TED-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, transmission, NOTIFICATION-TYPE FROM SNMPv2-SMI -- RFC 2578 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC 2580 TEXTUAL-CONVENTION, RowPointer FROM SNMPv2-TC -- RFC 2579 IANAGmplsLSPEncodingTypeTC, IANAGmplsSwitchingTypeTC FROM IANA-GMPLS-TC-MIB -- RFC 4802 InetAddress, InetAddressType FROM INET-ADDRESS-MIB -- RFC 4001 Float32TC FROM FLOAT-TC-MIB -- RFC 6340 ; tedMIB MODULE-IDENTITY LAST-UPDATED "201212210000Z" -- 21 Dec. 2012 00:00:00 GMT ORGANIZATION "IETF CCAMP Working Group." CONTACT-INFO " Tomohiro Otani [email protected] Masanori Miyazawa [email protected] Thomas D. Nadeau [email protected] Kenji Kumaki [email protected] Comments and discussion to [email protected]" DESCRIPTION "This MIB module contains managed object definitions for TED in support of MPLS/GMPLS TE Database. Copyright (c) 2013 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info)." -- Revision history. REVISION "201212210000Z" -- 21 Dec. 2012 00:00:00 GMT DESCRIPTION "Initial version. Published as RFC 6825." ::= { transmission 273 } -- assigned by IANA; see Section 9 for details. -- Textual Conventions. TedAreaIdTC ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The area identifier of the IGP. If OSPF is used to advertise LSA, this represents an ospfArea. If IS-IS is used, this represents an area address." SYNTAX OCTET STRING (SIZE (0..20)) TedRouterIdTC ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The router identifier. If OSPF is used to advertise LSA, this represents a Router ID. If IS-IS is used, this represents a System ID." SYNTAX OCTET STRING (SIZE (0..6)) TedLinkIndexTC ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The link identifier. If OSPF is used, this represents an ospfLsdbID. If IS-IS is used, this represents an isisLSPID. If a locally configured link is used, this object represents an arbitrary value, which is locally defined in a router." SYNTAX OCTET STRING (SIZE (0..8)) -- Top-level components of this MIB module. tedNotifications OBJECT IDENTIFIER ::= { tedMIB 0 } tedObjects OBJECT IDENTIFIER ::= { tedMIB 1 } tedConformance OBJECT IDENTIFIER ::= { tedMIB 2 } -- TED Table tedTable OBJECT-TYPE SYNTAX SEQUENCE OF TedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates multiple TED information, which has been supported by RFC 3630 and RFC 5305." ::= { tedObjects 1 } tedEntry OBJECT-TYPE SYNTAX TedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains TED information commonly utilized in both MPLS and GMPLS." INDEX { tedLocalRouterId, tedRemoteRouterId, tedLinkInformationSource, tedLinkIndex } ::= { tedTable 1 } TedEntry ::= SEQUENCE { tedLinkInformationSource INTEGER, tedLocalRouterId TedRouterIdTC, tedRemoteRouterId TedRouterIdTC, tedLinkIndex TedLinkIndexTC, tedLinkInformationData RowPointer, tedLinkState INTEGER, tedAreaId TedAreaIdTC, tedLinkType INTEGER, tedTeRouterIdAddrType InetAddressType, tedTeRouterIdAddr InetAddress, tedLinkIdAddrType InetAddressType, tedLinkIdAddr InetAddress, tedMetric Integer32, tedMaxBandwidth Float32TC, tedMaxReservableBandwidth Float32TC, tedUnreservedBandwidthPri0 Float32TC, tedUnreservedBandwidthPri1 Float32TC, tedUnreservedBandwidthPri2 Float32TC, tedUnreservedBandwidthPri3 Float32TC, tedUnreservedBandwidthPri4 Float32TC, tedUnreservedBandwidthPri5 Float32TC, tedUnreservedBandwidthPri6 Float32TC, tedUnreservedBandwidthPri7 Float32TC, tedAdministrativeGroup Integer32, tedLocalId Integer32, tedRemoteId Integer32, tedLinkProtectionType BITS } tedLinkInformationSource OBJECT-TYPE SYNTAX INTEGER { unknown(0), locallyConfigured(1), ospfv2(2), ospfv3(3), isis(4), other(5) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the source of the information about the TE link." ::= { tedEntry 1 } tedLocalRouterId OBJECT-TYPE SYNTAX TedRouterIdTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the Router ID of the router originating the LSA. If OSPF is used to advertise LSA, this represents a Router ID. If IS-IS is used, this represents a System ID. Otherwise, this represents zero." REFERENCE "OSPF Version 2, RFC 2328, Appendix C.1 OSPF for IPv6, RFC 5340, Appendix C.1 ISO10589, Section 7.1" ::= { tedEntry 2 } tedRemoteRouterId OBJECT-TYPE SYNTAX TedRouterIdTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the router at the remote end of the link from the originating router. If OSPF is used to advertise LSA, this represents a Link ID in the Link TLV. If