RADIUS-DYNAUTH-CLIENT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, Integer32, mib-2, TimeTicks FROM SNMPv2-SMI -- [RFC2578] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411] InetAddressType, InetAddress, InetPortNumber FROM INET-ADDRESS-MIB -- [RFC4001] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; -- [RFC2580] radiusDynAuthClientMIB MODULE-IDENTITY LAST-UPDATED "200608290000Z" -- 29 August 2006 ORGANIZATION "IETF RADEXT Working Group" CONTACT-INFO " Stefaan De Cnodder Alcatel Francis Wellesplein 1 B-2018 Antwerp Belgium Phone: +32 3 240 85 15 EMail: [email protected] Nagi Reddy Jonnala Cisco Systems, Inc. Divyasree Chambers, B Wing, O'Shaugnessy Road, Bangalore-560027, India. Phone: +91 94487 60828 EMail: [email protected] Murtaza Chiba Cisco Systems, Inc. 170 West Tasman Dr. San Jose CA, 95134 Phone: +1 408 525 7198 EMail: [email protected] " DESCRIPTION "The MIB module for entities implementing the client side of the Dynamic Authorization Extensions to the Remote Authentication Dial-In User Service (RADIUS) protocol. Copyright (C) The Internet Society (2006). Initial version as published in RFC 4672; for full legal notices see the RFC itself." REVISION "200609290000Z" -- 29 August 2006 DESCRIPTION "Initial version as published in RFC 4672" ::= { mib-2 145 } radiusDynAuthClientMIBObjects OBJECT IDENTIFIER ::= { radiusDynAuthClientMIB 1 } radiusDynAuthClientScalars OBJECT IDENTIFIER ::= { radiusDynAuthClientMIBObjects 1 } radiusDynAuthClientDisconInvalidServerAddresses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Disconnect-Ack and Disconnect-NAK packets received from unknown addresses. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." ::= { radiusDynAuthClientScalars 1 } radiusDynAuthClientCoAInvalidServerAddresses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CoA-Ack and CoA-NAK packets received from unknown addresses. Disconnect-NAK packets received from unknown addresses. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." ::= { radiusDynAuthClientScalars 2 } radiusDynAuthServerTable OBJECT-TYPE SYNTAX SEQUENCE OF RadiusDynAuthServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the RADIUS Dynamic Authorization Servers with which the client shares a secret." ::= { radiusDynAuthClientMIBObjects 2 } radiusDynAuthServerEntry OBJECT-TYPE SYNTAX RadiusDynAuthServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing one Dynamic Authorization Server with which the client shares a secret." INDEX { radiusDynAuthServerIndex } ::= { radiusDynAuthServerTable 1 } RadiusDynAuthServerEntry ::= SEQUENCE { radiusDynAuthServerIndex Integer32, radiusDynAuthServerAddressType InetAddressType, radiusDynAuthServerAddress InetAddress, radiusDynAuthServerClientPortNumber InetPortNumber, radiusDynAuthServerID SnmpAdminString, radiusDynAuthClientRoundTripTime TimeTicks, radiusDynAuthClientDisconRequests Counter32, radiusDynAuthClientDisconAuthOnlyRequests Counter32, radiusDynAuthClientDisconRetransmissions Counter32, radiusDynAuthClientDisconAcks Counter32, radiusDynAuthClientDisconNaks Counter32, radiusDynAuthClientDisconNakAuthOnlyRequest Counter32, radiusDynAuthClientDisconNakSessNoContext Counter32, radiusDynAuthClientMalformedDisconResponses Counter32, radiusDynAuthClientDisconBadAuthenticators Counter32, radiusDynAuthClientDisconPendingRequests Gauge32, radiusDynAuthClientDisconTimeouts Counter32, radiusDynAuthClientDisconPacketsDropped Counter32, radiusDynAuthClientCoARequests Counter32, radiusDynAuthClientCoAAuthOnlyRequest Counter32, radiusDynAuthClientCoARetransmissions Counter32, radiusDynAuthClientCoAAcks Counter32, radiusDynAuthClientCoANaks Counter32, radiusDynAuthClientCoANakAuthOnlyRequest Counter32, radiusDynAuthClientCoANakSessNoContext Counter32, radiusDynAuthClientMalformedCoAResponses Counter32, radiusDynAuthClientCoABadAuthenticators Counter32, radiusDynAuthClientCoAPendingRequests Gauge32, radiusDynAuthClientCoATimeouts Counter32, radiusDynAuthClientCoAPacketsDropped Counter32, radiusDynAuthClientUnknownTypes Counter32, radiusDynAuthClientCounterDiscontinuity TimeTicks } radiusDynAuthServerIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number uniquely identifying each RADIUS Dynamic Authorization Server with which this Dynamic Authorization Client communicates. This number is allocated by the agent implementing this MIB module and is unique in this context." ::= { radiusDynAuthServerEntry 1 } radiusDynAuthServerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of IP address of the RADIUS Dynamic Authorization Server referred to in this table entry." ::= { radiusDynAuthServerEntry 2 } radiusDynAuthServerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address value of the RADIUS Dynamic Authorization Server referred to in this table entry using the version neutral IP address format. The type of this address is determined by the value