RSERPOOL-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, experimental, TimeTicks, Unsigned32 FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF InetAddressType, InetAddress, InetPortNumber FROM INET-ADDRESS-MIB; -- ## Module definition ########################################### rserpoolMIB MODULE-IDENTITY LAST-UPDATED "200904070000Z" -- April 07, 2009 ORGANIZATION "IEM-TdR, UNIVERSITY OF DUISBURG-ESSEN" CONTACT-INFO " THOMAS-DREIBHOLZ Postal: University of Duisburg-Essen Institute for Experimental Mathematics Ellernstrasse 29 D-45326 Essen Germany Phone: +49-201-183-7637 Fax: +49-201-183-7673 Email: [email protected] JAIWANT-MULIK Postal: Delaware State University CIS Department 1200 N. DuPont Hw Dover, DE USA 19904 Phone: +1-302-857-7910 Fax: +1-302-857-6552 Email: [email protected]" DESCRIPTION "The MIB module for managing an RSerPool implementation. Copyright (c) 2009 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. - Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. - Neither the name of Internet Society, IETF or IETF Trust, nor the names of specific contributors, may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This version of this MIB module is part of RFC 5525; see the RFC itself for full legal notices." REVISION "200904070000Z" -- April 07, 2009 DESCRIPTION "This version of the MIB module is published as RFC 5525" ::= { experimental 125 } -- ## RSerPool type definitions ################################### RSerPoolENRPServerIdentifierTC ::= TEXTUAL-CONVENTION DISPLAY-HINT "x" STATUS current DESCRIPTION "The ID of an ENRP server" SYNTAX Unsigned32 (1..4294967295) RSerPoolOperationScopeTC ::= TEXTUAL-CONVENTION DISPLAY-HINT "1024t" STATUS current DESCRIPTION "The ID of an operation scope" SYNTAX OCTET STRING (SIZE (0..65535)) RSerPoolPoolHandleTC ::= TEXTUAL-CONVENTION DISPLAY-HINT "1024t" STATUS current DESCRIPTION "The pool handle" SYNTAX OCTET STRING (SIZE (0..65535)) RserpoolPoolElementIdentifierTC ::= TEXTUAL-CONVENTION DISPLAY-HINT "x" STATUS current DESCRIPTION "The pool element ID" SYNTAX Unsigned32 (1..4294967295) RSerPoolPolicyIdentifierTC ::= TEXTUAL-CONVENTION DISPLAY-HINT "x" STATUS current DESCRIPTION "The ID of the pool policy" SYNTAX Unsigned32 (1..4294967295) RSerPoolPolicyLoadTC ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The load status of a pool element" SYNTAX Unsigned32 (0..4294967295) RSerPoolPolicyWeightTC ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The weight of a pool element" SYNTAX Unsigned32 (0..4294967295) RSerPoolTransportUseTypeTC ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The transport use of a pool element" SYNTAX INTEGER { dataOnly(0), dataPlusControl(1) } RSerPoolOpaqueAddressTC ::= TEXTUAL-CONVENTION DISPLAY-HINT "1024t" STATUS current DESCRIPTION "Opaque address" SYNTAX OCTET STRING (SIZE (0..65535)) -- ## Top-level definitions ####################################### rserpoolMIBObjects OBJECT IDENTIFIER ::= { rserpoolMIB 1 } rserpoolMIBConformance OBJECT IDENTIFIER ::= { rserpoolMIB 2 } rserpoolENRPServers OBJECT IDENTIFIER ::= { rserpoolMIBObjects 1 } rserpoolPoolElements OBJECT IDENTIFIER ::= { rserpoolMIBObjects 2 } rserpoolPoolUsers OBJECT IDENTIFIER ::= { rserpoolMIBObjects 3 } -- ################################################################ -- #### ENRP Servers Section #### -- ################################################################ -- ## Definition of the ENRP server table ######################### rserpoolENRPTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolENRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table listing of ENRP servers." ::= { rserpoolENRPServers 1 } rserpoolENRPEntry OBJECT-TYPE SYNTAX RserpoolENRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An ENRP server entry in the table listing of ENRP servers." INDEX { rserpoolENRPIndex } ::= { rserpoolENRPTable 1 } RserpoolENRPEntry ::= SEQUENCE { rserpoolENRPIndex Unsigned32, rserpoolENRPOperationScope RSerPoolOperationScopeTC, rserpoolENRPIdentifier RSerPoolENRPServerIdentifierTC, rserpoolENRPDescription OCTET STRING, rserpoolENRPUptime TimeTicks, rserpoolENRPPort InetPortNumber, rserpoolENRPASAPAnnouncePort InetPortNumber, rserpoolENRPASAPAnnounceAddrType InetAddressType, rserpoolENRPASAPAnnounceAddr InetAddress, rserpoolENRPENRPAnnouncePort InetPortNumber, rserpoolENRPENRPAnnounceAddrType InetAddressType, rserpoolENRPENRPAnnounceAddr InetAddress } rserpoolENRPIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An integer to uniquely identify an ENRP server." ::= { rserpoolENRPEntry 1 } rserpoolENRPOperationScope OBJECT-TYPE SYNTAX RSerPoolOperationScopeTC MAX-ACCESS read-only STATUS current