IS-IS is used, this represents a neighbor System ID defined in RFC 5305. Otherwise, this represents zero." REFERENCE "OSPF Version 2, RFC 2328, Appendix C.1 OSPF for IPv6, RFC 5340, Appendix C.1 ISO10589, Section 7.1" ::= { tedEntry 3 } tedLinkIndex OBJECT-TYPE SYNTAX TedLinkIndexTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the link state identifier. If OSPF is used, this represents an ospfLsdbID. If IS-IS is used, this represents an isisLSPID. Otherwise, this represents a unique identifier within a node." REFERENCE "OSPF Version 2, RFC 2328, Appendix A.4.1, OSPF for IPv6, RFC 5340, Appendix A.4.2 ISO10589, Section 9.8 " ::= { tedEntry 4 } tedLinkInformationData OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "If tedLinkInformationSource has the value unknown(0), this object MUST contain a value of zeroDotZero. If tedLinkInformationSource has the value locallyConfigured(1), an implementation can use this object to supply the identifier of the corresponding row entry in the teLinkTable of TE-LINK- STD-MIB (RFC 4220), the identifier of the corresponding row in a local proprietary TE link MIB module, or the value of zeroDotZero. If tedLinkInformationSource has the value ospfv2(2) and ospfv3(3), an implementation can use this object to supply the identifier of the corresponding row entry in the ospfLocalLsdbTable (OSPFv2-MIB) and the ospfv3AreaLsdbTable (OSPFv3-MIB), or the value of zeroDotZero. If tedLinkInformationSource has the value isis(4), an implementation can use this object to supply the identifier of the corresponding row entry in the isisAreaAddr of ISIS-MIB (RFC 4444), or the value of zeroDotZero. If tedLinkInformationSource has the value other(5), an implementation can use this object to supply the identifier of the corresponding row entry in the local proprietary MIB module, or the value of zeroDotZero." ::= { tedEntry 5 } tedLinkState OBJECT-TYPE SYNTAX INTEGER { unknown (0), up (1), down (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the actual operational state of this TE link. For instance, if a row is created in the TED table, but the actual TE link is not available for some reason (e.g., when there is not yet a physical link or the link has been manually disabled), then the object would be down(2) state. In contrast, if a row is added and the TE link is available, this would be operationally up(1)." ::= { tedEntry 6 } tedAreaId OBJECT-TYPE SYNTAX TedAreaIdTC MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the area identifier of the IGP. If OSPF is used to advertise LSA, this represents an ospfArea. If IS-IS is used, this represents an area address. Otherwise, this represents zero." REFERENCE "OSPF Version 2, RFC 2328, Appendix C.2 OSPF for IPv6, RFC 5340, Appendix C.2 ISO10589, Section 9.8" ::= { tedEntry 7 } tedLinkType OBJECT-TYPE SYNTAX INTEGER { pointToPoint (1), multiAccess (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the type of the link, such as point to point or multi-access." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.1" ::= { tedEntry 8 } tedTeRouterIdAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the TE-Router ID address type. Only values unknown(0), ipv4(1), or ipv6(2) are supported." ::= { tedEntry 9 } tedTeRouterIdAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the TE-Router ID." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.4.1 IS-IS extensions for TE, RFC 5305, Section 4.3" ::= { tedEntry 10 } tedLinkIdAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the address type of the TE Link ID. Only values unknown(0), ipv4(1), or ipv6(2) are supported." ::= { tedEntry 11 } tedLinkIdAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the Router ID of the neighbor in the case of point-to-point links. This also indicates the interface address of the designated router in the case of multi-access links." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.2 IS-IS extensions for TE, RFC 5305, Section 4.3" ::= { tedEntry 12 } tedMetric OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the traffic engineering metric value of the TE link." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.5 IS-IS extensions for TE, RFC 5305, Section 3.7" ::= { tedEntry 13 } tedMaxBandwidth OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the maximum bandwidth that can be used on this link in this direction." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.6 IS-IS extensions for TE, RFC 5305, Section 3.4" ::= { tedEntry 14 } tedMaxReservableBandwidth OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the maximum bandwidth that may be reserved on this link in this direction." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.7 IS-IS extensions for TE, RFC 5305, Section 3.5" ::= { tedEntry 15 } tedUnreservedBandwidthPri0 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 0." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.8 IS-IS extensions for TE, RFC 5305, Section 3.6" ::= { tedEntry 16 } tedUnreservedBandwidthPri1 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 1." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.8 IS-IS extensions for TE, RFC 5305, Section 3.6" ::= { tedEntry 17 } tedUnreservedBandwidthPri2 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 2." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.8 IS-IS extensions for TE, RFC 5305, Section 3.6" ::= { tedEntry 18 } tedUnreservedBandwidthPri3 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 3." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.8 IS-IS extensions for TE, RFC 5305, Section 3.6" ::= { tedEntry 19 } tedUnreservedBandwidthPri4 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 4." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.8 IS-IS extensions for TE, RFC 5305, Section 3.6" ::= { tedEntry 20 } tedUnreservedBandwidthPri5 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 5." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.8 IS-IS extensions for TE, RFC 5305, Section 3.6" ::= { tedEntry 21 } tedUnreservedBandwidthPri6 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 6." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.8 IS-IS extensions for TE, RFC 5305, 3.6" ::= { tedEntry 22 } tedUnreservedBandwidthPri7 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 7." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.8 IS-IS extensions for TE, RFC 5305, Section 3.6" ::= { tedEntry 23 } tedAdministrativeGroup OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the Administrative Group to which the link belongs. Since the value is a bit mask, the link can belong to multiple groups. This is also called Resource Class/Color." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.9 IS-IS extensions for TE, RFC 5305, Section 3.1" ::= { tedEntry 24 } tedLocalId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the Link Local Identifier of an unnumbered link." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.1 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.1" ::= { tedEntry 25 } tedRemoteId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the Link Remote Identifier of an unnumbered link." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.1 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.1" ::= { tedEntry 26 } tedLinkProtectionType OBJECT-TYPE SYNTAX BITS { extraTraffic(0), unprotected(1), shared (2), dedicatedOneToOne (3), dedicatedOnePlusOne(4), enhanced(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the protection type of the TE link." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.2 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.2" ::= { tedEntry 27 } -- TED Local Interface IP Address Table tedLocalIfAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF TedLocalIfAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the IP address information of a local TE link." ::= { tedObjects 2 } tedLocalIfAddrEntry OBJECT-TYPE SYNTAX TedLocalIfAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains the IP address information of the local TE link." INDEX { tedLinkIndex, tedLocalIfAddr } ::= { tedLocalIfAddrTable 1 } TedLocalIfAddrEntry ::= SEQUENCE { tedLocalIfAddrType InetAddressType, tedLocalIfAddr InetAddress } tedLocalIfAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the address type of the local TE link. Only values unknown(0), ipv4(1), or ipv6(2) have to be supported." ::= { tedLocalIfAddrEntry 1 } tedLocalIfAddr OBJECT-TYPE SYNTAX InetAddress (SIZE (1..20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the address of the local TE link." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.3, Traffic Engineering Extensions to OSPF Version 3, RFC 5329, Section 4.3 IS-IS extensions for TE, RFC 5305, Section 3.4" ::= { tedLocalIfAddrEntry 2 } -- TED Remote Interface IP Address Table tedRemoteIfAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF TedRemoteIfAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the IP address information of a remote TE link." ::= { tedObjects 3 } tedRemoteIfAddrEntry OBJECT-TYPE SYNTAX TedRemoteIfAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains the IP address information of the remote TE link." INDEX { tedLinkIndex, tedRemoteIfAddr } ::= { tedRemoteIfAddrTable 1 } TedRemoteIfAddrEntry ::= SEQUENCE { tedRemoteIfAddrType InetAddressType, tedRemoteIfAddr InetAddress } tedRemoteIfAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the address type of the remote TE link." ::= { tedRemoteIfAddrEntry 1 } tedRemoteIfAddr OBJECT-TYPE SYNTAX InetAddress(SIZE (1..20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the address of the remote TE link." REFERENCE "Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, Section 2.5.4, Traffic Engineering Extensions to OSPF Version3, RFC 5329, Section 4.4 IS-IS extensions for TE, RFC 5305, Section 3.3" ::= { tedRemoteIfAddrEntry 2 } -- TED Switching Capability Table tedSwCapTable OBJECT-TYPE SYNTAX SEQUENCE OF TedSwCapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the GMPLS TED switching capability information." ::= { tedObjects 4 } tedSwCapEntry OBJECT-TYPE SYNTAX TedSwCapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry relates each TE link with its GMPLS TE switching capability information. If the MIB module deals with only OSPF- TE information, the value of each object related with GMPLS TE extensions should be null." INDEX { tedLinkIndex, tedSwCapIndex } ::= { tedSwCapTable 1 } TedSwCapEntry ::= SEQUENCE { tedSwCapIndex Unsigned32, tedSwCapType IANAGmplsSwitchingTypeTC, tedSwCapEncoding IANAGmplsLSPEncodingTypeTC, tedSwCapMaxLspBandwidthPri0 Float32TC, tedSwCapMaxLspBandwidthPri1 Float32TC, tedSwCapMaxLspBandwidthPri2 Float32TC, tedSwCapMaxLspBandwidthPri3 Float32TC, tedSwCapMaxLspBandwidthPri4 Float32TC, tedSwCapMaxLspBandwidthPri5 Float32TC, tedSwCapMaxLspBandwidthPri6 Float32TC, tedSwCapMaxLspBandwidthPri7 Float32TC, tedSwCapMinLspBandwidth Float32TC, tedSwCapIfMtu Integer32, tedSwCapIndication INTEGER } tedSwCapIndex OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This index is utilized to identify multiple switching functions on a local or remote TE link according to definitions of textual conventions of GMPLS, RFC 4801." ::= { tedSwCapEntry 1 } tedSwCapType OBJECT-TYPE SYNTAX IANAGmplsSwitchingTypeTC MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the GMPLS switching capability assigned to the TE link according to definitions of textual conventions of GMPLS, RFC 4801." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 2 } tedSwCapEncoding OBJECT-TYPE SYNTAX IANAGmplsLSPEncodingTypeTC MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the GMPLS encoding type assigned to the TE link." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 3 } tedSwCapMaxLspBandwidthPri0 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 0 for GMPLS LSP creation." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 4 } tedSwCapMaxLspBandwidthPri1 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 1 for GMPLS LSP creation." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 5 } tedSwCapMaxLspBandwidthPri2 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 2 for GMPLS LSP creation." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 6 } tedSwCapMaxLspBandwidthPri3 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 3 for GMPLS LSP creation." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 7 } tedSwCapMaxLspBandwidthPri4 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 4 for GMPLS LSP creation." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 8 } tedSwCapMaxLspBandwidthPri5 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 5 for GMPLS LSP creation." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 9 } tedSwCapMaxLspBandwidthPri6 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 6 for GMPLS LSP creation." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 10 } tedSwCapMaxLspBandwidthPri7 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 7 for GMPLS LSP creation." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 11 } tedSwCapMinLspBandwidth OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the minimum bandwidth of the TE link for GMPLS LSP creation if the switching capability field is TDM, PSC-1, PSC-2, PSC-3, or PSC-4." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 12 } tedSwCapIfMtu OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the MTU of the local or remote TE link." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 13 } tedSwCapIndication OBJECT-TYPE SYNTAX INTEGER { standard (0), arbitrary (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the interface supports Standard or Arbitrary SONET/SDH." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.4 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.3" ::= { tedSwCapEntry 14 } -- TED SRLG Table tedSrlgTable OBJECT-TYPE SYNTAX SEQUENCE OF TedSrlgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the SRLG information of the TE link." ::= { tedObjects 5 } tedSrlgEntry OBJECT-TYPE SYNTAX TedSrlgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry relates each TE link with its SRLG information." INDEX { tedLinkIndex, tedSrlgIndex } ::= { tedSrlgTable 1 } TedSrlgEntry ::= SEQUENCE { tedSrlgIndex Unsigned32, tedSrlg Integer32 } tedSrlgIndex OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This index is utilized to identify multiple SRLG values on a local or remote TE link. This object represents an arbitrary value, which is locally defined in a router." REFERENCE "OSPF Extensions in support of GMPLS, RFC 4203, Section 1.3 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.4" ::= { tedSrlgEntry 1 } tedSrlg OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the SRLG value assigned to a local or remote TE link." REFERENCE "OSPF Extensions in Support of GMPLS, RFC 4203, Section 1.3 IS-IS Extensions in Support of GMPLS, RFC 5307, Section 1.4" ::= { tedSrlgEntry 2 } -- Notification Configuration tedStatusChangeNotificationMaxRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "A lot of notifications relating to the status change are expected to generate in a node, especially when a network failure occurs and might cause a performance degradation of the node itself. To avoid such a defect, this object provides the maximum number of notifications generated per minute. If events occur more rapidly, the implementation may simply fail to emit these notifications during that period, or may queue them until an appropriate time. A value of 0 means no throttling is applied and events may be notified at the rate at which they occur." DEFVAL {1} ::= { tedObjects 6 } tedCreatedDeletedNotificationMaxRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "A lot of notifications relating to new registration in the TED table by receiving new TE link information or deletion of existing entries in the TED table are expected to generate in a node. This object provides the maximum number of notifications generated per minute." DEFVAL {1} ::= { tedObjects 7 } -- Notifications tedStatusChange NOTIFICATION-TYPE OBJECTS { tedLinkState } STATUS current DESCRIPTION "This notification signifies that there has been change in the TE information of tedTable, tedLocalIfAddrTable, tedRemoteIfAddrTable, tedSwCapTable, and/or tedSrlgTable. For example, this should be generated when tedUnreservedBandwidth is changed to create or delete LSP using the registered TE link." ::= { tedNotifications 1 } tedEntryCreated NOTIFICATION-TYPE OBJECTS { tedLinkState } STATUS current DESCRIPTION "This notification signifies that there has been new registration in the TED table by receiving new TE link information. For example, this should be generated when a new index (tedLinkIndex) is registered in the TED table." ::= { tedNotifications 2 } tedEntryDeleted NOTIFICATION-TYPE OBJECTS { tedLinkState } STATUS current DESCRIPTION "This notification signifies that there has been deletion of an entry in the TED table. For example, this should be generated when one of the existing entries is deleted in the TED table." ::= { tedNotifications 3 } -- Conformance Statement tedCompliances OBJECT IDENTIFIER ::= { tedConformance 1 } tedGroups OBJECT IDENTIFIER ::= { tedConformance 2 } -- Module Compliance tedModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents provides full support for the TED MIB." MODULE -- this module MANDATORY-GROUPS { tedMainGroup, tedObjectsGroup, tedNotificationGroup } GROUP tedUnnumberedLinkGroup DESCRIPTION "This group is mandatory for TE links that support the unnumbered links." GROUP tedNumberedLinkGroup DESCRIPTION "This group is mandatory for TE links that support the numbered links." GROUP tedSwCapGroup DESCRIPTION "This group is mandatory for TE links that support GMPLS switching