act independently of the time of day." DEFVAL { '543030303030302F54323335393539'H } -- T000000/T235959 ::= { pmSchedEntry 8 } pmSchedLocalOrUtc OBJECT-TYPE SYNTAX INTEGER { localTime(1), utcTime(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates whether the times represented in the TimePeriod object and in the various Mask objects represent local times or UTC times." DEFVAL { utcTime } ::= { pmSchedEntry 9 } pmSchedStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This object defines whether this schedule entry is kept in volatile storage and lost upon reboot or backed up by non-volatile or permanent storage. Conceptual rows having the value 'permanent' must allow write access to the columnar objects pmSchedDescr, pmSchedWeekDay, pmSchedMonth, and pmSchedDay. If the value of this object is 'permanent', no values in the associated row have to be writable." DEFVAL { volatile } ::= { pmSchedEntry 10 } pmSchedRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this schedule entry. If the value of this object is active, no object in this row may be modified." ::= { pmSchedEntry 11 } -- Policy Tracking -- The "policy to element" (PE) table and the "element to policy" (EP) -- table track the status of execution contexts grouped by policy and -- element respectively. pmTrackingPETable OBJECT-TYPE SYNTAX SEQUENCE OF PmTrackingPEEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The pmTrackingPETable describes what elements are active (under control of) a policy. This table is indexed in order to optimize retrieval of the entire status for a given policy." ::= { pmMib 9 } pmTrackingPEEntry OBJECT-TYPE SYNTAX PmTrackingPEEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the pmTrackingPETable. The pmPolicyIndex in the index specifies the policy tracked by this entry. Note that some combinations of index values may result in an instance name that exceeds a length of 128 sub-identifiers, which exceeds the maximum for the SNMP protocol. Implementations should take care to avoid such combinations." INDEX { pmPolicyIndex, pmTrackingPEElement, pmTrackingPEContextName, pmTrackingPEContextEngineID } ::= { pmTrackingPETable 1 } PmTrackingPEEntry ::= SEQUENCE { pmTrackingPEElement RowPointer, pmTrackingPEContextName SnmpAdminString, pmTrackingPEContextEngineID OCTET STRING, pmTrackingPEInfo BITS } pmTrackingPEElement OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS not-accessible STATUS current DESCRIPTION "The element that is acted upon by the associated policy. As this object is used in the index for the pmTrackingPETable, users of this table should be careful not to create entries that would result in instance names with more than 128 sub-identifiers." ::= { pmTrackingPEEntry 1 } pmTrackingPEContextName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the associated element is not in the default SNMP context for the target system, this object is used to identify the context. If the element is in the default context, this object is equal to the empty string." ::= { pmTrackingPEEntry 2 } pmTrackingPEContextEngineID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 5..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the associated element is on a remote system, this object is used to identify the remote system. This object contains the contextEngineID of the system on which the associated element resides. If the element is on the local system, this object will be the empty string." ::= { pmTrackingPEEntry 3 } pmTrackingPEInfo OBJECT-TYPE SYNTAX BITS { actionSkippedDueToPrecedence(0), conditionRunTimeException(1), conditionUserSignal(2), actionRunTimeException(3), actionUserSignal(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns information about the previous policy script executions. If the actionSkippedDueToPrecedence(1) bit is set, the last execution of the associated policy condition returned non-zero, but the action is not active, because it was trumped by a matching policy condition in the same precedence group with a higher precedence value. If the conditionRunTimeException(2) bit is set, the last execution of the associated policy condition encountered a run-time exception and aborted. If the conditionUserSignal(3) bit is set, the last execution of the associated policy condition called the signalError() function. If the actionRunTimeException(4) bit is set, the last execution of the associated policy action encountered a run-time exception and aborted. If the actionUserSignal(5) bit is set, the last execution of the associated policy action called the signalError() function. Entries will only exist in this table of one or more bits are set. In particular, if an entry does not exist for a particular policy/element combination, it can be assumed that the policy's condition did not match 'this element'." ::= { pmTrackingPEEntry 4 } -- Element to Policy Table pmTrackingEPTable OBJECT-TYPE SYNTAX SEQUENCE OF PmTrackingEPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The pmTrackingEPTable describes what policies are controlling an element. This table