DESCRIPTION "The definition of the operation scope of this ENRP server." REFERENCE "Section 1.2 of RFC 3237 defines the term operation scope." ::= { rserpoolENRPEntry 2 } rserpoolENRPIdentifier OBJECT-TYPE SYNTAX RSerPoolENRPServerIdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The ENRP server identifier of this ENRP server." REFERENCE "Section 3.1 of RFC 5351 explains the ENRP server identifier." ::= { rserpoolENRPEntry 3 } rserpoolENRPDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "A textual description of this ENRP server, e.g., its location and a contact address of its administrator. This object SHOULD be maintained in a persistent manner." ::= { rserpoolENRPEntry 4 } rserpoolENRPUptime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The ENRP service uptime of this ENRP server." ::= { rserpoolENRPEntry 5 } rserpoolENRPPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The Stream Control Transmission Protocol (SCTP) port number of the ENRP protocol endpoint of this ENRP server." REFERENCE "RFC 5353 defines the ENRP protocol." ::= { rserpoolENRPEntry 6 } rserpoolENRPASAPAnnouncePort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The destination UDP port number to which ASAP multicast announce messages are sent." REFERENCE "Section 3.2 of RFC 5351 explains the server-discovery mechanism using ASAP announces." ::= { rserpoolENRPEntry 7 } rserpoolENRPASAPAnnounceAddrType OBJECT-TYPE SYNTAX InetAddressType { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The network-layer protocol over which ASAP multicast announce messages are sent." REFERENCE "Section 3.2 of RFC 5351 explains the server-discovery mechanism using ASAP announces." ::= { rserpoolENRPEntry 8 } rserpoolENRPASAPAnnounceAddr OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP multicast address to which ASAP multicast announce messages are sent. The type of this address is given in rserpoolENRPASAPAnnounceAddrType." REFERENCE "Section 3.2 of RFC 5351 explains the server-discovery mechanism using ASAP announces." ::= { rserpoolENRPEntry 9 } rserpoolENRPENRPAnnouncePort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The destination UDP port number to which ENRP multicast announce messages are sent." REFERENCE "Section 3.1 of RFC 5353 explains the ENRP multicast announce mechanism." ::= { rserpoolENRPEntry 10 } rserpoolENRPENRPAnnounceAddrType OBJECT-TYPE SYNTAX InetAddressType { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The network-layer protocol over which ENRP multicast announce messages are sent." REFERENCE "Section 3.1 of RFC 5353 explains the ENRP multicast announce mechanism." ::= { rserpoolENRPEntry 11 } rserpoolENRPENRPAnnounceAddr OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination multicast IP address to which ENRP multicast announce messages are sent. The type of this address is given in rserpoolENRPENRPAnnounceAddrType." REFERENCE "Section 3.1 of RFC 5353 explains the ENRP multicast announce mechanism." ::= { rserpoolENRPEntry 12 } -- ## Definition of the pool table ################################ rserpoolENRPPoolTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolENRPPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table listing of pools." ::= { rserpoolENRPServers 3 } rserpoolENRPPoolEntry OBJECT-TYPE SYNTAX RserpoolENRPPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The pool entry in the table listing of pools." INDEX { rserpoolENRPIndex, rserpoolENRPPoolIndex } ::= { rserpoolENRPPoolTable 1 } RserpoolENRPPoolEntry ::= SEQUENCE { rserpoolENRPPoolIndex Unsigned32, rserpoolENRPPoolHandle RSerPoolPoolHandleTC } rserpoolENRPPoolIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An integer to uniquely identify a pool." ::= { rserpoolENRPPoolEntry 1 } rserpoolENRPPoolHandle OBJECT-TYPE SYNTAX RSerPoolPoolHandleTC MAX-ACCESS read-only STATUS current DESCRIPTION "The pool handle of this pool." REFERENCE "Section 1.2 of RFC 3237 defines the term pool handle." ::= { rserpoolENRPPoolEntry 2 } -- ## Definition of the pool element table ######################## rserpoolENRPPoolElementTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolENRPPoolElementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table listing of pool elements." ::= { rserpoolENRPServers 4 } rserpoolENRPPoolElementEntry OBJECT-TYPE SYNTAX RserpoolENRPPoolElementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A pool element in the table listing of pool elements." INDEX { rserpoolENRPIndex, rserpoolENRPPoolIndex, rserpoolENRPPoolElementIndex } ::= { rserpoolENRPPoolElementTable 1 } RserpoolENRPPoolElementEntry ::= SEQUENCE { rserpoolENRPPoolElementIndex Unsigned32, rserpoolENRPPoolElementID