of the radiusDynAuthServerAddressType object." ::= { radiusDynAuthServerEntry 3 } radiusDynAuthServerClientPortNumber OBJECT-TYPE SYNTAX InetPortNumber (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The UDP destination port that the RADIUS Dynamic Authorization Client is using to send requests to this server. The value zero is invalid." ::= { radiusDynAuthServerEntry 4 } radiusDynAuthServerID OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The NAS-Identifier of the RADIUS Dynamic Authorization Server referred to in this table entry. This is not necessarily the same as sysName in MIB II." REFERENCE "RFC 2865, Section 5.32, NAS-Identifier." ::= { radiusDynAuthServerEntry 5 } radiusDynAuthClientRoundTripTime OBJECT-TYPE SYNTAX TimeTicks UNITS "hundredths of a second" MAX-ACCESS read-only STATUS current DESCRIPTION "The time interval (in hundredths of a second) between the most recent Disconnect or CoA request and the receipt of the corresponding Disconnect or CoA reply. A value of zero is returned if no reply has been received yet from this server." ::= { radiusDynAuthServerEntry 6 } radiusDynAuthClientDisconRequests OBJECT-TYPE SYNTAX Counter32 UNITS "requests" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS Disconnect-Requests sent to this Dynamic Authorization Server. This also includes the RADIUS Disconnect-Requests that have a Service-Type attribute with value 'Authorize Only'. Disconnect-NAK packets received from unknown addresses. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM)." ::= { radiusDynAuthServerEntry 7 } radiusDynAuthClientDisconAuthOnlyRequests OBJECT-TYPE SYNTAX Counter32 UNITS "requests" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS Disconnect-Requests that include a Service-Type attribute with value 'Authorize Only' sent to this Dynamic Authorization Server. Disconnect-NAK packets received from unknown addresses. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM)." ::= { radiusDynAuthServerEntry 8 } radiusDynAuthClientDisconRetransmissions OBJECT-TYPE SYNTAX Counter32 UNITS "retransmissions" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS Disconnect-request packets retransmitted to this RADIUS Dynamic Authorization Server. Disconnect-NAK packets received from unknown addresses. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM)." ::= { radiusDynAuthServerEntry 9 } radiusDynAuthClientDisconAcks OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS Disconnect-ACK packets received from this Dynamic Authorization Server. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM)." ::= { radiusDynAuthServerEntry 10 } radiusDynAuthClientDisconNaks OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS Disconnect-NAK packets received from this Dynamic Authorization Server. This includes the RADIUS Disconnect-NAK packets received with a Service-Type attribute with value 'Authorize Only' and the RADIUS Disconnect-NAK packets received if no session context was found. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM)." ::= { radiusDynAuthServerEntry 11 } radiusDynAuthClientDisconNakAuthOnlyRequest OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS Disconnect-NAK packets that include a Service-Type attribute with value 'Authorize Only' received from this Dynamic Authorization Server. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM)." ::= { radiusDynAuthServerEntry 12 } radiusDynAuthClientDisconNakSessNoContext OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS Disconnect-NAK packets received from this Dynamic Authorization Server because no session context was found; i.e., it includes an Error-Cause attribute with value 503 ('Session Context Not Found'). This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM)." ::= { radiusDynAuthServerEntry 13 } radiusDynAuthClientMalformedDisconResponses OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of malformed RADIUS Disconnect-Ack and Disconnect-NAK packets received from this Dynamic Authorization Server. Bad authenticators and unknown types are not included as malformed Disconnect-Ack and Disconnect-NAK packets. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM), and Section 2.3, Packet Format." ::= { radiusDynAuthServerEntry 14 } radiusDynAuthClientDisconBadAuthenticators OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS Disconnect-Ack and Disconnect-NAK packets that contained invalid Authenticator field received from this Dynamic Authorization Server. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM), and Section 2.3, Packet Format." ::= { radiusDynAuthServerEntry 15 } radiusDynAuthClientDisconPendingRequests OBJECT-TYPE SYNTAX Gauge32 UNITS "requests" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS Disconnect-request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an Disconnect-Request is sent and decremented due to receipt of a Disconnect-Ack, a Disconnect-NAK, a timeout, or a retransmission." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM)." ::= { radiusDynAuthServerEntry 16 } radiusDynAuthClientDisconTimeouts OBJECT-TYPE SYNTAX Counter32 UNITS "timeouts" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Disconnect request timeouts to this server. After a timeout, the client may retry to the same server or give up. A retry to the same server is counted as a retransmit and as a timeout. A send to a different server is counted as a Disconnect-Request and as a timeout. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM)." ::= { radiusDynAuthServerEntry 17 } radiusDynAuthClientDisconPacketsDropped OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of incoming Disconnect-Ack and Disconnect-NAK packets from this Dynamic Authorization Server silently discarded by the client application for some reason other than malformed, bad authenticators, or unknown types. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.1, Disconnect Messages (DM), and Section 2.3, Packet Format." ::= { radiusDynAuthServerEntry 18 } radiusDynAuthClientCoARequests OBJECT-TYPE SYNTAX Counter32 UNITS "requests" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS CoA-Requests sent to this Dynamic Authorization Server. This also includes CoA requests that have a Service-Type attribute with value 'Authorize Only'. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA)." ::= { radiusDynAuthServerEntry 19 } radiusDynAuthClientCoAAuthOnlyRequest OBJECT-TYPE SYNTAX Counter32 UNITS "requests" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS CoA-requests that include a Service-Type attribute with value 'Authorize Only' sent to this Dynamic Authorization Client. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA)." ::= { radiusDynAuthServerEntry 20 } radiusDynAuthClientCoARetransmissions OBJECT-TYPE SYNTAX Counter32 UNITS "retransmissions" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS CoA-request packets retransmitted to this RADIUS Dynamic Authorization Server. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA)." ::= { radiusDynAuthServerEntry 21 } radiusDynAuthClientCoAAcks OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS CoA-ACK packets received from this Dynamic Authorization Server. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA)." ::= { radiusDynAuthServerEntry 22 } radiusDynAuthClientCoANaks OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS CoA-NAK packets received from this Dynamic Authorization Server. This includes the RADIUS CoA-NAK packets received with a Service-Type attribute with value 'Authorize Only' and the RADIUS CoA-NAK packets received because no session context was found. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA)." ::= { radiusDynAuthServerEntry 23 } radiusDynAuthClientCoANakAuthOnlyRequest OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS CoA-NAK packets that include a Service-Type attribute with value 'Authorize Only' received from this Dynamic Authorization Server. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA)." ::= { radiusDynAuthServerEntry 24 } radiusDynAuthClientCoANakSessNoContext OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS CoA-NAK packets received from this Dynamic Authorization Server because no session context was found; i.e., it includes an Error-Cause attribute with value 503 ('Session Context Not Found'). This counter may experience a discontinuity when the DAC module (re)starts as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA)." ::= { radiusDynAuthServerEntry 25 } radiusDynAuthClientMalformedCoAResponses OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of malformed RADIUS CoA-Ack and CoA-NAK packets received from this Dynamic Authorization Server. Bad authenticators and unknown types are not included as malformed CoA-Ack and CoA-NAK packets. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA), and Section 2.3, Packet Format." ::= { radiusDynAuthServerEntry 26 } radiusDynAuthClientCoABadAuthenticators OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS CoA-Ack and CoA-NAK packets that contained invalid Authenticator field received from this Dynamic Authorization Server. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA), and Section 2.3, Packet Format." ::= { radiusDynAuthServerEntry 27 } radiusDynAuthClientCoAPendingRequests OBJECT-TYPE SYNTAX Gauge32 UNITS "requests" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RADIUS CoA-request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an CoA-Request is sent and decremented due to receipt of a CoA-Ack, a CoA-NAK, or a timeout, or a retransmission." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA)." ::= { radiusDynAuthServerEntry 28 } radiusDynAuthClientCoATimeouts OBJECT-TYPE SYNTAX Counter32 UNITS "timeouts" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of CoA request timeouts to this server. After a timeout, the client may retry to the same server or give up. A retry to the same server is counted as a retransmit and as a timeout. A send to a different server is counted as a CoA-Request and as a timeout. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA)." ::= { radiusDynAuthServerEntry 29 } radiusDynAuthClientCoAPacketsDropped OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of incoming CoA-Ack and CoA-NAK from this Dynamic Authorization Server silently discarded by the client application for some reason other than malformed, bad authenticators, or unknown types. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.2, Change-of-Authorization Messages (CoA), and Section 2.3, Packet Format." ::= { radiusDynAuthServerEntry 30 } radiusDynAuthClientUnknownTypes OBJECT-TYPE SYNTAX Counter32 UNITS "replies" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of incoming packets of unknown types that were received on the Dynamic Authorization port. This counter may experience a discontinuity when the DAC module (re)starts, as indicated by the value of radiusDynAuthClientCounterDiscontinuity." REFERENCE "RFC 3576, Section 2.3, Packet Format." ::= { radiusDynAuthServerEntry 31 } radiusDynAuthClientCounterDiscontinuity OBJECT-TYPE SYNTAX TimeTicks UNITS "hundredths of a second" MAX-ACCESS read-only STATUS current DESCRIPTION "The time (in hundredths of a second) since the last counter discontinuity. A discontinuity may be the result of a reinitialization of the DAC module within the managed entity." ::= { radiusDynAuthServerEntry 32 } -- conformance information radiusDynAuthClientMIBConformance OBJECT IDENTIFIER ::= { radiusDynAuthClientMIB 2 } radiusDynAuthClientMIBCompliances OBJECT IDENTIFIER ::= { radiusDynAuthClientMIBConformance 1 } radiusDynAuthClientMIBGroups OBJECT IDENTIFIER ::= { radiusDynAuthClientMIBConformance 2 } -- compliance statements radiusDynAuthClientMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities implementing the RADIUS Dynamic Authorization Client. Implementation of this module is for entities that support IPv4 and/or IPv6." MODULE -- this module MANDATORY-GROUPS { radiusDynAuthClientMIBGroup } OBJECT radiusDynAuthServerAddressType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is only required to support IPv4 and globally unique IPv6 addresses." OBJECT radiusDynAuthServerAddress SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is only required to support IPv4 and globally unique IPv6 addresses." GROUP radiusDynAuthClientAuthOnlyGroup DESCRIPTION "Only required for Dynamic Authorization Clients that are supporting Service-Type attributes with value 'Authorize-Only'." GROUP radiusDynAuthClientNoSessGroup DESCRIPTION "This group is not required if the Dynamic Authorization Server cannot easily determine whether a session exists (e.g., in case of a RADIUS proxy)." ::= { radiusDynAuthClientMIBCompliances 1 } -- units of conformance radiusDynAuthClientMIBGroup OBJECT-GROUP OBJECTS { radiusDynAuthClientDisconInvalidServerAddresses, radiusDynAuthClientCoAInvalidServerAddresses, radiusDynAuthServerAddressType, radiusDynAuthServerAddress, radiusDynAuthServerClientPortNumber, radiusDynAuthServerID, radiusDynAuthClientRoundTripTime, radiusDynAuthClientDisconRequests, radiusDynAuthClientDisconRetransmissions, radiusDynAuthClientDisconAcks, radiusDynAuthClientDisconNaks, radiusDynAuthClientMalformedDisconResponses, radiusDynAuthClientDisconBadAuthenticators, radiusDynAuthClientDisconPendingRequests, radiusDynAuthClientDisconTimeouts, radiusDynAuthClientDisconPacketsDropped, radiusDynAuthClientCoARequests, radiusDynAuthClientCoARetransmissions, radiusDynAuthClientCoAAcks, radiusDynAuthClientCoANaks, radiusDynAuthClientMalformedCoAResponses, radiusDynAuthClientCoABadAuthenticators, radiusDynAuthClientCoAPendingRequests, radiusDynAuthClientCoATimeouts, radiusDynAuthClientCoAPacketsDropped, radiusDynAuthClientUnknownTypes, radiusDynAuthClientCounterDiscontinuity } STATUS current DESCRIPTION "The collection of objects providing management of a RADIUS Dynamic Authorization Client." ::= { radiusDynAuthClientMIBGroups 1 } radiusDynAuthClientAuthOnlyGroup OBJECT-GROUP OBJECTS { radiusDynAuthClientDisconAuthOnlyRequests, radiusDynAuthClientDisconNakAuthOnlyRequest, radiusDynAuthClientCoAAuthOnlyRequest, radiusDynAuthClientCoANakAuthOnlyRequest } STATUS current DESCRIPTION "The collection of objects supporting the RADIUS messages including Service-Type attribute with value 'Authorize Only'." ::= { radiusDynAuthClientMIBGroups 2 } radiusDynAuthClientNoSessGroup OBJECT-GROUP OBJECTS { radiusDynAuthClientDisconNakSessNoContext, radiusDynAuthClientCoANakSessNoContext } STATUS current DESCRIPTION "The collection of objects supporting the RADIUS messages that are referring to non-existing sessions." ::= { radiusDynAuthClientMIBGroups 3 } END