is indexed in order to optimize retrieval of the status of all policies active for a given element." ::= { pmMib 10 } pmTrackingEPEntry OBJECT-TYPE SYNTAX PmTrackingEPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the pmTrackingEPTable. Entries exist for all element/policy combinations for which the policy's condition matches and only if the schedule for the policy is active. The pmPolicyIndex in the index specifies the policy tracked by this entry. Note that some combinations of index values may result in an instance name that exceeds a length of 128 sub-identifiers, which exceeds the maximum for the SNMP protocol. Implementations should take care to avoid such combinations." INDEX { pmTrackingEPElement, pmTrackingEPContextName, pmTrackingEPContextEngineID, pmPolicyIndex } ::= { pmTrackingEPTable 1 } PmTrackingEPEntry ::= SEQUENCE { pmTrackingEPElement RowPointer, pmTrackingEPContextName SnmpAdminString, pmTrackingEPContextEngineID OCTET STRING, pmTrackingEPStatus INTEGER } pmTrackingEPElement OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS not-accessible STATUS current DESCRIPTION "The element acted upon by the associated policy. As this object is used in the index for the pmTrackingEPTable, users of this table should be careful not to create entries that would result in instance names with more than 128 sub-identifiers." ::= { pmTrackingEPEntry 1 } pmTrackingEPContextName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the associated element is not in the default SNMP context for the target system, this object is used to identify the context. If the element is in the default context, this object is equal to the empty string." ::= { pmTrackingEPEntry 2 } pmTrackingEPContextEngineID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 5..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the associated element is on a remote system, this object is used to identify the remote system. This object contains the contextEngineID of the system on which the associated element resides. If the element is on the local system, this object will be the empty string." ::= { pmTrackingEPEntry 3 } pmTrackingEPStatus OBJECT-TYPE SYNTAX INTEGER { on(1), forceOff(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This entry will only exist if the calendar for the policy is active and if the associated policyCondition returned 1 for 'this element'. A policy can be forcibly disabled on a particular element by setting this value to forceOff(2). The agent should then act as though the policyCondition failed for 'this element'. The forceOff(2) state will persist (even across reboots) until this value is set to on(1) by a management request. The forceOff(2) state may be set even if the entry does not previously exist so that future policy invocations can be avoided. Unless forcibly disabled, if this entry exists, its value will be on(1)." ::= { pmTrackingEPEntry 4 } -- Policy Debugging Table pmDebuggingTable OBJECT-TYPE SYNTAX SEQUENCE OF PmDebuggingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Policies that have debugging turned on will generate a log entry in the policy debugging table for every runtime exception that occurs in either the condition or action code. The pmDebuggingTable logs debugging messages when policies experience run-time exceptions in either the condition or action code and the associated pmPolicyDebugging object has been turned on. The maximum number of debugging entries that will be stored and the maximum length of time an entry will be kept are an implementation-dependent manner. If entries must be discarded to make room for new entries, the oldest entries must be discarded first. If the system restarts, all debugging entries may be deleted." ::= { pmMib 11 } pmDebuggingEntry OBJECT-TYPE SYNTAX PmDebuggingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the pmDebuggingTable. The pmPolicyIndex in the index specifies the policy that encountered the exception that led to this log entry. Note that some combinations of index values may result in an instance name that exceeds a length of 128 sub-identifiers, which exceeds the maximum for the SNMP protocol. Implementations should take care to avoid such combinations." INDEX { pmPolicyIndex, pmDebuggingElement, pmDebuggingContextName, pmDebuggingContextEngineID, pmDebuggingLogIndex } ::= { pmDebuggingTable 1 } PmDebuggingEntry ::= SEQUENCE { pmDebuggingElement RowPointer, pmDebuggingContextName SnmpAdminString, pmDebuggingContextEngineID OCTET STRING, pmDebuggingLogIndex Unsigned32, pmDebuggingMessage PmUTF8String } pmDebuggingElement OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS not-accessible STATUS current DESCRIPTION "The element the policy was executing on when it encountered the error that led to this log entry. For example, if the element is interface 3, then this object will contain the OID for 'ifIndex.3'. As this object is used in the index for the pmDebuggingTable, users of this table should be careful not to create entries that would result in instance names with more than 128 sub-identifiers." ::= { pmDebuggingEntry 1 } pmDebuggingContextName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the associated element is not in the default SNMP context for the target system, this object is used to identify the context. If the element is in the default context, this object is equal to the empty string." ::= { pmDebuggingEntry 2 } pmDebuggingContextEngineID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 5..