RserpoolPoolElementIdentifierTC, rserpoolENRPASAPTransportPort InetPortNumber, rserpoolENRPUserTransportProto Unsigned32, rserpoolENRPUserTransportPort InetPortNumber, rserpoolENRPUserTransportUse RSerPoolTransportUseTypeTC, rserpoolENRPPolicyID RSerPoolPolicyIdentifierTC, rserpoolENRPPolicyDescription OCTET STRING, rserpoolENRPPolicyWeight RSerPoolPolicyWeightTC, rserpoolENRPPolicyLoad RSerPoolPolicyLoadTC, rserpoolENRPPolicyLoadDeg RSerPoolPolicyLoadTC, rserpoolENRPRegistrationLife TimeTicks, rserpoolENRPHomeENRPServer RSerPoolENRPServerIdentifierTC } rserpoolENRPPoolElementIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An integer to uniquely identify a pool element. Note, that uniqueness of a pool element identifier in the pool is not enforced; therefore, this index is required here!" ::={ rserpoolENRPPoolElementEntry 1 } rserpoolENRPPoolElementID OBJECT-TYPE SYNTAX RserpoolPoolElementIdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The pool element identifier of this pool element." REFERENCE "Section 2.2 of RFC 5351 explains the pool element identifier usage." ::={ rserpoolENRPPoolElementEntry 2 } rserpoolENRPASAPTransportPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The SCTP port number of the ASAP endpoint of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of which the port number is given here." ::= { rserpoolENRPPoolElementEntry 3 } rserpoolENRPUserTransportProto OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The transport protocol number of the service endpoint of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the transport protocol number is given here." ::= { rserpoolENRPPoolElementEntry 4 } rserpoolENRPUserTransportPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The transport protocol's port number of the service endpoint of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the port number is given here." ::= { rserpoolENRPPoolElementEntry 5 } rserpoolENRPUserTransportUse OBJECT-TYPE SYNTAX RSerPoolTransportUseTypeTC MAX-ACCESS read-only STATUS current DESCRIPTION "The transport use of the service endpoint of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the transport use is given here." ::= { rserpoolENRPPoolElementEntry 6 } rserpoolENRPPolicyID OBJECT-TYPE SYNTAX RSerPoolPolicyIdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The pool policy of this pool element." REFERENCE "Section 3.8 of RFC 5354 defines the Member Selection Policy Parameter of which the policy identifier is given here." ::= { rserpoolENRPPoolElementEntry 7 } rserpoolENRPPolicyDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The textual description of the pool policy of this pool element." ::= { rserpoolENRPPoolElementEntry 8 } rserpoolENRPPolicyWeight OBJECT-TYPE SYNTAX RSerPoolPolicyWeightTC MAX-ACCESS read-only STATUS current DESCRIPTION "The pool policy's weight parameter for this pool element." REFERENCE "Section 3.8 of RFC 5354 defines the Member Selection Policy Parameter of which the policy's weight parameter is given here." ::= { rserpoolENRPPoolElementEntry 9 } rserpoolENRPPolicyLoad OBJECT-TYPE SYNTAX RSerPoolPolicyLoadTC MAX-ACCESS read-only STATUS current DESCRIPTION "The pool policy's load status for this pool element." REFERENCE "Section 3.8 of RFC 5354 defines the Member Selection Policy Parameter of which the policy's load parameter is given here." ::= { rserpoolENRPPoolElementEntry 10 } rserpoolENRPPolicyLoadDeg OBJECT-TYPE SYNTAX RSerPoolPolicyLoadTC MAX-ACCESS read-only STATUS current DESCRIPTION "The pool policy's load degradation parameter for this pool element." REFERENCE "Section 3.8 of RFC 5354 defines the Member Selection Policy Parameter of which the policy's load degradation parameter is given here." ::= { rserpoolENRPPoolElementEntry 11 } rserpoolENRPRegistrationLife OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The registration life of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the Registration Life." ::= { rserpoolENRPPoolElementEntry 12 } rserpoolENRPHomeENRPServer OBJECT-TYPE SYNTAX RSerPoolENRPServerIdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The ID of the Home ENRP server of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the Home ENRP Server Identifier." ::= { rserpoolENRPPoolElementEntry 13 } -- ## Definition of the ASAP transport address list table ######### rserpoolENRPASAPAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolENRPASAPAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table listing of all IP addresses of the ASAP transport endpoint." REFERENCE "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of which the addresses are listed in this