capability." GROUP tedSwCapMinLspBandwidthGroup DESCRIPTION "This group is mandatory for TE links if the switching capability field is TDM, PSC-1, PSC-2, PSC-3, or PSC-4." GROUP tedSwCapIfMtuGroup DESCRIPTION "This group is mandatory for TE links that support the MTU of the local or remote TE link." GROUP tedSwCapIndicationGroup DESCRIPTION "This group is mandatory for TE links that support Standard or Arbitrary SONET/SDH." GROUP tedSrlgGroup DESCRIPTION "This group is mandatory for TE links that support SRLG information." ::= { tedCompliances 1 } -- -- ReadOnly Compliance -- tedModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance requirement for implementations only provides read- only support for TED. Such devices can then be monitored but cannot be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { tedMainGroup } GROUP tedUnnumberedLinkGroup DESCRIPTION "This group is mandatory for TE links that support the unnumbered links." GROUP tedNumberedLinkGroup DESCRIPTION "This group is mandatory for TE links that support the numbered links." GROUP tedSwCapGroup DESCRIPTION "This group is mandatory for TE links that support some GMPLS switching capabilities." GROUP tedSwCapMinLspBandwidthGroup DESCRIPTION "This group is mandatory for TE links if the switching capability field is TDM, PSC-1, PSC-2, PSC-3, or PSC-4." GROUP tedSwCapIfMtuGroup DESCRIPTION "This group is mandatory for TE links that support the MTU of the local or remote TE link." GROUP tedSwCapIndicationGroup DESCRIPTION "This group is mandatory for TE links that support Standard or Arbitrary SONET/SDH." GROUP tedSrlgGroup DESCRIPTION "This group is mandatory for TE links that support SRLG information." ::= { tedCompliances 2 } -- Units of conformance tedMainGroup OBJECT-GROUP OBJECTS { tedLinkState, tedAreaId, tedLinkType, tedTeRouterIdAddrType, tedTeRouterIdAddr, tedLinkIdAddrType, tedLinkIdAddr, tedMetric, tedMaxBandwidth, tedMaxReservableBandwidth, tedUnreservedBandwidthPri0, tedUnreservedBandwidthPri1, tedUnreservedBandwidthPri2, tedUnreservedBandwidthPri3, tedUnreservedBandwidthPri4, tedUnreservedBandwidthPri5, tedUnreservedBandwidthPri6, tedUnreservedBandwidthPri7, tedAdministrativeGroup, tedLinkProtectionType, tedLinkInformationData } STATUS current DESCRIPTION "Collection of objects for TED management" ::= { tedGroups 1 } tedObjectsGroup OBJECT-GROUP OBJECTS { tedStatusChangeNotificationMaxRate, tedCreatedDeletedNotificationMaxRate } STATUS current DESCRIPTION "The objects needed to implement notification." ::= { tedGroups 2 } tedNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { tedStatusChange, tedEntryCreated, tedEntryDeleted } STATUS current DESCRIPTION "This group is mandatory for those implementations that can implement the notifications contained in this group." ::= { tedGroups 3 } tedUnnumberedLinkGroup OBJECT-GROUP OBJECTS { tedLocalId, tedRemoteId } STATUS current DESCRIPTION "The objects needed to implement the unnumbered links." ::= { tedGroups 4 } tedNumberedLinkGroup OBJECT-GROUP OBJECTS { tedLocalIfAddrType, tedRemoteIfAddrType } STATUS current DESCRIPTION "The objects needed to implement the numbered links." ::= { tedGroups 5 } tedSwCapGroup OBJECT-GROUP OBJECTS { tedSwCapType, tedSwCapEncoding, tedSwCapMaxLspBandwidthPri0, tedSwCapMaxLspBandwidthPri1, tedSwCapMaxLspBandwidthPri2, tedSwCapMaxLspBandwidthPri3, tedSwCapMaxLspBandwidthPri4, tedSwCapMaxLspBandwidthPri5, tedSwCapMaxLspBandwidthPri6, tedSwCapMaxLspBandwidthPri7 } STATUS current DESCRIPTION "The objects needed to implement the TE links with GMPLS TE switching capability information." ::= { tedGroups 6 } tedSwCapMinLspBandwidthGroup OBJECT-GROUP OBJECTS { tedSwCapMinLspBandwidth } STATUS current DESCRIPTION "The objects needed to implement the minimum bandwidth of the TE link for GMPLS LSP creation." ::= { tedGroups 7 } tedSwCapIfMtuGroup OBJECT-GROUP OBJECTS { tedSwCapIfMtu } STATUS current DESCRIPTION "The objects needed to implement the MTU information of the local or remote TE link." ::= { tedGroups 8 } tedSwCapIndicationGroup OBJECT-GROUP OBJECTS { tedSwCapIndication } STATUS current DESCRIPTION "The objects needed to implement the indication of whether the interface supports Standard or Arbitrary SONET/SDH." ::= { tedGroups 9 } tedSrlgGroup OBJECT-GROUP OBJECTS { tedSrlg } STATUS current DESCRIPTION "The objects needed to implement multiple SRLG values with GMPLS TE information." ::= { tedGroups 10 } END