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the associated element is on a remote system, this object is used to identify the remote system. This object contains the contextEngineID of the system on which the associated element resides. If the element is on the local system, this object will be the empty string." ::= { pmDebuggingEntry 3 } pmDebuggingLogIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique index for this log entry among other log entries for this policy/element combination." ::= { pmDebuggingEntry 4 } pmDebuggingMessage OBJECT-TYPE SYNTAX PmUTF8String (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "An error message generated by the policy execution environment. It is recommended that this message include the time of day when the message was generated, if known." ::= { pmDebuggingEntry 5 } -- Notifications pmNotifications OBJECT IDENTIFIER ::= { pmMib 0 } pmNewRoleNotification NOTIFICATION-TYPE OBJECTS { pmRoleStatus } STATUS current DESCRIPTION "The pmNewRoleNotification is sent when an agent is configured with its first instance of a previously unused role string (not every time a new element is given a particular role). An instance of the pmRoleStatus object is sent containing the new roleString in its index. In the event that two or more elements are given the same role simultaneously, it is an implementation-dependent matter as to which pmRoleTable instance will be included in the notification." ::= { pmNotifications 1 } pmNewCapabilityNotification NOTIFICATION-TYPE OBJECTS { pmCapabilitiesType } STATUS current DESCRIPTION "The pmNewCapabilityNotification is sent when an agent gains a new capability that did not previously exist in any element on the system (not every time an element gains a particular capability). An instance of the pmCapabilitiesType object is sent containing the identity of the new capability. In the event that two or more elements gain the same capability simultaneously, it is an implementation-dependent matter as to which pmCapabilitiesType instance will be included in the notification." ::= { pmNotifications 2 } pmAbnormalTermNotification NOTIFICATION-TYPE OBJECTS { pmTrackingPEInfo } STATUS current DESCRIPTION "The pmAbnormalTermNotification is sent when a policy's pmPolicyAbnormalTerminations gauge value changes from zero to any value greater than zero and no such notification has been sent for that policy in the last 5 minutes. The notification contains an instance of the pmTrackingPEInfo object where the pmPolicyIndex component of the index identifies the associated policy and the rest of the index identifies an element on which the policy failed." ::= { pmNotifications 3 } -- Compliance Statements pmConformance OBJECT IDENTIFIER ::= { pmMib 12 } pmCompliances OBJECT IDENTIFIER ::= { pmConformance 1 } pmGroups OBJECT IDENTIFIER ::= { pmConformance 2 } pmCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Describes the requirements for conformance to the Policy-Based Management MIB" MODULE -- this module MANDATORY-GROUPS { pmPolicyManagementGroup, pmSchedGroup, pmNotificationGroup } ::= { pmCompliances 1 } pmPolicyManagementGroup OBJECT-GROUP OBJECTS { pmPolicyPrecedenceGroup, pmPolicyPrecedence, pmPolicySchedule, pmPolicyElementTypeFilter, pmPolicyConditionScriptIndex, pmPolicyActionScriptIndex, pmPolicyParameters, pmPolicyConditionMaxLatency, pmPolicyActionMaxLatency, pmPolicyMaxIterations, pmPolicyDescription, pmPolicyMatches, pmPolicyAbnormalTerminations, pmPolicyExecutionErrors, pmPolicyDebugging, pmPolicyStorageType, pmPolicyAdminStatus, pmPolicyRowStatus, pmPolicyCodeText, pmPolicyCodeStatus, pmElementTypeRegMaxLatency, pmElementTypeRegDescription, pmElementTypeRegStorageType, pmElementTypeRegRowStatus, pmRoleStatus, pmCapabilitiesType, pmCapabilitiesOverrideState, pmCapabilitiesOverrideRowStatus, pmTrackingPEInfo, pmTrackingEPStatus, pmDebuggingMessage } STATUS current DESCRIPTION "Objects that allow for the creation and management of configuration policies." ::= { pmGroups 1 } pmSchedGroup OBJECT-GROUP OBJECTS { pmSchedLocalTime, pmSchedGroupIndex, pmSchedDescr, pmSchedTimePeriod, pmSchedMonth, pmSchedDay, pmSchedWeekDay, pmSchedTimeOfDay, pmSchedLocalOrUtc, pmSchedStorageType, pmSchedRowStatus } STATUS current DESCRIPTION "Objects that allow for the scheduling of policies." ::= { pmGroups 2 } pmNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { pmNewRoleNotification, pmNewCapabilityNotification, pmAbnormalTermNotification } STATUS current DESCRIPTION "Notifications sent by an Policy MIB agent." ::= { pmGroups 3 } pmBaseFunctionLibrary OBJECT IDENTIFIER ::= { pmGroups 4 } END