table." ::= { rserpoolENRPServers 5 } rserpoolENRPASAPAddrTableEntry OBJECT-TYPE SYNTAX RserpoolENRPASAPAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IP address of the ASAP transport endpoint." REFERENCE "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of which an address is contained by this entry." INDEX { rserpoolENRPIndex, rserpoolENRPPoolIndex, rserpoolENRPPoolElementIndex, rserpoolENRPASAPAddrTableIndex } ::= { rserpoolENRPASAPAddrTable 1 } RserpoolENRPASAPAddrTableEntry ::= SEQUENCE { rserpoolENRPASAPAddrTableIndex Unsigned32, rserpoolENRPASAPL3Type InetAddressType, rserpoolENRPASAPL3Addr InetAddress } rserpoolENRPASAPAddrTableIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique identifier for the IP address of an ASAP transport endpoint." ::= { rserpoolENRPASAPAddrTableEntry 1 } rserpoolENRPASAPL3Type OBJECT-TYPE SYNTAX InetAddressType { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The network-layer protocol (IPv4 or IPv6) of an IP address of an ASAP transport endpoint." REFERENCE "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of which the network-layer protocol number is given here." ::= { rserpoolENRPASAPAddrTableEntry 2 } rserpoolENRPASAPL3Addr OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of an ASAP transport endpoint. The type of this address is given in rserpoolENRPASAPL3Type." REFERENCE "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of which the network-layer address (IPv4 or IPv6) is given here." ::= { rserpoolENRPASAPAddrTableEntry 3 } -- ## Definition of the user transport address list table ######### rserpoolENRPUserAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolENRPUserAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table listing of all IP addresses of the user transport endpoint." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the addresses are listed in this table." ::= { rserpoolENRPServers 6 } rserpoolENRPUserAddrTableEntry OBJECT-TYPE SYNTAX RserpoolENRPUserAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IP address of the user transport endpoint." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which an address is contained by this entry." INDEX { rserpoolENRPIndex, rserpoolENRPPoolIndex, rserpoolENRPPoolElementIndex, rserpoolENRPUserAddrTableIndex } ::= { rserpoolENRPUserAddrTable 1 } RserpoolENRPUserAddrTableEntry ::= SEQUENCE { rserpoolENRPUserAddrTableIndex Unsigned32, rserpoolENRPUserL3Type InetAddressType, rserpoolENRPUserL3Addr InetAddress, rserpoolENRPUserL3Opaque RSerPoolOpaqueAddressTC } rserpoolENRPUserAddrTableIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique identifier for the IP address of a user transport endpoint." ::= { rserpoolENRPUserAddrTableEntry 1 } rserpoolENRPUserL3Type OBJECT-TYPE SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The network-layer protocol (IPv4 or IPv6) of an IP address of a user transport endpoint. Set to unknown for an opaque address." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the network-layer protocol number is given here." ::= { rserpoolENRPUserAddrTableEntry 2 } rserpoolENRPUserL3Addr OBJECT-TYPE SYNTAX InetAddress (SIZE(0|4|16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of a user transport endpoint. The type of this address is given in rserpoolENRPUserL3Type." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the network-layer address (IPv4 or IPv6) is given here." ::= { rserpoolENRPUserAddrTableEntry 3 } rserpoolENRPUserL3Opaque OBJECT-TYPE SYNTAX RSerPoolOpaqueAddressTC MAX-ACCESS read-only STATUS current DESCRIPTION "The opaque address of a user transport endpoint." REFERENCE "Section 3.16 of RFC 5354 defines the opaque transport address." ::= { rserpoolENRPUserAddrTableEntry 4 } -- ## Definition of ENRP address list table ####################### rserpoolENRPENRPAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolENRPENRPAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table listing of all IP addresses of the ENRP transport endpoint." ::= { rserpoolENRPServers 7 } rserpoolENRPENRPAddrTableEntry OBJECT-TYPE SYNTAX RserpoolENRPENRPAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IP address of the ENRP transport endpoint." INDEX { rserpoolENRPIndex, rserpoolENRPENRPAddrTableIndex } ::= { rserpoolENRPENRPAddrTable 1 } RserpoolENRPENRPAddrTableEntry ::= SEQUENCE { rserpoolENRPENRPAddrTableIndex Unsigned32, rserpoolENRPENRPL3Type InetAddressType, rserpoolENRPENRPL3Addr InetAddress } rserpoolENRPENRPAddrTableIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique identifier for the IP address of an ENRP transport endpoint." ::= { rserpoolENRPENRPAddrTableEntry 1 } rserpoolENRPENRPL3Type OBJECT-TYPE SYNTAX InetAddressType { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The network-layer protocol (IPv4 or IPv6) of an IP address of an ENRP transport endpoint." REFERENCE "RFC 5353 defines the ENRP protocol." ::= { rserpoolENRPENRPAddrTableEntry 2 } rserpoolENRPENRPL3Addr OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of an ENRP transport endpoint. The type of this address is given in rserpoolENRPENRPL3Type." REFERENCE "RFC 5353 defines the ENRP protocol." ::= { rserpoolENRPENRPAddrTableEntry 3 } -- ## Definition of peer table #################################### rserpoolENRPPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolENRPPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table listing of a peer table." ::= { rserpoolENRPServers 8 } rserpoolENRPPeerEntry OBJECT-TYPE SYNTAX RserpoolENRPPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A peer entry in the table listing of a peer table." INDEX { rserpoolENRPPeerIndex } ::= { rserpoolENRPPeerTable 1 } RserpoolENRPPeerEntry ::= SEQUENCE { rserpoolENRPPeerIndex Unsigned32, rserpoolENRPPeerIdentifier RSerPoolENRPServerIdentifierTC, rserpoolENRPPeerPort InetPortNumber, rserpoolENRPPeerLastHeard TimeTicks } rserpoolENRPPeerIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique identifier for a peer entry in the table listing of a peer table." ::= { rserpoolENRPPeerEntry 1 } rserpoolENRPPeerIdentifier OBJECT-TYPE SYNTAX RSerPoolENRPServerIdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The ENRP identifier of this peer." REFERENCE "RFC 5353 explains the usage of the ENRP server identifier." ::= { rserpoolENRPPeerEntry 2 } rserpoolENRPPeerPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The SCTP port number of the ENRP transport endpoint of this peer." REFERENCE "RFC 5353 defines the ENRP protocol." ::= { rserpoolENRPPeerEntry 3 } rserpoolENRPPeerLastHeard OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time since the reception of the last ENRP Presence message of this peer." REFERENCE "Section 4.1 of RFC 5353 defines the last heard value." ::= { rserpoolENRPPeerEntry 4 } -- ## Definition of peer address list table ####################### rserpoolENRPPeerAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolENRPPeerAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table listing of the peer endpoint addresses." ::= { rserpoolENRPServers 9 } rserpoolENRPPeerAddrTableEntry OBJECT-TYPE SYNTAX RserpoolENRPPeerAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table listing of all IP addresses of the ENRP transport endpoint of a peer referenced by rserpoolENRPPeerIndex." INDEX { rserpoolENRPPeerIndex, rserpoolENRPPeerAddrTableIndex } ::= { rserpoolENRPPeerAddrTable 1 } RserpoolENRPPeerAddrTableEntry ::= SEQUENCE { rserpoolENRPPeerAddrTableIndex Unsigned32, rserpoolENRPPeerL3Type InetAddressType, rserpoolENRPPeerL3Addr InetAddress } rserpoolENRPPeerAddrTableIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique identifier for the IP address of a peer ENRP transport endpoint." ::= { rserpoolENRPPeerAddrTableEntry 1 } rserpoolENRPPeerL3Type OBJECT-TYPE SYNTAX InetAddressType { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The network-layer protocol (IPv4 or IPv6) of an IP address of a peer ENRP transport endpoint." REFERENCE "RFC 5353 defines the ENRP protocol." ::= { rserpoolENRPPeerAddrTableEntry 2 } rserpoolENRPPeerL3Addr OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of a peer ENRP transport endpoint. The type of this address is given in rserpoolENRPPeerL3Type." REFERENCE "RFC 5353 defines the ENRP protocol." ::= { rserpoolENRPPeerAddrTableEntry 3 } -- ################################################################ -- #### Pool Elements Section #### -- ################################################################ -- ## Definition of the pool element table ######################## rserpoolPETable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolPEEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table listing of pool elements." ::= { rserpoolPoolElements 1 } rserpoolPEEntry OBJECT-TYPE SYNTAX RserpoolPEEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A pool element in the table listing of pool elements." INDEX { rserpoolPEIndex } ::= { rserpoolPETable 1 } RserpoolPEEntry ::= SEQUENCE { rserpoolPEIndex Unsigned32, rserpoolPEOperationScope RSerPoolOperationScopeTC, rserpoolPEPoolHandle RSerPoolPoolHandleTC, rserpoolPEIdentifier RserpoolPoolElementIdentifierTC, rserpoolPEDescription OCTET STRING, rserpoolPEUptime TimeTicks, rserpoolPEASAPTransportPort InetPortNumber, rserpoolPEUserTransportProto Unsigned32, rserpoolPEUserTransportPort InetPortNumber, rserpoolPEUserTransportUse RSerPoolTransportUseTypeTC, rserpoolPEPolicyID RSerPoolPolicyIdentifierTC, rserpoolPEPolicyDescription OCTET STRING, rserpoolPEPolicyWeight RSerPoolPolicyWeightTC, rserpoolPEPolicyLoad RSerPoolPolicyLoadTC, rserpoolPEPolicyLoadDeg RSerPoolPolicyLoadTC, rserpoolPERegistrationLife TimeTicks, rserpoolPEHomeENRPServer RSerPoolENRPServerIdentifierTC } rserpoolPEIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An integer to uniquely identify a pool element. Note, that uniqueness of a pool element identifier in the pool is not enforced; therefore, this index is required here!" ::={ rserpoolPEEntry 1 } rserpoolPEOperationScope OBJECT-TYPE SYNTAX RSerPoolOperationScopeTC MAX-ACCESS read-only STATUS current DESCRIPTION "The operation scope of this pool element." REFERENCE "Section 1.2 of RFC 3237 defines the term operation scope." ::= { rserpoolPEEntry 2 } rserpoolPEPoolHandle OBJECT-TYPE SYNTAX RSerPoolPoolHandleTC MAX-ACCESS read-write STATUS current DESCRIPTION "The pool handle of this pool element. Changing this object will update the pool element's pool handle and result in a re-registration. This object SHOULD be maintained in a persistent manner." REFERENCE "Section 1.2 of RFC 3237 defines the term pool handle." ::={ rserpoolPEEntry 3 } rserpoolPEIdentifier OBJECT-TYPE SYNTAX RserpoolPoolElementIdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The pool element identifier of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the pool element identifier." ::={ rserpoolPEEntry 4 } rserpoolPEDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "A textual description of this pool element, e.g., its location and a contact address of its administrator. This object SHOULD be maintained in a persistent manner." ::= { rserpoolPEEntry 5 } rserpoolPEUptime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The ENRP service uptime of this pool element." ::= { rserpoolPEEntry 6 } rserpoolPEASAPTransportPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The SCTP port number of the ASAP endpoint of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of which the port number is given here." ::= { rserpoolPEEntry 7 } rserpoolPEUserTransportProto OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The transport protocol number of the service endpoint of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the transport protocol number is given here." ::= { rserpoolPEEntry 8 } rserpoolPEUserTransportPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The transport protocol's port number of the service endpoint of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the port number is given here." ::= { rserpoolPEEntry 9 } rserpoolPEUserTransportUse OBJECT-TYPE SYNTAX RSerPoolTransportUseTypeTC MAX-ACCESS read-only STATUS current DESCRIPTION "The transport use of the service endpoint of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the transport use is given here." ::= { rserpoolPEEntry 10 } rserpoolPEPolicyID OBJECT-TYPE SYNTAX RSerPoolPolicyIdentifierTC MAX-ACCESS read-write STATUS current DESCRIPTION "The pool policy of this pool element. Changing this object will update the pool element's policy and result in a re-registration. This object SHOULD be maintained in a persistent manner." REFERENCE "Section 3.8 of RFC 5354 defines the Member Selection Policy Parameter of which the policy identifier is given here." ::= { rserpoolPEEntry 11 } rserpoolPEPolicyDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "The textual description of the pool policy of this pool element. This object SHOULD be maintained in a persistent manner." ::= { rserpoolPEEntry 12 } rserpoolPEPolicyWeight OBJECT-TYPE SYNTAX RSerPoolPolicyWeightTC MAX-ACCESS read-write STATUS current DESCRIPTION "The pool policy's weight parameter for this pool element. Changing this object will update the pool element's policy weight setting and result in a re-registration. This object SHOULD be maintained in a persistent manner." REFERENCE "Section 3.8 of RFC 5354 defines the Member Selection Policy Parameter of which the policy's weight parameter is given here." ::= { rserpoolPEEntry 13 } rserpoolPEPolicyLoad OBJECT-TYPE SYNTAX RSerPoolPolicyLoadTC MAX-ACCESS read-only STATUS current DESCRIPTION "The pool policy's load status for this pool element." REFERENCE "Section 3.8 of RFC 5354 defines the Member Selection Policy Parameter of which the policy's load parameter is given here." ::= { rserpoolPEEntry 14 } rserpoolPEPolicyLoadDeg OBJECT-TYPE SYNTAX RSerPoolPolicyLoadTC MAX-ACCESS read-write STATUS current DESCRIPTION "The pool policy's load degradation parameter for this pool element. Changing this object will update the pool element's load degradation setting and result in a re-registration. This object SHOULD be maintained in a persistent manner." REFERENCE "Section 3.8 of RFC 5354 defines the Member Selection Policy Parameter of which the policy's load degradation parameter is given here." ::= { rserpoolPEEntry 15 } rserpoolPERegistrationLife OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-write STATUS current DESCRIPTION "The registration life of this pool element. Changing this object will update the pool element's lifetime setting and result in a re-registration. This object SHOULD be maintained in a persistent manner." REFERENCE "Section 3.10 of RFC 5354 defines the Registration Life." ::= { rserpoolPEEntry 16 } rserpoolPEHomeENRPServer OBJECT-TYPE SYNTAX RSerPoolENRPServerIdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The ID of the Home ENRP server of this pool element." REFERENCE "Section 3.10 of RFC 5354 defines the Home ENRP Server Identifier." ::= { rserpoolPEEntry 17 } -- ## Definition of the ASAP transport address list table ######### rserpoolPEASAPAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolPEASAPAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table listing of all IP addresses of the ASAP transport endpoint." REFERENCE "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of which the addresses are listed in this table." ::= { rserpoolPoolElements 2 } rserpoolPEASAPAddrTableEntry OBJECT-TYPE SYNTAX RserpoolPEASAPAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IP address of the ASAP transport endpoint." REFERENCE "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of which an address is contained by this entry." INDEX { rserpoolPEIndex, rserpoolPEASAPAddrTableIndex } ::= { rserpoolPEASAPAddrTable 1 } RserpoolPEASAPAddrTableEntry ::= SEQUENCE { rserpoolPEASAPAddrTableIndex Unsigned32, rserpoolPEASAPL3Type InetAddressType, rserpoolPEASAPL3Addr InetAddress } rserpoolPEASAPAddrTableIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique identifier for the IP address of an ASAP transport endpoint." ::= { rserpoolPEASAPAddrTableEntry 1 } rserpoolPEASAPL3Type OBJECT-TYPE SYNTAX InetAddressType { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The network-layer protocol (IPv4 or IPv6) of an IP address of an ASAP transport endpoint." REFERENCE "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of which the network-layer protocol number is given here." ::= { rserpoolPEASAPAddrTableEntry 2 } rserpoolPEASAPL3Addr OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of an ASAP transport endpoint. The type of this address is given in rserpoolPEASAPL3Type." REFERENCE "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of which the network-layer address (IPv4 or IPv6) is given here." ::= { rserpoolPEASAPAddrTableEntry 3 } -- ## Definition of the user transport address list table ######### rserpoolPEUserAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolPEUserAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table listing of all IP addresses of the user transport endpoint." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the addresses are listed in this table." ::= { rserpoolPoolElements 6 } rserpoolPEUserAddrTableEntry OBJECT-TYPE SYNTAX RserpoolPEUserAddrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IP address of the user transport endpoint." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which an address is contained by this entry." INDEX { rserpoolPEIndex, rserpoolPEUserAddrTableIndex } ::= { rserpoolPEUserAddrTable 1 } RserpoolPEUserAddrTableEntry ::= SEQUENCE { rserpoolPEUserAddrTableIndex Unsigned32, rserpoolPEUserL3Type InetAddressType, rserpoolPEUserL3Addr InetAddress, rserpoolPEUserL3Opaque RSerPoolOpaqueAddressTC } rserpoolPEUserAddrTableIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique identifier for the IP address of a user transport endpoint." ::= { rserpoolPEUserAddrTableEntry 1 } rserpoolPEUserL3Type OBJECT-TYPE SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The network-layer protocol of an IP address of a user transport endpoint. Set to unknown for opaque address." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the network-layer protocol number is given here." ::= { rserpoolPEUserAddrTableEntry 2 } rserpoolPEUserL3Addr OBJECT-TYPE SYNTAX InetAddress (SIZE(0|4|16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of a user transport endpoint. The type of this address is given in rserpoolPEUserL3Addr." REFERENCE "Section 3.10 of RFC 5354 defines the User Transport Parameter of which the network-layer address (IPv4 or IPv6) is given here." ::= { rserpoolPEUserAddrTableEntry 3 } rserpoolPEUserL3Opaque OBJECT-TYPE SYNTAX RSerPoolOpaqueAddressTC MAX-ACCESS read-only STATUS current DESCRIPTION "The opaque address of a user transport endpoint." REFERENCE "Section 3.16 of RFC 5354 defines the opaque transport address." ::= { rserpoolPEUserAddrTableEntry 4 } -- ################################################################ -- #### Pool Users Section #### -- ################################################################ -- ## Definition of the pool user table ########################### rserpoolPUTable OBJECT-TYPE SYNTAX SEQUENCE OF RserpoolPUEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table listing of pool users." ::= { rserpoolPoolUsers 1 } rserpoolPUEntry OBJECT-TYPE SYNTAX RserpoolPUEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A pool user in the table listing of pool users." INDEX { rserpoolPUIndex } ::= { rserpoolPUTable 1 } RserpoolPUEntry ::= SEQUENCE { rserpoolPUIndex Unsigned32, rserpoolPUOperationScope RSerPoolOperationScopeTC, rserpoolPUPoolHandle RSerPoolPoolHandleTC, rserpoolPUDescription OCTET STRING, rserpoolPUUptime TimeTicks } rserpoolPUIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An integer to uniquely identify a pool user." ::= { rserpoolPUEntry 1 } rserpoolPUOperationScope OBJECT-TYPE SYNTAX RSerPoolOperationScopeTC MAX-ACCESS read-only STATUS current DESCRIPTION "The operation scope of this pool user." REFERENCE "Section 1.2 of RFC 3237 defines the term operation scope." ::= { rserpoolPUEntry 2 } rserpoolPUPoolHandle OBJECT-TYPE SYNTAX RSerPoolPoolHandleTC MAX-ACCESS read-write STATUS current DESCRIPTION "The pool handle of this pool user. Changing this object will update the pool user's pool handle for all future sessions. This object SHOULD be maintained in a persistent manner." REFERENCE "Section 1.2 of RFC 3237 defines the term pool handle." ::={ rserpoolPUEntry 3 } rserpoolPUDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "A textual description of this pool user, e.g., its location and a contact address of its administrator. This object SHOULD be maintained in a persistent manner." ::= { rserpoolPUEntry 4 } rserpoolPUUptime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The ENRP service uptime of this pool user." ::= { rserpoolPUEntry 5 } -- ## MIB conformance and compliance ############################## rserpoolMIBCompliances OBJECT IDENTIFIER ::= { rserpoolMIBConformance 1 } rserpoolMIBGroups OBJECT IDENTIFIER ::= { rserpoolMIBConformance 2 } rserpoolMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement RSerPool." MODULE MANDATORY-GROUPS { rserpoolENRPGroup, rserpoolPEGroup, rserpoolPUGroup } ::= { rserpoolMIBCompliances 1 } rserpoolENRPGroup OBJECT-GROUP OBJECTS { rserpoolENRPOperationScope, rserpoolENRPIdentifier, rserpoolENRPDescription, rserpoolENRPUptime, rserpoolENRPPort, rserpoolENRPASAPAnnouncePort, rserpoolENRPASAPAnnounceAddr, rserpoolENRPASAPAnnounceAddrType, rserpoolENRPENRPAnnounceAddrType, rserpoolENRPENRPAnnouncePort, rserpoolENRPENRPAnnounceAddr, rserpoolENRPPoolHandle, rserpoolENRPPoolElementID, rserpoolENRPASAPTransportPort, rserpoolENRPUserTransportProto, rserpoolENRPUserTransportUse, rserpoolENRPUserTransportPort, rserpoolENRPPolicyID, rserpoolENRPPolicyDescription, rserpoolENRPPolicyWeight, rserpoolENRPPolicyLoad, rserpoolENRPPolicyLoadDeg, rserpoolENRPRegistrationLife, rserpoolENRPHomeENRPServer, rserpoolENRPASAPL3Type, rserpoolENRPASAPL3Addr, rserpoolENRPUserL3Type, rserpoolENRPUserL3Addr, rserpoolENRPUserL3Opaque, rserpoolENRPENRPL3Type, rserpoolENRPENRPL3Addr, rserpoolENRPPeerIdentifier, rserpoolENRPPeerPort, rserpoolENRPPeerLastHeard, rserpoolENRPPeerL3Type, rserpoolENRPPeerL3Addr } STATUS current DESCRIPTION "The group contains all ENRP server instances running on the system" ::= { rserpoolMIBGroups 1 } rserpoolPEGroup OBJECT-GROUP OBJECTS { rserpoolPEOperationScope, rserpoolPEPoolHandle, rserpoolPEIdentifier, rserpoolPEDescription, rserpoolPEUptime, rserpoolPEASAPTransportPort, rserpoolPEUserTransportProto, rserpoolPEUserTransportPort, rserpoolPEUserTransportUse, rserpoolPEPolicyID, rserpoolPEPolicyDescription, rserpoolPEPolicyWeight, rserpoolPEPolicyLoad, rserpoolPEPolicyLoadDeg, rserpoolPERegistrationLife, rserpoolPEHomeENRPServer, rserpoolPEASAPL3Type, rserpoolPEASAPL3Addr, rserpoolPEUserL3Type, rserpoolPEUserL3Addr, rserpoolPEUserL3Opaque } STATUS current DESCRIPTION "The group contains all pool element instances running on the system" ::= { rserpoolMIBGroups 2 } rserpoolPUGroup OBJECT-GROUP OBJECTS { rserpoolPUOperationScope, rserpoolPUPoolHandle, rserpoolPUDescription, rserpoolPUUptime } STATUS current DESCRIPTION "The group contains all pool user instances running on the system" ::= { rserpoolMIBGroups 3 } END